|
PUMP
<br />TAG LOCATION MANUFACTURER &
<br />MODEL No.SERVING GPM HEAD
<br />(ft)RPM BHP HP MOTOR
<br />ENCL.
<br />PUMP
<br />EFF %
<br />PUMP
<br />DUTY %VOLTAGE EMERGENCY
<br />POWER VIB. ISO WEIGHT
<br />(lbs)
<br />VFD
<br />(Y/N)
<br />PRESSURE
<br />RATING
<br />(psi)
<br />REMARKS
<br />HHWP-1 ROOF BELL & GOSSETT
<br />E-1510 1.5AD B-1 80 50 1734 1.48 2 -68.2 100 230V-3ɸ N N 173 Y 175 -
<br />HHWP-2 ROOF BELL & GOSSETT
<br />E-1510 1.5AD B-1 80 50 1734 1.48 2 -68.2 100 230V-3ɸ N N 173 Y 175 -
<br />AIR SEPARATOR
<br />TAG LOCATION MANUFACTURER &
<br />MODEL No.SERVING GPM
<br />PRESSURE
<br />DROP
<br />(ft w.c.)
<br />INLET /
<br />OUTLET
<br />PRESSURE
<br />RATING
<br />(psig)
<br />WEIGHT
<br />(lbs)REMARKS
<br />AS-1 ROOF BELL & GOSSETT
<br />RL-2-1/2N B-1 80 1 2-1/2"125 108 -
<br />CHEMICAL POT FEEDER
<br />TAG LOCATION MANUFACTURER &
<br />MODEL No.VOLUME (gal)WEIGHT
<br />(lbs)REMARKS
<br />CPF-1 ROOF WINGERT
<br />5HD 5 37 -
<br />MECHANICAL
<br />MANDATORY MEASURES
<br />Equipment Efficiencies (§110.2)
<br />Ventilation (§120.1)
<br />Controls (§120.2)
<br />Pipe Insulation (§120.3)
<br />Duct Construction and Insulation (§120.4)
<br />Acceptance Tests (§120.5 and Reference Nonresidential Appendix NA7)
<br />MECHANICAL EQUIPMENT INSTALLED IN A BUILDING SUBJECT TO THESE REGULATIONS MUST BE CERTIFIED AS
<br />MEETING CERTAIN MINIMUM EFFICIENCY. THESE REQUIREMENTS ARE CONTAINED IN §110.2. THE AFUE, COP, EER, IPLV,
<br />COMBUSTION EFFICIENCY, AND THERMAL EFFICIENCY VALUES OF ALL EQUIPMENT MUST BE DETERMINED USING THE
<br />APPLICABLE TEST METHOD SPECIFIED IN THE STANDARDS.
<br />BUILDINGS, OTHER THAN HEALTHCARE FACILITIES, SHALL COMPLY WITH THE APPLICABLE DEMAND RESPONSIVE
<br />CONTROL REQUIREMENTS OF SECTION 110.12(a) THRU 110.12(e).
<br />ALL GAS AND OIL FIRED AIR FURNACES WITH INPUT RATING >225,000 BTU/HR SHALL HAVE AN INTERMITTENT IGNITION
<br />OR INTERRUPTED DEVICE (IDD), AND HAVE EITHER POWER VENTING OR A FLUE DAMPER.
<br />ALL OCCUPIABLE SPACES IN HIGH-RISE RESIDENTIAL, HOTEL/MOTEL AND NONRESIDENTIAL BUILDINGS OTHER THAN
<br />HEALTHCARE FACILITIES SHALL COMPLY WITH THE APPLICABLE REQUIREMENTS OF SECTION 120.1(a) THROUGH 120.1(g).
<br />HEALTHCARE FACILITIES SHALL BE VENTILATED IN ACCORDANCE WITH CHAPTER 4 OF THE CALIFORNIA MECHANICAL
<br />CODE.
<br />THE OUTDOOR AIR-VENTILATION RATE AND AIR-DISTRIBUTION ASSUMPTIONS MADE IN THE DESIGN OF THE VENTILATING
<br />SYSTEM SHALL BE CLEARLY IDENTIFIED ON THE BUILDING PLANS REQUIRED BY §10-103 OF TITLE 24, PART 1.
