Laserfiche WebLink
15 SIGN COMPONENTS MANUAL (SAM)November 14,2012 <br />ABLE APPLIED TECHNOLOGIES LTD E329973 <br />BOUNDARY HOUSE BUSINESS CENTER <br />BOSTON MANOR RD <br />LONDON, W7 2QE UNITED KINGDOM <br />Class 2 LED Modules, Models MS-P40XXX-XX Series, where XXX-XX may be any alphanumeric characters. <br />1. These LED panel of these products are powered by Class 2 power source rated at max. 15 VDC, 5 amps. <br />2. These products are suitable for use in dry and damp locations. <br />3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, <br />and minimum 2 inches spacing to top of enclosure. <br />4. In the end product the LED face shall be protected from rain. <br />ADHESIVE SYSTEMS INC <br />9411 CORSAIR RD <br />E350958 <br />FRANKFORT, IL 60423 <br />Polymeric adhesive system, Cat. No. MP55420. <br />1. The use of these adhesive systems shall be employed in applications wherein the limitations specified in Table A are not <br />exceeded. <br />2. These systems may be used for securement to any combination of surfaces Listed in Table A, provided the use temperature is <br />no higher than 71°C. <br />3. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been <br />performed on the adhesive by itself. The Engineer must consider the need to investigate the part of other than the properties <br />investigated, in accordance with the applicable UL-end product Standard or requirements outlined in the Standard for Polymeric <br />Materials - Use in Electrical Equipment Evaluations, UL 746C. <br />4. The suitability for use when exposed to oil, chemicals, refrigerant, soaps, X-rays, ultraviolet light and the like, has not been <br />determined. <br />5. These systems are suitable for application to smooth flat surfaces. The need for adhesive bond strength test when applied to <br />another surface or configuration shall be determined in the particular end use application. <br />6. These systems are also suitable where exposed indoors or outdoors to high humidity or occasional exposure to water. The <br />minimum temperature rating is -35°C (-31°F). <br />7. The adhesive shall be applied in accordance with the manufacturer's instruction. All surfaces shall be clean and dry. The <br />manufacturer's instructions regarding cure time shall be followed. <br />8. The adhesive bond strength specified in Table A includes a safety factor of four. <br />9. When considering the use of any adhesive covered by this Report, the strength of the adhesive joint used to position parts shall <br />be capable of withstanding the maximum force that might be applied to the joint in the end application. This is called the bond <br />strength and indudes static load as well as wind loading(dynamic load). The minimum square inches of adhesive to use is <br />determined by dividing the maximum load in pounds by the adhesive bond strength specified in Table A. <br />ADVANCED LIGHTING CONCEPTS INC,E345129 <br />DBA ENVIRONMENTALLIGHTS.COM <br />SUITE 102 <br />11235 W BERNARDO CT <br />SAN DIEGO, CA 92127 <br />Class 2 Power Supply, Models 4x60W12VDimX-120AC, 3x96W24VDimX-120AC. <br />1. These power supplies have been evaluated for use in LED signs. <br />2. The power supplies have outputs that individually comply with Class 2 circuit requirements. <br />3. These units are suitable for use in dry and damp locations without a need for an additional enclosure. <br />4. The output of this power source shall not be connected to any other power source or provide power to components connected to <br />another power source. <br />5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least <br />150 mm (6 in) inside. <br />>AGILIGHT INC E255447 <br />SUITE 108 <br />1218 ARION PKY <br />SAN ANTONIO, TX 78216 <br />Class 2 LEDs, Cat. No. "SideWinder" may be followed by (Standard) or "Side\Ninder BL" Cat Nos. LS-A-BBB-GZ, where A (model <br />or series name, e.g. SideWinder) and BBB (color designation) may be replaced by alphanumeric characters; and Z may be <br />replaced with alpha characters to denote generation number. 1. These products are only suitable for connection to a UL Listed or <br />Recognized maximum Class 2,12 V AC or DC power source. <br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 circuit <br />limits. <br />3. These Class 2 LED modules, are each rated max. 40 Watts per unit, LED module. When units are connected to a Class 2 <br />circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. <br />4. These products are suitable for use in dry, damp or wet locations. <br />5. These products are not required to be enclosed or protected from the weather. <br />6. These products may be secured in place in the end product by any means available. <br />7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall <br />be considered.