Laserfiche WebLink
121 SIGN COMPONENTS MANUAL (SAM)November 14,2012 <br />3. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class <br />2 circuit. <br />4. These products are provided with wire soldered on the printed wiring board for connection. <br />5. These products are suitable for use in dry, damp and wet locations. <br />Class 2 LEDs, Modules designated, "LED STRIPE2 (Border Light)" and "701956-XXXXXX" series, where XXXXXX may be <br />replaced with alphanumeric characters. <br />1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source. <br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 <br />voltage and energy limited supplies. <br />3. Class 2 LEDs, "LED STRIPE2 (Border Light)", is rated max, 48 Watts per module. When units are connected to a Class 2 <br />circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. <br />4. These products are suitable for use in dry, damp and wet locations. <br />Class 2 LED Module, Cat. No. 701269-=-MB Series, where x=xxx=xx maybe blank or any alphanumeric characters. <br />1. These products have been evaluated only for use when connected to the Class 2 output of a Listed or Recognized power <br />source rated 15 V DC or less. <br />2. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15VDCor less. <br />3. These products are not required to be enclosed or protected from the weather in the end product. <br />4. These products may be secured in the end product with any available means. <br />5. These products are rated for a maximum of 7.5 watts or less per module. <br />Class 2 LED Border Light, Class 2 "Border Light", Cat. No. 701189-XXXXXXXXXX series. <br />1. These products are only suitable for connedion to a Class 2 power source, rated 30 Volt DC or less. <br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage <br />and energy limits and which is rated greater than 30 V DC. <br />3. These products are each rated max. 100 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a <br />total wattage of greater than the secondary or output rating of the Class 2 supply. <br />4. These products are suitable for use in dry, damp and wet locations when rated maximum 30 VDC. <br />5. These products are not required to be enclosed or protected from the weather in the end product when rated 30 VDC or less. <br />6. These products may be secured in place in the end product by any means available. <br />7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall <br />be considered. <br />LED Strips, Cat. No. 701174, 701181 and 701195 with suffix -R, -Y, -A, -B, AN, or -G followed by -1" through -24" <br />1. These products are only suitable for connection to a UL Listed or Recognized Class 2,24 volt AC power source. <br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 <br />voltage and energy limited supplies. <br />3. These products may be cut into segments through a black mark provided on the printed wiring board. No other cut across the <br />board is permitted. <br />4. Cat. No. 701174 is rated for 4.2 watts per foot, Cat. No. 701181 is rated for 9.2 watts per foot and Cat. No. 701195 is rated at <br />1.5 Watts per foot. The total number of feet of each type and inches for the inch unit are not to produce a total wattage of <br />greater than 60 watts per Class 2 circuit. <br />5. These products are suitable for use in dry, damp and wet locations. <br />6. These products are not required to be endosed or protected from weather. <br />Class 2 LED Module, Cat. No. 701946-XXYYYYYYZZZ series, where XX, YYYYYY and ZZZ may be replaced with any <br />alphanumeric characters or blank. <br />1. These products are suitable for use in dry, damp and wet locations and supplied only with a Class 2 power source rated 24 Volt <br />DC or less. <br />2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating <br />of the Class 2 supply. <br />3. These products are not required to be endosed or protected from the weather in the end product. <br />4. These products may be secured in place in the end product by any means available. <br />Class 2 power supply, Model 701285. <br />1. Power supply is intended to power LEDs in signs. <br />2. Power supply model is intended for permanent connection only. <br />3. These units are suitable for use in dry location without a need for an additional enclosure and in damp locations when installed <br />inside a sign that complies with the Exclusion of Water Test in UL 48. <br />4. If the power supply output wiring is extended longer than the 5 foot leads provided, the spliced connections shall be made <br />inside a Listed junction box suitable for the application included with proper grounding. <br />Class 2 power supply, Cat. Nos. 701349, 701351. <br />1. Power supply models 701349 and 701351 are intended to power LEDs in signs. <br />2. Power supply model 701349 and 701351 are intended for permanent connection only. <br />3. These units are suitable for use in dry location without a need for an additional enclosure and in damp locations when installed <br />inside a sign that complies with the Exclusion of Water Test in UL 48. <br />5. These power supplies have two outputs. The Class 2 output circuits are not to be conductively connected to each other in the <br />sign by wiring or other type of component. <br />6. The maximum rated output power for Model 701349 is 42 watts at each Class 2 output. The maximum rated output power for <br />Model 701351 is 60 watts at each Class 2 output. <br />Class 2 power supplies, Models 701507-MOD, 701507-MOD277 (AD060S277/347-SLN). All may be followed by alphanumeric <br />sumx. <br />1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class <br />2 output requirements for dc circuits. <br />2. These products with Class 2 outputs are suitable for use in dr'y, damp and wet locations. <br />3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, <br />and minimum 2 inches spacing to top of enclosure. <br />4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on primary <br />circuit.