<br />THERMOSTATIC CONTROLS FOR EACH ZONE. THE SUPPLY OF HEATING AND COOLING ENERGY TO EACH
<br />SPACE-CONDITIONING ZONE OR DWELLING UNIT SHALL BE CONTROLLED BY AN INDIVIDUAL THERMOSTATIC CONTROL
<br />THAT RESPONDS TO TEMPERATURE WITHIN THE ZONE AND THAT MEETS THE APPLICABLE REQUIREMENTS OF
<br />SECTION 120.2(b).
<br />CRITERIA FOR ZONAL THERMOSTATIC CONTROLS. THE INDIVIDUAL THERMOSTATIC CONTROLS REQUIRED BY
<br />SECTION 120.2(a) SHALL MEET THE FOLLOWING REQUIREMENTS: FOR HEATING SHALL BE CAPABLE OF BEING SET,
<br />LOCALLY OR REMOTELY, DOWN TO 55°F OR LOWER, OR FOR COOLING IT SHALL BE CAPABLE OF BEING SET, LOCALLY OR
<br />REMOTELY, UP TO 85°F OR HIGHER.
<br />FOR HOTEL/MOTEL GUEST ROOM THERMOSTATS; SHALL HAVE: NUMERIC TEMPERATURE SETPOINTS IN °F; AND
<br />SETPOINT STOPS ACCESSIBLE ONLY TO AUTHORIZED PERSONNEL, SUCH THAT OCCUPANTS CANNOT ADJUST MORE
<br />THAN +/-5°F. THERMOSTATS SHALL ALSO COMPLY WITH SECTION 110.2(c).
<br />HEAT PUMP CONTROLS. ALL HEAT PUMPS WITH SUPPLEMENTARY ELECTRIC RESISTANCE HEATERS SHALL BE
<br />INSTALLED WITH CONTROLS THAT COMPLY WITH SECTION 110.2(b).
<br />DAMPERS FOR AIR SUPPLY AND EXHAUST EQUIPMENT. OUTDOOR AIR SUPPLY AND EXHAUST EQUIPMENT SHALL BE
<br />INSTALLED WITH DAMPERS THAT AUTOMATICALLY CLOSE UPON FAN SHUTDOWN.
<br />ISOLATION AREA DEVICES. EACH SPACE-CONDITIONING SYSTEM SERVING MULTIPLE ZONES WITH A COMBINED
<br />CONDITIONED FLOOR AREA OF MORE THAN 25,000 SQUARE FEET SHALL BE DESIGNED, INSTALLED, AND CONTROLLED
<br />TO SERVE ISOLATION AREAS.
<br />THE PIPING FOR ALL SPACE-CONDITIONING AND SERVICE WATER-HEATING SYSTEMS WITH FLUID TEMPERATURES
<br />LISTED IN TABLE 120.3-A SHALL INSTALL THE AMOUNT OF INSULATION SPECIFIED.
<br />ALL AIR DISTRIBUTION SYSTEM DUCTS AND PLENUMS, INCLUDING, BUT NOT LIMITED TO, BUILDING CAVITIES,
<br />MECHANICAL CLOSETS, AIR-HANDLER BOXES AND SUPPORT PLATFORMS USED AS DUCTS OR PLENUMS, SHALL BE
<br />INSTALLED, SEALED AND INSULATED TO MEET THE REQUIREMENTS OF THE CMC SECTIONS 601, 602, 603, 604, 605,
<br />AND SMACNA-006-2006 HVAC DUCT CONSTRUCTION STANDARDS METAL & FLEXIBLE, 3RD EDITION.
<br />BEFORE AN OCCUPANCY PERMIT IS GRANTED THE CERTIFICATE OF ACCEPTANCE SHALL BE SUBMITTED TO THE
<br />ENFORCEMENT AGENCY THAT CERTIFIES THAT THE EQUIPMENT AND SYSTEMS MEET THE ACCEPTANCE REQUIREMENTS.
<br />2022
<br />ALL NEWLY INSTALLED AIR HANDLER UNITS GREATER THAN 33,000 BTU/HR WITH AN AIR ECONOMIZER SHALL HAVE
<br />FAULT DETECTION AND DIAGNOSTICS.
<br />DDC CONTROLS TO ZONE SHALL BE PROVIDED AS SPECIFIED BY TABLE 120.2-A. SPACE CONDITIONING SYSTEMS
<br />WITH DDC CONTROLS SHALL HAVE OPTIMUM START/STOP CONTROLS.
