1506 E Clemensen Ave & #2 - Plan

Home Browse Search

1. WHERE CONCEALED DUCT RUNS IN SOFFITS, JOIST BAYS, VERTICAL CHASES, OR SHAFTS ARE OBSTRUCTED TO LESS THAN THE MINIMUM REQUIRED TO ALLOW THE PASSAGE OF INDICATED ROUND DUCT, PROVIDE RECTANGULAR DUCTWORK OF EQUIVALENT SIZE TO ALLOW PASSAGE OF THE DUCT RUN PAST THE OBSTRUCTION. 2. AN APPROVED SEISMIC GAS SHUTOFF VALVE SHALL BE INSTALLED ON THE FUEL GAS LINE ON THE DOWN STREAM SIDE OF THE UTILITY METER AND BE RIGIDLY CONNECTED TO THE EXTERIOR OF THE BUILDING OR STRUCTURE CONTAINING THE FUEL GAS PIPING. 3. DRAWING SYMBOL REFERENCES ARE TYPICAL AND APPLY EQUALLY TO ALL SIMILAR CONDITIONS UNLESS OTHERWISE NOTED OR OTHERWISE REFERENCED IN THE DESIGN DRAWINGS. SEE THE SYMBOLS' LEGEND ON EACH SHEET FOR DEFINITION OF ALL SYMBOLS USED IN THE DRAWINGS. 4. DETAIL REFERENCES ARE TYPICAL AND APPLY EQUALLY TO OTHER SIMILAR CONDITIONS UNLESS OTHERWISE NOTED OR OTHERWISE REFERENCED IN THE DESIGN DRAWINGS. DO NOT DISREGARD UNREFERENCED OR MISREFERENCED DETAILS. SUCH DETAILS SHALL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT AND/OR OWNER FOR INTERPRETATION OF APPLICABILITY & USAGE. 5. DO NOT SCALE DRAWINGS. 6.ALL DIMENSIONS SHALL BE VERIFIED IN FIELD. DISCREPANCIES SHALL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT AND/OR OWNER PRIOR TO PUTTING ANY AFFECTED WORK IN PLACE. 7. WOOD FRAMED BUILDINGS: ALL EXTERIOR WALL DIMENSIONS ARE TO FACE OF WOOD (FRAMING OR PLYWOOD SHEATHING WHERE OCCURS) UNLESS NOTED OTHERWISE. ALL INTERIOR WALL DIMENSIONS ARE TO FACE OF FRAMING UNLESS NOTED OTHERWISE. DIMENSIONS NOTED OTHERWISE MAY BE NOTED AS ONE OF THE FOLLOWING: C.L. CENTERLINE F.O.C. FACE OF CONCRETE F.O.F. FACE OF FINISH F.O.M. FACE OF MASONRY CLR. FACE OF FINISH AND/OR OBSTRUCTION 8. ALL FINISHED GRADE AREAS AROUND BUILDINGS SHALL SLOPE AWAY FROM BUILDINGS AT 2% MINIMUM. 9. PLUMBING FIXTURES ARE REQUIRED TO BE CONNECTED TO A SANITARY SEWER OR AN APPROVED SEWAGE DISPOSAL SYSTEM. 10. KITCHEN SINKS, LAVATORIES, BATHTUBS, SHOWERS, BIDETS, LAUNDRY TUBS & WASHING MACHINE OUTLETS SHALL BE PROVIDED WITH HOT & COLD WATER & CONNECTED TO AN APPROVED WATER SUPPLY. 11. BATHTUB & SHOWER FLOORS, WALLS ABOVE THE BATHTUBS WITH A SHOWERHEAD & SHOWERS SHALL BE FINISHED WITH A NONABSORBENT SURFACE. SUCH WALL SURFACE SHALL EXTEND TO A HEIGHT OF NOT LESS THAN 72" ABOVE THE FLOOR. 12. PROVIDE A MINIMUM 70" HIGH APPROVED NON-ABSORBANT, SHATTER-RESISTANT MATERIAL FOR SHOWER ENCLOSURES. 19B. VERTICAL DIMENSIONS ARE FROM TOP OF CONCRETE SLAB TO TOP OF PLATE AND FROM TOP OF PLYWOOD FLOOR SHEATHING TO TOP OF PLATE UNLESS OTHERWISE NOTED OR CALLED OUT IN THE DRAWINGS. THE TERM "FINISH FLOOR" EXCLUDES ANY FLOORING MATERIALS THAT MAY BE SCHEDULED AND MEANS THE TOP OF THE FINISHED CONSTRUCTION THAT IS TO RECEIVE THE FLOORING MATERIALS SUCH AS TOP OF LEVEL CONCRETE SLAB OR TOP OF LEVEL LIGHT WEIGHT FLOOR TOPPING. 