20166131 - Permit (2) - Laserfiche WebLink

Home Browse Search

EXPEDITED PERMIT PROCESS FOR SMALL-SCALE PV SYSTEMS STANDARD STRINC SYSTEM The information in this guideline is intended to help local jurisdictions and contractors identify when PV system installations are simple, needing only a basic review and when an insEllation is more complex. lt is likely that 50%-75% of all residential systems will comply with these simple criteria. For projects that fail to meet the simple criteria, resolution steps have been suggesled to provide as a path to permir approval. Required Infornation for Pennit: 1. Site plan showing location oF major components on the property. This drawing need not be exactly to scale, but it should represent relative location of components at site (see supplied example site plan). PV arrays on dwellings with a 3'perimeter space at ridge and sides may not need separate nre service review. 2. Electrical diagram showing PV array confrguration, wiring system, overcurrent protection, invertet disconnects, required signs, and ac connection to building (see supplied standard electrical diagram). 3 Specification sheets and installation manuals (if available) for all manufactured componenm including, but not limited to, PV modules, inverter(s), combiner box, disconnects, and mounting system. Step 1 : Structural Review o[ PV Array Mounting System Is the array to be mounted on a defined, permitted rcof structure? Eyes Er,lo Il No due to non-compliant roo.f or a ground mount, submit compLeted worksheet Jor the structure wKSl . Roof Inforrnation: YESl. ls the roohng type lightweighr (Yes : composition, lightweight masonry. metal. elc ..) U No, submit completed worksheet Jor roof structure Wt(S,l (No = heavy masonry, slate, etc...) 2 Does the roof have a single roof coveringz Eyes E r,lo IJ No, submit completed worhsheet Jor rooJ structure wKSl . Flashing, geocell sealant M ount ing Sy st efi InJorTn at i on : neered product designed to mount PV modules with no more than an 18" gap Yes E no Il No, provide details oJ structurql attqchment certifed b)/ a design projessiond. 2. For manufadured mounring systems, 6ll out information on the mounting system below stem Manufacturer ZS producr Name and 114o6"11Comp V4 w flashing-insert 1006 l. Is the mounting structure an en benearh the rnodule frames? a. Mounting Sy b. Total Weight of PV Modules and Rails bs c. Total Number of Attachmenl Poin d. Weight per Attachment Point (b : c)bs (if greater than 45 lbs, see WKS I ) t.63 15.96 e Maximum Spacing Between A[tachment Points on a Rail 48 inches (see product manual For maximum spacing allowed based on maximum design wind speed) Total Surface Area of PV Modules (square feet)349f g tu' Distributed Weight of PV Module on Roof (b - l)2.88 lbs/ftl Il distributed weight of the Pv system is grcater than 5 lbsfP, see wKSl . Step 2: Electrical Review o[ PV System (Calculations for Electrical Diagram) tn order for a Pv s]Etem to be considerâ‚¬d for an expedited permit process, the following must apply: 1. PV modules, utility-interacrive inverters, and combiner boxes are identihed for use in PV systems. 2. The PV array is composed of 4 series strings or less per inverter. 3. The toml inverter capacity has a continuous ac power output 13,440 Watts or less 4. The ac inrerconnec[ion point is on the load side of service disconnecting means (690.64(8)). 5. One of rhe srandard elecrrical diagrams(El.l,El.la,El.lb,orE1.lc)canbeusedtoaccuratelyrepresentthePV system. lnteractive PDF diagrams are available at www.solarabcs.org/permitting. Fill out the standard electical diagram compleiety. A guide to the electrical diagram is provid.ed to help the appltcant understand each blank to ltl in. Il the electrical system is more complex than the standard electrical diagram can ellectively communicate, provide qn alternatfue dtagram n)ith appropriate detail. 2 EXPEDITED PERMIT PROCES5 FOR PV SYSTEMS 3 Provide method and rype of weatherproofrng roof penetralions (e.9. flashing, caulk)