<br />Nonresidential Building Commissioning (§120.8)
<br />NEW NONRESIDENTIAL BUILDINGS <10,000 SQ. FT. SHALL COMPLY WITH THE APPLICABLE REQUIREMENTS OF
<br />SECTIONS 120.8(a) THRU 120.8(i) IN THE BUILDING DESIGN AND CONSTRUCTION PROCESSES.
<br />Commercial Boilers (§120.9)
<br />ALL NEW BOILERS OVER 2,500,000 BTU/HR SHALL COMPLY WITH COMBUSTION AIR AND COMBUSTION AIR FAN
<br />REQUIREMENTS.
<br />OCCUPANCY SENSING ZONE CONTROLS. WHERE THE SYSTEM PROVIDING SPACE CONDITIONING ALSO PROVIDES
<br />THE VENTILATION REQUIRED BY SECTION 120.1 AND INCLUDES OCCUPANT SENSOR VENTILATION CONTROL AS
<br />SPECIFIED IN SECTION 120.1(d)5, THE OCCUPANT SENSING ZONE CONTROLS SHALL ADDITIONALLY COMPLY WITH
<br />THE FOLLOWING: PLACE THE ZONE IN OCCUPIED STANDBY MODE WHEN ALL ROOMS SERVED BY THE ZONE ARE
<br />UNOCCUPIED FOR MORE THAN 5 MINUTES AND RESET COOLING AND HEATING SETPOINTS BY 2°F (0.5°F FOR DDC
<br />SYSTEMS), AND SHUTOFF AIRFLOW TO THE ZONE WHEN IN DEADBAND.
<br />Demand Management (§110.12, 120.1(d)3)
<br />ALL DEMAND RESPONSIVE CONTROLS SHALL BE CERTIFIED OPEN ADR 2.0A OR B VIRTUAL END NODE. DEMAND
<br />RESPONSIVE CONTROL THERMOSTATS SHALL COMPLY WITH REFERENCE JOINT APPENDIX 5 (JA5).
<br />NONRESIDENTIAL HVAC SYSTEMS WITH DDC TO THE ZONE LEVEL SHALL ALLOW CENTRALIZED DEMAND SHED FOR
<br />NON-CRITICAL ZONES AS FOLLOWS: INCREASE COOLING SETPOINT AND DECREASE HEATING SETPOINT BY MIN. 4°F,
<br />ALLOW FOR REMOTE RESET TO ORIGINAL SETPOINTS, ADJUSTABLE RATE OF CHANGE FOR TEMPERATURE INCREASE,
<br />DECREASE AND RESET, DISABLED OR MANUAL CONTROL BY AUTHORIZED FACILITY OPERATOR, AUTOMATIC DEMAND
<br />SHED CONTROL UPON RECEIPT OF DEMAND RESPONSE SIGNAL.
<br />A CRITICAL ZONE IS DEFINED AS A ZONE SERVING A PROCESS WHERE RESET OF THE ZONE TEMPERATURE DURING A
<br />DEMAND SHED EVENT MIGHT DISRUPT THE PROCESS, INCLUDING BUT NOT LIMITED TO COMPUTER ROOMS, DATA
<br />CENTERS, TELECOM, PRIVATE BRANCH EXCHANGE ROOMS AND LABORATORIES.
<br />PROVIDE MIN. 2" DEPTH MERV 13 FILTRATION TO SYSTEMS SUPPLYING AIR THROUGH DUCTWORK EXCEEDING 10FT IN
<br />LENGTH, MECHANICAL SUPPLY-ONLY VENTILATION SYSTEMS, OR SUPPLY SIDE OF MECHANICAL BALANCED VENTILATION
<br />SYSTEMS.
<br />DEMAND VENTILATION CONTROLS COMPLYING WITH 120.1(d)4 ARE REQUIRED FOR A SPACE WITH A DESIGN OCCUPANT
<br />DENSITY EQUAL TO 40 SQ. FT. PER PERSON OR LESS IF THE VENTILATION SYSTEM SERVING THE SPACE HAS EITHER
<br />AN AIR ECONOMIZER, MODULATING OSA CONTROL OR DESIGN OUTDOOR AIRFLOW RATE GREATER THAN 3,000 CFM.
<br />OCCUPANT SENSOR VENTILATION CONTROL DEVICES WHEN REQUIRED BY SECTION 120.2(e)3 SHALL BE USED TO
<br />REDUCE THE RATE OF OUTDOOR AIR FLOW WHEN OCCUPANTS ARE NOT PRESENT, IN ACCORDANCE WITH 120.1(d)5.
