Laserfiche WebLink
REV <br />SHEET NAME <br />SHEET SIZE <br />SHEET NUMBER <br />DO <br />U <br />G <br /> <br />R <br />I <br />S <br />K <br />61 <br />0 <br /> <br />E <br /> <br />S <br />A <br />N <br />T <br />A <br /> <br />C <br />L <br />A <br />R <br />A <br /> <br />A <br />V <br />E <br />, <br />SA <br />N <br />T <br />A <br /> <br />A <br />N <br />A <br />, <br /> <br />C <br />A <br /> <br />9 <br />2 <br />7 <br />0 <br />6 <br />, <br /> <br />U <br />S <br />A <br />ANSI B <br />11" X 17" <br />DATE DESCRIPTION <br />REVISIONS <br />Signature with Seal <br />PROJECT NAME & ADDRESS <br />PV-1 <br />CONTRACTOR NAME <br />CONTRACTOR INFORMATION <br />8001 CANOGA AVE #B <br />CANOGA PARK, CA 91304 <br />PHONE: 1(818) 564-4820 <br />COASTAL BUILDERS <br />610 E. SANTA CLARA AVE. <br />SANTA ANA, CA 92706 <br />(714) 234-9160 <br />CALIFORNIA <br />LIC# 623480- B <br />COVER SHEET <br />SCOPE OF WORK <br />SYSTEM SIZE: 7.04KW <br />CEC AC: 6.53KW <br />MODULES: (22) HANWHA Q.CELLS: Q.PEAK DUO BLK-G5 320W MODULES <br />MODULE MAX POWER (P/MAX): 320W <br />INVERTER: (1) SOLAREDGE SE7600H-US000BNU4 INVERTER <br />OPTIMIZER: (22) SOLAREDGE POWER OPTIMIZER P320 <br />RACKING: IRONRIDGE XR10 RAIL <br />ATTACHMENT: UNIRAC UNIVERSAL TILE HOOK <br />VICINITY MAP <br />BUILDING INFORMATION: TWO STORY HOUSE <br />TYPE OF CONSTRUCTION: V-B <br />OCCUPANCY: RESIDENTIAL GROUP R - 3 <br />APN# 00313203 <br />ROOF TYPE: S-TILE <br />RAFTERS: 2"X4" @ 24" O.C. <br />ELECTRICAL INFORMATION <br />UTILITY COMPANY: SCE <br />MAIN SERVICE AMPERAGE: 200A <br />ARRAY TILT UP: <br />#1 - 27° <br />ARRAY AZIMUTH: <br />#1 - 90° <br />TABLE OF CONTENTS <br />PAGE #DESCRIPTION <br />PV 1 COVER SHEET <br />PV 2 SITE PLAN <br />PV 3 ARRAY DETAIL <br />PV 4 STRING LAYOUT <br />PV 5-6 ATTACHMENT DETAIL <br />PV 7 ELECTRICAL DIAGRAM <br />PV 8 ELECTRICAL CALCULATION <br />PV 9 PLACARD <br />PV 10 OPTIMIZER CHART <br />PV 11+SPEC SHEETS <br />THIS PROJECT SHALL COMPLY WITH THE FOLLOWING CODE <br />2019 CALIFORNIA ELECTRICAL CODE <br />2019 CALIFORNIA RESIDENTIAL CODE <br />2019 CALIFORNIA BUILDING CODE <br />2019 CALIFORNIA GREEN BUILDING STANDARDS CODE <br />2019 CALIFORNIA ENERGY CODE <br />2019 CALIFORNIA PLUMBING CODE <br />2019 CALIFORNIA MECHANICAL CODE <br />2019 NATIONAL ELECTRICAL CODE <br />ALL OTHER ORDINANCES ADOPTED BY THE LOCAL <br />GOVERNING AGENCIES. <br />CODE SUMMARY <br />GENERAL NOTES: <br />· LOCAL UTILITY PROVIDER SHALL BE NOTIFIED PRIOR TO USE AND ACTIVATION OF ANY SOLAR <br />PHOTOVOLTAIC INSTALLATION. <br />·THIS PROJECT SHALL COMPLY WITH LOCAL ORDINANCES <br />·PROPER ACCESS AND WORKING CLEARANCE WILL BE PROVIDED <br />·ALL ELECTRICAL WORK SHOWN ON THESE PLANS WILL BE COMPLETED BY THE UNDERSIGNED <br />·ALL APPLICABLE PV EQUIPMENT LISTED AND COMPLIANT WITH UL2703, UL1741 AND UL1703 <br />·ALL ROOF PENETRATIONS TO BE SEALED WITH A HIGH PERFORMANCE ROOF SEALANT SUCH AS <br />GeoCel 2300 CLEAR SEALANT <br />·THE SYSTEM WILL NOT BE INTERCONNECTED UNTIL APPROVAL FROM THE LOCAL JURISDICTION <br />AND THE UTILITY IS OBTAINED <br />·THE SOLAR PHOTOVOLTAIC INSTALLATION SHALL NOT OBSTRUCT ANY PLUMBING, MECHANICAL, <br />OR BUILDING ROOF VENTS <br />·IF THE EXISTING MAIN PANEL DOES NOT HAVE VERIFIABLE GROUNDING ELECTRODE, IT IS THE <br />NECESSARY TO INSTALL A SUPPLEMENTAL GROUNDING ELECTRODE <br />·EACH MODULE WILL BE GROUNDED UL 2703 OR UL 1703 APPROVED USING THE SUPPLIED <br />CONNECTION POINTS IDENTIFIED ON THE MODULE AND THE MANUFACTURER'S INSTALLATION <br />INSTRUCTIONS" <br />·A LADDER SHALL BE IN PLACE FOR THE INSPECTION IN COMPLIANCE WITH CAL-OSHA <br />REGULATIONS <br />·PHOTOVOLTAIC SYSTEM INVERTER IS UNGROUNDED. NO CONDUCTORS ARE SOLIDLY GROUNDED <br />IN THE INVERTER, AND SYSTEM COMPLIES WITH 690.35. <br />·MODULES CONFORM TO AND ARE LISTED UNDER UL 1703. <br />·INVERTER CONFORMS TO AND IS LISTED UNDER UL 1741. <br />·ELECTRICAL EQUIPMENT AND MATERIAL TO BE LISTED, LABELED, AND INSTALLED PER THE NEC, <br />THE INSTALLATION STANDARDS/MANUFACTURER'S RECOMMENDATIONS AND IF REQUIRED A <br />RECOGNIZED ELECTRICAL TESTING LABORATORY. <br />·CONDUITS EXPOSED TO SUNLIGHT ON ROOF SHALL BE LOCATED NOT LESS THAN 7/8" ABOVE <br />ROOF SURFACE. NEC 310.15(B)(3)(c) <br />·THIS PROJECT HAS BEEN DESIGNED IN COMPLIANCE WITH THE CBC SECTION 1609 TO WITHSTAND <br />A MINIMUM 110 MPH WIND LOAD. <br />Permit # 101108446 & 20174666 <br />Issued 11/02/2021 <br />610 E Santa Clara <br />Ave11/09/21