20. VERIFY ALL BUILT-IN EQUIPMENT SIZES AND REQUIREMENTS PRIOR TO LAYOUT AND CONSTRUCTION. BUILT-IN EQUIPMENT SHALL FIT TIGHTLY AS POSSIBLE WITHIN MANUFACTURER'S REQUIRED TOLERANCES TO FINISHED OPENING. 21. HANDRAIL ASSEMBLIES AND GUARDS SHALL BE ABLE TO RESIST A SINGLE CONCENTRATED LOAD OF 200 LBS. APPLIED IN ANY DIRECTION AT ANY POINT ALONG THE TOP, AND HAVE ATTACHMENT DEVICES AND SUPPORTING STRUCTURE TO TRANSFER THIS LOADING TO APPROPRIATE STRUCTURAL ELEMENTS OF THE BUILDING PER 1607.7.1 AND 1607.7.1.1. 22. ALL CONCRETE SURFACES SHALL HAVE A LIGHT BROOM FINISHED, NON-SLIP SURFACE UNLESS NOTED OTHERWISE. 23. PROVIDE GALVANIC ISOLATION BETWEEN DISSIMILAR METALS. 24.ALL PIPING IN CONNECTION WITH A PLUMBING SYSTEM SHALL BE SO INSTALLED THAT PIPING OR CONNECTIONS WILL NOT BE SUBJECT TO UNDUE STRAINS OR STRESSES, AND PROVISIONS SHALL BE MADE FOR EXPANSION, CONTRACTION, AND STRUCTURAL SETTLEMENT. NO PIPING SHALL BE DIRECTLY EMBEDDED IN CONCRETE OR MASONRY. NO STRUCTURAL MEMBER SHALL BE SERIOUSLY WEAKENED OR IMPAIRED BY CUTTING, NOTCHING OR OTHERWISE. 25. AT LOCATIONS TO RECEIVE BUILT-IN CASEWORK, FIELD VERIFY ALL CLEAR OPENINGS OF CONSTRUCTION AND ADDRESS IN SHOP DRAWINGS BEFORE FABRICATION OF CASEWORK. 26. VERIFY ALL EQUIPMENT SIZES BEFORE FABRICATION OF CASEWORK. RESIDENTIAL-TYPE AND BUILT-IN KITCHEN EQUIPMENT/APPLIANCES (REFRIGERATOR, RANGE, MICROWAVE, ETC.) AND ALL OTHER BUILT-IN TYPE EQUIPMENT SHALL FIT TIGHTLY AS POSSIBLE WITHIN EQUIPMENT/ APPLIANCE MANUFACTURER'S REQUIREMENTS TO CASEWORK OPENINGS. 27. CASEWORK SHALL BE PROVIDED WITH REQUIRED HOLES, AND ACCESS PANELS FOR ELECTRICAL CABLES, PIPES, AND LIKE PENETRATING ITEMS. 28. IN NEW CONSTRUCTION CARBON MONOXIDE/SMOKE DETECTORS SHALL RECEIVE THEIR PRIMARY POWER SOURCE FROM THE BUILDING WIRING & SHALL BE EQUIPPED WITH BATTERY BACK UP & LOW BATTERY SIGNAL. SMOKE ALARMS SHALL BE LOCATED IN EACH SLEEPING ROOM, HALLWAY OR AREA GIVING ACCESS TO A SLEEPING ROOM, AND ON EACH STORY AND BASEMENT FOR DWELLINGS WITH MORE THAN ONE STORY. DETECTORS SHALL BE INTERCONNECTED SO THAT ACTUATION OF ONE ALARM WILL ACTIVATE ALL THE ALARMS WITHIN THE INDIVIDUAL DWELLING UNIT. 29. STORAGE TYPE WATER HEATERS SHALL BE STRAPPED TO THE WALL (INTO 2x BLOCKING), PER CODE. 30. BUILDING SHALL HAVE APPROVED ADDRESS NUMBERS, BUILDING NUMBERS OR APPROVED BUILDING IDENTIFICATION PLACED IN A POSITION THAT IS PLAINLY LEGIBLE & VISIBLE FROM THE STREET OR ROAD FRONTING THE PROPERTY. 