<br />DUCTING FOR ZONAL HEATING AND COOLING UNITS. WHERE A RETURN PLENUM IS USED TO DISTRIBUTE OUTDOOR AIR
<br />TO A ZONAL HEATING OR COOLING UNIT WHICH THEN SUPPLIES THE AIR TO A SPACE IN ORDER TO MEET THE
<br />REQUIREMENTS OF SECTION 120.1(c)3, THE OUTDOOR AIR SHALL BE DUCTED TO DISCHARGE EITHER: WITHIN 5 FEET OF
<br />THE UNIT; OR WITHIN 15 FEET OF THE UNIT, SUBSTANTIALLY TOWARD THE UNIT, AND AT A VELOCITY NOT LESS THAN
<br />500 FEET PER MINUTE.
<br />NONRESIDENTIAL SYSTEMS NATURALLY VENTILATED SPACES SHALL BE DESIGNED IN ACCORDANCE WITH 120.1(c)2A
<br />THROUGH 120.1(c)2C AND SHALL ALSO INCLUDE MECHANICAL VENTILATION IN ACCORDANCE WITH 120.1(c)3.
<br />DESIGN AND CONTROL REQUIREMENTS FOR QUANTITIES OF OUTDOOR AIR. ALL MECHANICAL VENTILATION AND
<br />SPACE-CONDITIONING SYSTEMS SHALL BE DESIGNED WITH AND HAVE INSTALLED DUCTWORK, DAMPERS, AND
<br />CONTROLS TO ALLOW OUTSIDE AIR RATES TO BE OPERATED AT THE LARGER OF (1) THE MINIMUM LEVELS SPECIFIED IN
<br />SECTION 120.1(c)3 OR (2) THE RATE REQUIRED FOR MAKE-UP OF EXHAUST SYSTEMS THAT ARE REQUIRED FOR A
<br />PROCESS, FOR CONTROL OF ODORS, OR FOR THE REMOVAL OF CONTAMINANTS WITHIN THE SPACE.
<br />TIMES OF OCCUPANCY. THE MINIMUM RATE OF OUTDOOR AIR REQUIRED BY SECTION 120.1(c) SHALL BE SUPPLIED TO
<br />EACH SPACE AT ALL TIMES WHEN THE SPACE IS USUALLY OCCUPIED.
<br />SHUT-OFF AND RESET CONTROLS FOR SPACE-CONDITIONING SYSTEMS; SHALL BE INSTALLED WITH CONTROLS CAPABLE
<br />OF AUTOMATICALLY SHUTTING OFF THE SYSTEM DURING PERIODS OF NONUSE AND SHALL HAVE AN AUTOMATIC TIME
<br />SWITCH CONTROL DEVICE AND ACCESSIBLE MANUAL OVERRIDE THAT ALLOWS OPERATION OF THE SYSTEM FOR UP TO
<br />4 HOURS, AN OCCUPANCY SENSOR, OR A 4 HOUR TIMER THAT CAN BE MANUALLY OPERATED.
<br />ALL HEATING OR COOLING SYSTEMS NOT CONTROLLED BY A CENTRAL ENERGY MANAGEMENT CONTROL SYSTEM (EMCS)
<br />SHALL HAVE A SETBACK THERMOSTAT COMPLYING WITH 110.02c
<br />Fans (§120.10)
<br />EACH FAN OR FAN ARRAY WITH A COMBINED MOTOR NAMEPLATE HORSEPOWER GREATER THAN 1.00 HP OR WITH A
<br />COMBINED FAN NAMEPLATE ELECTRICAL INPUT POWER GREATER THAN 0.89 kW SHALL HAVE A FAN ENERGY INDEX (FEI)
<br />OF 1.00 OR HIGHER AT FAN SYSTEM DESIGN CONDITIONS. EACH FAN AND FAN ARRAY USED FOR A
<br />VARIABLE-AIR-VOLUME SYSTEM THAT MEETS THE REQUIREMENTS OF SECTION 140.4(c)2 SHALL HAVE AN FEI OF 0.95 OR
<br />HIGHER AT FAN SYSTEM DESIGN CONDITIONS.
<br />GENERAL NOTES
<br />1.
<br />REMOVABLE CEILING PANEL OR PANELS AT FACE OF ALL FIRE AND FIRE/SMOKE DAMPERS BY GENERAL
<br />CONTRACTOR (24" x 24" MIN.) UNLESS OTHERWISE NOTED.
