Laserfiche WebLink
CONTRACTOR <br />Saveco Inc. <br />Address: 435 Rivera St. Suite E <br />Riverside, CA 92501 <br />License: 1052375 <br />Phone: 833-372-8326 <br />Project Name: <br />Terence Casey <br />Property address: <br />906 Catalina Ave <br />Santa Ana, CA 92706 <br />APN:00322212 <br />DATE: 07/01/2022 <br />SIGNAGE3 <br />SOLAR PV SYSTEM EQUIPPED <br />WITH RAPID SHUTDOWN <br />TURN RAPID SHUTDOWN <br />SWITCH TO THE <br />"OFF" POSITION TO <br />SHUT DOWN PV SYSTEM <br />AND REDUCE <br />SHOCK HAZARD <br />IN THE ARRAY <br />SOLAR ELECTRIC <br />PV PANELS <br />1 <br />(TO BE LOCATED ON <br />SUB-PANEL ONLY <br />WHEN SUB-PANEL IS <br />DEDICATED FOR PV ONLY) <br />3 <br />4 <br />5 <br />6 <br />(STICKER LOCATED <br />INSIDE PANEL <br />NEXT TO SOLAR BREAKER) <br /> 7 <br />(STICKER LOCATED <br />INSIDE PANEL <br />BELOW PV BREAKER) <br />PV ARRAY <br />J BOX <br />PV SUB-PANEL <br />* if applicable <br />SUB-PANEL <br />* if applicable <br />AC <br />DISCONNECT <br />* if applicable <br />METER <br />MAIN SERVICE <br />PANEL <br />1 <br />3 <br />4 <br />6 <br />5 <br /> 7 <br />4 <br />6 <br />5 <br /> 7 <br />4 <br />4 <br />6 <br />5 <br /> 7 <br /> 2 <br />(STICKER LOCATED <br />ON THE PV SUB PANEL) <br /> 2 <br /> 8 <br />(STICKER LOCATED <br />ON THE MAIN SERVICE PANEL) 8 <br />CAUTION <br />AUTHORIZED SOLAR <br />PERSONNAL ONLY! <br />PV LOAD CENTER SIZED FOR PV <br />BREAKERS ONLY OR RENDERED UNABLE <br />TO ACCEPT ANY ADDITIONAL LOADS. <br />PV SUB-PANEL ONLY <br />AC DISCONNECT <br />AC PHOTOVOLTAIC POWER SOURCE <br />RATED AC OUTPUT CURRENT: A MAX <br />NOMINAL AC OPERATING VOLTAGE: 240 Vac <br />THIS PANEL FED BY <br />MULTIPLE SOURCES <br />(UTILITY & SOLAR) <br />SOLAR <br />WARNING! <br />INVERTER OUTPUT CONNECTION. DO NOT <br />RELOCATE THIS OVERCURRENT DEVICE <br />PHOTOVOLTAIC SYSTEM <br />EQUIPPED WITH <br />RAPID SHUT DOWN <br />Permanent directory or plaque providing location of <br />service disconnecting means and photovoltaic <br />system disconnecting means, if not located at the <br />same location. (Plaques shall be metal or plastic, with <br />engraved or machine printed letters, or electro-photo <br />plating, in a contrasting color to the plaque. Plaques <br />shall be permanently attached to the equipmenq or in <br />the required location using an approved method that is <br />suitable to withstand the environment to which it is <br />exposed. Plaques and signage shall meet legibility, <br />defacemet, exposure and adhesion requirements of <br />Underwriters Laboratories marking and labeling system <br />969(UL969). <br />39.328 <br />MARKINGS, LABELS AND WIRING SIGNS <br />A. Purpose: Provide emergency responders with appropriate warning and guidance with <br />respect to isolating solar electric system. <br />This can facilitate identifying energized electrical lines that connect solar panels to the <br />inverter, as these should not be cut when venting for smoke removal <br />B. Main Service Disconnect. <br />1. Residential buildings - The marking main be placed within the main service <br />disconnect. The marking shall be placed <br /> outside cover if the main service disconnect is operable with the service panel closed. <br />2. Commercial buildings - Tha marking shall be placed adjacent to the main service <br />disconnect clearly visible from the location where the level is operated <br />3. Markings: Verbiage, Format and Type of Material. <br /> a. Verbiage: CAUTION: SOLAR ELECTRIC SYSTEM CONNECTED <br /> b. Format: White lettering on a red background. Minimum 3/8 inches letter height. All <br />letters shall be capitalized. Arial or similar font, non bold. <br /> c. Material: Reflective, weather resistant material suitable for the environment (use UL - <br />969 as standard for weather rating). Durable adhesive materials meet this requirement. <br />C.Marking Requirements on DC conduit, raceways, enclosures, cable assemblies, DC <br />combiners and junction boxes: <br /> 1. Markings: Verbiage, Format and Type of Material. <br /> a. Placement : Markings shall be placed every 10 feet on all interior and exterior DC <br />conduits, raceways, enclosures, and cable assemblies, <br />at turns, above and for below penetrations, all DC combiners and junction boxes <br /> b. Verbiage: CAUTION: SOLAR CIRCUIT Note: The format and type of material shall <br />adhere to "V. V-3b, c" of this requirement. <br /> c. Inverters are not required to have caution markings <br />1.Marking is required on all interior and exterior DC conduit raceways,enclosures,cable <br />assemblies,and junction boxes,combiner boxes and disconnects. <br />2.The materials used for marking shall be reflective,weather resistant material suitable <br />for the environment. <br />Minimum 3/8 "letter height; all upper case letters Arial or similar font; Red background <br />with white lettering. <br />3.Marcking shall contain the words: WARNING : PHOTOVOLTAIC POWER SOURCE. <br />4.Marking shall be placed adjacent to the main service disconnect in a location clearly <br />visible from the location where the disconnect is operated <br />Stickers will have red background & white lettering <br />CAUTION <br />POWER TO THIS BUILDING IS ALSO SUPPLIED <br />FROM THE FOLLOWING SOURCES WITH <br />DISCONNECTS LOCATED AS SHOWN: <br />N <br /> 0 ° <br />S <br /> 180 ° <br />E <br /> 90 ° <br />W <br /> 270 ° <br />SERVICE POINT & <br />UTILITY METERING <br />AC DISCONNECT <br />ENPHASE COMBINER <br />SOLAR PV ARRAY <br />You Are <br />Here <br />906 E Catalina Ave <br />09/29/22