31. DUCTS PENETRATING THE WALLS OR CEILINGS SEPARATING THE DWELLING FROM THE GARAGE SHALL BE CONSTRUCTED OF A MINIMUM No.26 GAUGE SHEET STEEL OR OTHER APPROVED MATERIAL & THERE SHALL BE NO OPENINGS FROM THE DUCT INTO THE GARAGE. 32. OTHER PENETRATIONS OF GARAGE/DWELLING CEILINGS & WALLS ARE TO BE PROTECTED AS REQUIRED FOR ONE HOUR ASSEMBLY 33. HEATER SHALL BE CAPABLE OF MAINTAINING A MINIMUM ROOM TEMPERATURE OF 68°F AT A POINT 3' ABOVE THE FLOOR 7 2' FROM EXTERIOR WALLS IN ALL HABITABLE ROOMS AT THE DESIGN TEMPERATURE. ENERGY AND WATER CONSERVATION 1. CAULK AND SEAL AROUND ALL PLUMBING AND ELECTRICAL PENETRATIONS INTO THE BUILDING ENVELOPE. 2. CAULK AND SEAL AROUND ALL WINDOW AND DOOR FRAMES, BETWEEN WALL SOLE PLATES AND FLOORS, AND BETWEEN EXTERIOR WALL PANELS. SEE TYPICAL EXTERIOR WALL MEASURES. 3. ALL INSULATION MATERIALS SHALL BE CERTIFIED BY THE MANUFACTURER AS COMPLYING WITH THE CALIFORNIA QUALITY STANDARDS FOR INSULATING MATERIAL. 4. DOORS AND WINDOWS BETWEEN CONDITIONED SPACE AND OUTSIDE SPACE OR BETWEEN CONDITIONED SPACE & UNCONDITIONED SPACE SHALL BE FULLY WEATHER-STRIPPED. 5. MANUFACTURED DOORS AND WINDOWS SHALL BE CERTIFIED AND LABELED IN COMPLIANCE WITH THE APPROPRIATE INFILTRATION STANDARDS. ALL EXTERIOR OPENINGS SHALL BE PROPERLY WEATHERSTRIPPED, CERTIFIED, AND LABELED. 6. DUCTS SHALL BE CONSTRUCTED, INSTALLED, AND INSULATED PER THE REQUIREMENTS OF THE U.M.C. ALL JOINTS OF THE DUCT SYSTEM SHALL BE TIGHTLY SEALED WITH MASTIC OR TAPE SUITABLE FOR THE PURPOSE. 7. ALL SPACE CONDITIONING EQUIPMENT SHALL BE C.E.C. CERTIFIED. 8.ALL WATER HEATING EQUIPMENT, SHOWER HEADS, FAUCETS, AND PLUMBING FIXTURES SHALL BE C.E.C. CERTIFIED UNLESS OTHERWISE NOTED OR APPROVED. SHOWER HEADS SHALL BE LOW FLOW TYPE. 9. GENERAL LIGHTING IN KITCHENS AND BATHROOMS SHALL HAVE A MINIMUM OF 40 LUMENS/WATT EFFICIENCY (FLUORESCENT LIGHTS OR LED WITH 3000 KELVIN MAX). 10. PROVIDE ULTRA FLUSH WATER CLOSETS FOR ALL NEW CONSTRUCTION. EXISTING SHOWER HEADS AND TOILETS MUST BE ADAPTED FOR LOW WATER CONSUMPTION. SCHEDULE IS IMPACTED BY OWNER RELATED CHANGES OR REQUESTS. AT THE TIME OF PRICING & PROIR TO CONSTRUCTION PROCEEDING. THAT ALL REQUIRED CLEARANCE FOR INSTALLATION AND TO INCLUDE ALL PIPING, DUCT WORK AND CONDUITS) LIGHTING, PLUMBING AND SPRINKLER EQUIPMENT OF ANY AND ALL MECHANICAL, TELEPHONE, ELECTRICAL, ANY CONFLICTS PRIOR TO CONSTRUCTION THAT EXIST IN LOCATIONS 3. GENERAL CONTRACTOR SHALL INFORM ARCHITECT OF PROCEEDING WITH WORK OR RELATED WORK IN QUESTION. OBTAINING A CLARIFICATION FROM ARCHITECT BEFORE QUESTIONS, THE GENERAL CONTRACTOR IS RESPONSIBLE FOR QUESTIONS REGARDING THESE OR OTHER COORDINATION BEFORE PROCEEDING WITH CONSTRUCTION. IF THERE ARE ANY ACCURACY AND CONFIRMING WORK IS BUILDABLE AS SHOWN CONTRACT DOCUMENTS, FIELD CONDITIONS AND DIMENSIONS FOR 1. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR CHECKING MAINTENANCE OF ABOVE EQUIPMENT ARE PROVIDED. AND DETAILS. CONNECTION WITH THE WORK. REQUIREMENTS. CONTRACTORS WORK. DISCIPLINE OF ALL WORKERS ON THE PROJECT. ALL OVERTIME COSTS EXCEPT WHEN THE APPROVED CONSTRUCTION 4. GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING DOCUMENTS SHALL BE FURNISHED AND INSTALLED IN 6. ALL WORK NOT SPECIFICALLY COVERED IN THE CONSTRUCTION MAINTAINING, AND SUPERVISING ALL SAFETY PRECAUTIONS IN GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR INITIATING, PROPERTY DAMAGE FOR THE LIMITS AS REQUIRED BY LAW. THE RESPECT TO WORKMAN'S COMPENSATION, PUBLIC LIABILITY AND PURCHASE AND MAINTAIN CERTIFICATIONS OF INSURANCE WITH 5. THE GENERAL CONTRACTOR AND SUBCONTRACTORS SHALL REGULATORY AGENCIES, APPLICABLE BUILDING CODES AND ALL WORK AND MATERIALS IN ACCORDANCE WITH ALL LOCAL 13. GENERAL CONTRACTOR SHALL HAVE ON-SITE, THE APPROVED AND THE OBTAINING OF A FINAL CERTIFICATE OF OCCUPANCY. DEPARTMENT INSPECTIONS AND APPROVALS IN ALL FIELDS OF HIS WORK, OF WORK, THE REQUESTING AND COORDINATION OF BUILDING REQUIRED PERMITS PRIOR TO COMMENCEMENT 12. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR OBTAINING ALL SECURITY OF PROJECT AND SHALL BE RESPONSIBLE FOR 11. THE GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR 8. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR ANY AND CONSTRUCTION TIME FOR ALL SUBCONTRACTORS AND GENERAL SPECIFIC CONSTRUCTION SCHEDULE INDICATING THE REQUIRED CONTRACTOR SHALL ALSO SUBMIT A SCHEDULE OF VALUES AND A 7. UPON SUBMITTAL OF CONSTRUCTION COSTS, THE GENERAL ACCORDANCE WITH BUILDING STANDARD MATERIALS PERSONNEL.) CONSTRUCTION DRAWINGS AND BUILDING PERMIT. ASSISTANCE AND COORDINATION OF VARIOUS TRADES. COMPLETION. SUCH INSTALLATION. JOB INCLUDING REVISIONS. CONTRACTOR SHALL COORDINATE AND COOPERATE TO EFFECT AND/OR EQUIPMENT SHALL BE PROVIDED BY OTHERS. 15. WHERE WORK OR EQUIPMENT IS INDICATED N.I.C., SUCH WORK SHALL SUBMIT CERTIFICATES OF INSPECTION OF SATISFACTORY 20. UPON COMPLETION OF THE JOB, THE GENERAL CONTRACTOR RESPONSIBILITY AT ALL TIMES DURING THE PROGRESS OF THE DRAWINGS TO ALL TRADES FALLING UNDER THEIR CONTRACTOR TO DISTRIBUTE ADEQUATE COPIES OF ALL 19. IT SHALL BE THE RESPONSIBILITY OF THE GENERAL AND NOTIFICATION SHALL BE MADE PRIOR TO INSTALLATION. USED, IT SHALL BE BY JUDGEMENT AND APPROVAL OF THE ARCHITECT MANUFACTURERS ARE SPECIFIED. WHERE APPROVED EQUAL IS SUBSTITUTIONS FOR ANY MATERIAL WHERE SPECIFIC 18. THE CONTRACTOR SHALL NOTE THAT THERE SHALL NOT BE CUTTING AND RUBBISH REMOVAL WITH BUILDING MANAGEMENT BUILDING MANAGEMENT