Laserfiche WebLink
A B <br />-- <br />IS <br />S <br />U <br />E <br />D <br /> <br />F <br />O <br />R <br />: <br /> <br />P <br />E <br />R <br />M <br />I <br />T <br />DA <br />T <br />E <br />: <br />S <br />P <br /> <br />S <br />11 <br />/ <br />1 <br />0 <br />/ <br />2 <br />0 <br />2 <br />2 <br />RI <br />C <br />H <br />A <br />R <br />D <br /> <br />M <br />C <br />I <br />N <br />T <br />O <br />S <br />H <br />13 <br />7 <br />6 <br />1 <br /> <br />D <br />E <br />O <br />D <br />A <br />R <br /> <br />S <br />T <br />R <br />E <br />E <br />T <br />SA <br />N <br />T <br />A <br /> <br />A <br />N <br />A <br />, <br /> <br />C <br />A <br /> <br />2 <br />7 <br />0 <br />5 <br />(7 <br />1 <br />4 <br />) <br />- <br />3 <br />6 <br />3 <br />- <br />2 <br />4 <br />2 <br />1 <br />SO <br />L <br />A <br />R <br />M <br />A <br />X <br /> <br />R <br />E <br />N <br />E <br />W <br />A <br />B <br />L <br />E <br />EN <br />E <br />R <br />G <br />Y <br /> <br />P <br />R <br />O <br />V <br />I <br />D <br />E <br />R <br /> <br />I <br />N <br />C <br /> S <br />R <br />E <br />P <br /> <br />E <br />L <br />E <br />C <br />T <br />R <br />I <br />C <br />30 <br />8 <br />0 <br /> <br />1 <br />2 <br /> <br />S <br />, <br /> <br />R <br />, <br /> <br />C <br />A <br /> <br />2 <br />5 <br />0 <br />7 <br />P: <br /> <br />( <br />5 <br />1 <br />) <br /> <br />3 <br />0 <br />0 <br />- <br />0 <br />7 <br />8 <br />8 <br />D <br />B <br /> <br />H <br />, <br /> <br />L <br />. <br /> <br />H <br />PV-3A <br />EL <br />E <br />C <br />T <br />R <br />I <br />C <br />A <br />L <br /> <br />N <br />O <br />T <br />E <br />S <br />ELECTRICAL NOTES ADDITIONAL AHJ REQUIRED ELECTRICAL NOTES <br />1. PV ARRAYS ARE PER SINGLE LINE.. <br />2. PV ARRAY COMBINER/JUNCTION BOX PROVIDES TRANSITION FROM ARRAY WIRING TO <br />CONDUIT WIRING. <br />3. USE UFER GROUND ELECTRODE SYSTEM FROM INVERTER TO EXISTING MAIN SERVICE <br />GROUND ELECTRODE PER CEC 250.58. <br />4. ALL GROUND CONNECTED TO MAIN SERVICE GROUND IN MAIN SERVICE PANEL. <br />5. CONNECTORS SHALL BE POLARIS OR EUROSTRIP IT CONNECTORS. <br />6. INVERTER SHALL BE PER SINGLE LINE, SEE ATTACHED CUT SHEET. <br />7. AC DISCONNECT SHALL BE PER SINGLE LINE. <br />8. EQUIPMENT GROUNDING CONDUCTORS ON AC AND DC SIDE SIZED ACCORDING TO CEC 60. <br />. ALL CONDUCTORS SHALL BE 600V, 0C STANDARD COPPER. ALL CONDUCTORS IN CONDUIT <br />SHALL BE THWN-2. <br />10. MAXIMUM DC VOLTAGE DROP SHALL BE 1.5 <br />11. ALL CONDUCTORS SHALL BE IN CONDUIT UNLESS OTHERWISE NOTED. <br />12. ALL WORK TO COMPLY WITH 2022 CALIFORNIA ELECTRIC CODE, 2022 CALIFORNIA BUILDING <br />CODE <br />13. EXACT CONDUIT RUN LOCATIONS SUBJECT TO CHANGE. <br />14. 3.0 PSF MAX (.5 PSF FROM RACKING, 2.5 PSF FROM MODULES) DEAD LOAD CONTRIBUTED <br />FROM SOLAR ARRAY. <br />15. CONDUCTORS ON ROOF ARE TO BE A MINIMUM OF 7/8" OFF OF THE ROOF SURFACE. <br />16.GEC TO BE CONNECTED TO EXISTING UFER. IF UFER IS NOT PRESENT THEN A NEW <br />GROUND ROD WILL BE ADDED FOR GROUNDNG PURPOSES. <br />17. AN INSULATED GROUNDED CONDUCTOR OF 6 AWG OR SMALLER SHALL BE IDENTIFIED AS <br />WHITE. <br />18. AN EQUIPMENT GROUNDING CONDUCTOR SHALL NOT BE SMALLER THAN 14 AWG. <br />1. GROUNDING ELECTRODE CONDUCTOR(S) SHALL BE INSTALLED IN ONE CONTINUOUS <br />LENGTH WITHOUT A SPLICE OR JOINT. IF NECESSARY, SPLICES OR CONNECTIONS SHALL BE <br />MADE AS PERMITTED. <br />RACKING & MODULES ARE CONNECTED TO THE EGC W/ EVEREST INTEGRATED GROUND. <br />MODULES ARE FACTORY PROVIDED W/ 2 THREADED HOLES TO FACILITATE LANDING OF THE <br />LUGS <br />DC SIDE OF ARRAY IS UNGROUNDED AND THEREFORE GEC IS NOT REQUIRED. <br />ALL EQUIPMENT SHALL BE PROPERLY GROUNDED AND BONDED IN ACCORDANCE WITH <br />ARTICLE 250. <br />ALL CIRCUITS CONNECTED TO MORE THAN ONE SOURCE SHALL HAVE OVERCURRENT DEVICES <br />LOCATED SO AS TO PROVIDE OVERCURRENT PROTECTION FROM ALL SOURCES PER CEC 60. <br />(A) <br />PER 2022 CEC, 60.64 (B)(7): LOCATE INVERTER OUTPUT AS FAR AS POSSIBLE FROM NORMAL POWER <br />SUPPLY AT SERVICE PANEL. RELOCATION OF EXISTING CIRCUITS MAY BE NEEDED. DO NOT CHANGE <br />PHASING OF MULTI-WIRE CIRCUITS. PERMANENT SIGNAGE AT PV SUPPLY CIRCUIT BREAKERS MUST <br />SAY: WARNING INVERTER OUTPUT CONNECTION. DO NOT RELOCATE THIS OVERCURRENT DEVICE. <br />SIGNAGE TO BE LOCATED ADJACENT TO BACKFED BREAKER. <br />GROUNDING: <br />EVEREST INTEGRATED <br />MODEL US004000437 <br />UL LISTED 2703 <br />13761 N Deodar St - <br />201804822/21/2024