PERSONNEL. (I.E.: DEMOLITION, 17. GENERAL CONTRACTOR SHALL COORDINATE ANY OVERTIME WITH 14. THE GENERAL CONTRACTOR SHALL PROVIDE ALL SUPERVISION, BROUGHT TO THE ATTENTION OF THE ARCHITECT & THE OWNER 16. DISCREPANCIES FOUND BETWEEN NOTES AND DRAWINGS SHALL BE GENERAL NOTES - PART B FURTHERMORE, FOR EXISTING CONDITIONS ON REMODEL/ADDITIONS, THE ARCHITECT CANNOT REALISTICALLY VERIFY ALL EXISTING CONDITIONS ACCURATELY. AS SUCH THE PREPARATION OF CONSTRUCTION DOCUMENTS ARE BASED ON TYPE V WOOD FRAME CONSTRUCTION FOR CONVENTIONAL FRAMING AND WHERE THE GENERAL CONTRACTOR MAY DISCOVER SOME DISCREPANCIES IN THE ARCHTIECT AND ENGINEERS DESIGN WITH RESPECT TO THE NEW FOUND EXISTING CONDITIONS ON SITE. THESE DISCPREPANCIES ARE EXPECTED AND A NATURAL PROCESS BECAUSE ARCHITECTURE SERVICES PRECEDES DEMOLITION OF THE PROJECT. GENERAL CONTRACTOR SHALL NOTIFY THE ARCHITECT AND/OR ENGINEER IF ANY OF THE DESIGN IS IN CONFLICT WITH THE EXISTING CONDITIONS. 10.NOT USED THESE ARE GENERAL NOTES AND SOME ITEMS MAY NOT APPLY TO THE SPECIFIC SCOPE. G.C. SHALL IN THE BEST OF JUDGEMENT, APPLY ITEMS THAT ARE RELEVANT TO THE SCOPE DISPLAYED IN THE DRAWINGS. FOR REMODELS/ADDITIONS, IN CASES WHERE A LAND SURVEY WAS NOT PERFORMED EITHER BECAUSE IT WAS NOT REQUIRED AND/OR CLIENT HAS NOT ELECTED TO FURNISH A SURVEY, ARCHITECT SHALL BASE SITE PROPERTY MEASUREMENTS FROM PERCEIVED PROPERTY LINES REPRESENTED BY FENCES, WALLS AND PLANTINGS. EVERY EFFORT WILL BE MADE TO PROVIDE AN ACCURATE MEASUREMENT HOWEVER SUCH MEASUREMENT CANNOT GUARANTEE ACCURACY DURING CONSTRUCTION. AS SUCH, IT IS UNDERSTOOD BY ALL PARTIES, OWNER, ARCHITECT, AND GENERAL CONTRACTOR, THAT DISCREPANCIES ARE POSSIBLE AND AT NO FAULT TO ANY PARTY. CLIENT MAY INCUR A MINOR CHANGE ORDER DUE TO THIS EVENT DUE TO ADJUSTMENTS IN THE DESIGN AFTER PERMIT. MATERIAL SPECIFICATIONS G.CHARLES DESIGN OFFERS ARCHITECTURE SERVICES WHERE A MAJORITY OF THE PACKAGES ARE BASED ON 'MINIMALLY TO PROCURE A BUILDING PERMIT'. THE PACKAGES ARE BASED ON THE MINIMUM REQUIREMENTS OF THE BUILDING CODES IN PLACE AT EACH JURISDICTION AND WHICH ARE LARGELY BASED ON MAINTAINING PUBLIC SAFETY. BECAUSE OUR CONSTRUCTION DRAWING PACKAGES ARE BASED ON MINIMUM REQUIREMENTS ESTABLISHED BY EACH BUILDING DEPARTMENT, OUR DETAILS ARE GENERAL AND MAY BE ADAPTED AND/OR APPLIED TO A VARIETY OF FIELD CONDITIONS. IN SOME CASES, OUR DRAWINGS WILL INDICATE MATERIAL SPECIFICATIONS FOR ITEMS SUCH AS WATER PROOF MEMBRANES THAT HELP PROTECT FROM WATER PENETRATION. IF SUCH ITEMS ARE NOT FOUND IN OUR SHEET SET, OR ARE UNCLEAR, THE GENERAL CONTRACTOR SHALL NOTIFY THE ARCHITECT TO REQUEST A DETAIL AND/OR A SPECIFICATION. IN ALL CIRCUMSTANCES, THE GENERAL CONTRACTOR SHALL UTILIZE GOOD JUDGEMENT OF THE INSTALLATION OF VARIOUS MATERIALS. AS SUCH, ALL INSTALLATIONS SHALL BE COMPLETED WITH STRICT CONFORMANCE WITH MANUFACTURER'S RECOMMENDATIONS, WRITTEN INSTRUCTIONS, INDUSTRY STANDARDS, AND BUILDING CODES. GCD 2018 GENERAL NOTES - PART A / MEANS METHODS SEQUENCES, AND TECHNIQUE 21. WORK SHALL COMPLY WITH ALL LAWS, RULES AND REGULATIONS AS REQUIRED BY THE STATE OF CALIFORNIA, THE COUNTY OF LOS ANGELES, THE CITY OF LOS ANGELES, AND ANY AND ALL OTHER GOVERNMENTAL AGENCIES HAVING JURISDICTION OVER THE WORK. THIS WILL APPLY TO ANY OTHER JURISDICTIONS SPECIFIC TO THE PROJECT SITE LOCATION OUTSIDE OF THE GREATER COUNTY OF LOS ANGELES. 22. WORK SHALL COMPLY WITH THE MODEL CODES AS ADOPTED BY LOCAL JURISDICTION, TO INCLUDE, BUT NOT LIMITED TO, (CITY OF LOS ANGELES BUILDING CODE, CALIFORNIA BUILDING CODE, INTERNATIONAL BUILDING CODE, CALIFORNIA RESIDENTIAL CODE, CALIFORNIA GREEN BUILDING STANDARDS, UNIFORM MECHANICAL CODE, UNIFORM PLUMBING CODE, NATIONAL ELECTRICAL CODE, ETC.) LOCALLY IN FORCE AT THE TIME OF BUILDING PERMIT ISSUANCE, INCLUDING ALL REVISIONS AND AMENDMENTS ADOPTED BY THE GOVERNING JURISDICTION(S). WHERE REFERENCE IS MADE TO MODEL CODE SECTIONS AND PARTS, THE CONTRACTOR SHALL BECOME FAMILIAR WITH THE MODEL CODE SECTIONS AND PARTS CITED PRIOR TO INSTALLATION OF ANY AFFECTED WORK. 23. FULLY REVIEW THE ENTIRE SET OF CONSTRUCTION DOCUMENTS PRIOR TO CONSTRUCTION. THE CONSTRUCTION DOCUMENTS MAY INCLUDE THE FOLLOWING: CIVIL DRAWINGS, DESIGN DRAWINGS, STRUCTURAL DRAWINGS, MECHANICAL DRAWINGS PLUMBING DRAWINGS, ELECTRICAL DRAWINGS, SECURITY SYSTEM DRAWINGS AND SPECIFICATIONS (DEFERRED SUBMITTAL), FIRE PROTECTION SHOP DRAWINGS AND SPECIFICATIONS (DEFERRED SUBMITTAL) 24. WHERE CONFLICT OCCURS BETWEEN THE DRAWINGS OF ANY OF THE DESIGN DISCIPLINES INVOLVED, THE MOST RESTRICTIVE INTERPRETATION WILL GOVERN THE WORK. ARCHITECT AND/OR OWNER WILL RESOLVE DESIGN CONFLICTS BASED ON THE DESIGN INTENT. 25. COORDINATE ALL CHANGES AND ADJUSTMENTS TO THE WORK WHICH VARY FROM THE CONSTRUCTION DOCUMENTS WITH ARCHITECT AND/OR PRIOR TO PUTTING WORK IN PLACE. 26. ALL PRODUCT AND COMPONENT BRANDS AND TRADEMARKS NAMED ARE USED TO SET THE LEVEL OF QUALITY REQUIRED FOR THE WORK AND ARE UNDERSTOOD TO BE "OR EQUAL" REFERENCES SUBJECT TO THE FORMAL APPROVAL PROCESS AS DESCRIBED AND SET FORTH IN THE SPECIFICATIONS UNLESS NOTED OTHERWISE. 27.THE CONTRACTOR SHALL SUPERVISE AND DIRECT THE WORK, USING CONTRACTOR'S BEST SKILL AND ATTENTION. THE CONTRACTOR SHALL BE SOLELY RESPONSIBLE FOR, AND HAVE CONTROL OVER, CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, AND PROCEDURES AND FOR COORDINATING ALL PORTIONS OF THE WORK UNDER THE CONTRACT, UNLESS THE CONTRACT DOCUMENTS GIVE OTHER SPECIFIC INSTRUCTIONS CONCERNING THESE MATTERS. 13. MATERIAL SHALL BE JOINED TO UNIFORM, ACCURATE FITS SO THEY MEET WITH NEAT, STRAIGHT LINES, FREE OF SMEARS, OVERLAPS AND IMPERFECTIONS. INSTALL EXPOSED MATERIALS . APPROPRIATELY LEVEL, PLUM AND AT RIGHT ANGLES OR FLUSH WITH ADJOINING MATERIALS. WORK OF EACH TRADE SHALL MEET OR EXCEED ALL NATIONAL STANDARDS PUBLISHED BY THAT TRADE EXCEPT WHERE THE CONTRACT DOCUMENTS ARE MORE STRINGENT. IN SUCH CASES, WORK SHALL MEET OR EXCEED THE STANDARDS ESTABLISHED BY THE CONTRACT DOCUMENTS. 14.THE CONTRACTOR SHALL , AT ALL TIMES, KEEP PREMISES FREE FROM ACCUMULATION OF DEBRIS CAUSED BY HIS OPERATIONS/WORK. 15.THE GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR CORRECTING ANY DEFECTS FOUND IN EXISTING BASE BUILDING CONSTRUCTION WHICH INTERFACES WITH NEW CONSTRUCTION. THIS INCLUDES BUT IS NOT LIMITED TO, UNEVEN SURFACES AND FINISHES AT PLASTER OR GYPSUM BOARD. THE GENERAL CONTRACTOR SHALL PATCH AND REPAIR SURFACES TO MATCH ADJACENT ADJOINING SURFACES. 28.CONTRACTOR MAY MAKE MINOR CHANGES IN THE WORK AUTHORIZED BY THE ARCHITECT IN ACCORDANCE THE SPECIFICATIONS AND SUBMITTALS. THE CONTRACTOR MAY MAKE SUBSTITUTIONS ONLY WITH THE CONSENT OF THE OWNER, AFTER EVALUATION BY THE ARCHITECT AND IN ACCORDANCE WITH A CHANGE ORDER OR CHANGE DIRECTIVE. 16. GENERAL CONTRACTOR TO VERIFY SIZES OF BUILDING ACCESS OPENINGS BEFORE PROCEEDING WITH WORK. 17.UPON COMPLETION OF THE JOB, GENERAL CONTRACTOR SHALL CLEAN ENTIRE AREA , INCLUDING GLASS, CARPET, AND ALL OTHER FINISHED SURFACES IN A MANNER ACCEPTABLE TO OWNER. 18.GENERAL CONTRACTOR IS RESPONSIBLE FOR DISPOSING OF OFF SITE PACKAGING CARTONS OR CONTAINERS, TRASH AND DEBRIS IN A SAFE, ACCEPTABLE MANNER, AND TO NO COST OR INCONVENIENCE TO OTHER PARTIES. 19.GENERAL CONTRACTOR SHALL PROVIDE PROTECTIVE COVERINGS FOR CARPET, FURNISHINGS AND EXISTING FINISHES IN AREAS OF DEMOLITION AND CONSTRUCTION AND SHALL BE RESPONSIBLE FOR THE REPAIR OF ANY DAMAGE CAUSED BY THE WORK OF THE GENERAL CONTRACTOR AND ANY SUBCONTRACTOR. CONSTRUCTION SITE PROTOCOL FOR GENERAL CONTRACTOR CONTRACTOR IS RESPONSIBLE FOR HAVING THE ORIGINAL APPROVED SET ON SITE AT ALL TIMES, AND ANY COPIES ARE REQUIRED TO BE FROM THE ORIGINAL FINAL SET OF PLANS. CONTRACTOR SHOULD NOT UN-STAPLE ANY BINDED SETS. 9.NOT USED Scale Project number Date Drawn by A-0.1 GENERAL NOTES 37-23 08/2024 JENNY PARADA 613 S EASTBURY AVE, COVINA CA 91723 No.Description Date jenny_parada@verizon.net Owner Address NANCY CALTAGIRONE Main House: 1506 E CLEMENSEN AVE SANTA ANA, CA 92705 ADU: 1506 E CLEMENSEN AVE # 2 SANTA ANA, CA 92705 PHONE: 714-997-0313 1506 E Clemensen Ave & #212/12/2024