<br />2.
<br />INCOMBUSTIBLE PLENUM ABOVE CEILING FOR RETURN/RECIRCULATING AIR BY GENERAL CONTRACTOR. CONCEALED
<br />BUILDING SPACES USED AS RETURN AIR PLENUMS SHALL BE IN COMPLIANCE WITH 2022 CMC 602.2.
<br />3.
<br />ACCESS DOORS AND/OR ACCESS PANELS THROUGH FIRE RATED WALLS, SHAFTS, CEILINGS, ETC., MUST EQUAL THE
<br />MATERIAL PENETRATED.
<br />4.
<br />ALL AIR SHAFTS SHALL BE MADE AIR TIGHT BY GENERAL CONTRACTOR.
<br />5.
<br />ALL UNDERCUT DOORS AND DOOR LOUVERS ARE BY GENERAL CONTRACTOR.
<br />6.
<br />ALL APPLIANCES DESIGNED TO BE FIXED IN POSITION SHALL BE SECURELY FASTENED IN PLACE.
<br />7.
<br />ALL SPACE CONDITIONING EQUIPMENT SHALL BE LABELED AS TO WHICH AREA IT SERVES.
<br />INSTALLATION OF SOFT-COPPER REFRIGERANT PIPING SHALL FOLLOW THE INTERPRETATION THAT CEILING
<br />STRUCTURES AND WALL STRUCTURES MEET THE REQUIREMENTS OF PIPING PROTECTION REQUIRED BY 2022 CMC
<br />1109.7
<br />8.
<br />EXCEPT AS MODIFIED BY A WRITTEN CONTRACT SIGNED BY THE DESIGN-BUILDER, THE DRAWINGS, SPECIFICATIONS,
<br />AND OTHER DOCUMENTS, INCLUDING THOSE IN ELECTRONIC FORM PREPARED BY OR FOR AND/OR FURNISHED BY
<br />DESIGN-BUILDER ARE “INSTRUMENTS OF SERVICE.” THE DESIGN-BUILDER, DESIGN-BUILDER'S CONSULTANTS AND
<br />OTHER PROVIDERS OF PROFESSIONAL SERVICES INDIVIDUALLY SHALL RETAIN A FULLY PREPAID, UNRESTRICTED,
<br />PERPETUAL LICENSE IN THE INSTRUMENTS OF SERVICE AS WELL AS ALL COMMON LAW, STATUTORY AND OTHER
<br />RESERVED RIGHTS, INCLUDING COPYRIGHT IN THOSE INSTRUMENTS OF SERVICE FURNISHED BY THEM.
<br />THE INSTRUMENTS OF SERVICE FURNISHED BY DESIGN-BUILDER ARE FOR SOLE USE BY DESIGN-BUILDER IN
<br />CONSTRUCTING THE SUBJECT PROJECT. THE INSTRUMENTS OF SERVICE ARE NOT SUITABLE FOR BIDDING OR
<br />CONSTRUCTING BY OTHER CONTRACTORS. THEREFORE, IF DESIGN-BUILDER IS NOT RETAINED AS THE DESIGN-BUILD
<br />CONTRACTOR TO PERFORM THE WORK DEPICTED IN THE INSTRUMENTS OF SERVICE, WITHOUT THE PRIOR WRITTEN
<br />CONSENT OF THE DESIGN BUILDER, THE INSTRUMENTS OF SERVICE MAY NOT BE REPRODUCED OR USED FOR ANY
<br />PURPOSE EXCEPT FOR GENERAL REFERENCE. DESIGN-BUILDER DISCLAIMS ALL LIABILITY FOR ANY ADAPTATION,
<br />MODIFICATION, OR INTERPRETATION OF THE INSTRUMENTS OF SERVICE, OR FOR ANY OTHER UNAUTHORIZED USE OF
<br />THESE INSTRUMENTS OF SERVICE.
<br />THESE DOCUMENTS WERE PREPARED FOR CONSTRUCTION BY DESIGN-BUILDER ONLY. DESIGN-BUILDER DEVELOPED
<br />THESE DOCUMENTS WITH ENGINEERING SOLUTIONS AND CONSTRUCTION MEANS AND METHODS UNIQUE TO
<br />DESIGN-BUILDER FOR THE CONSTRUCTION OF THE SUBJECT PROJECT AND ARE NOT APPROPRIATE FOR OTHERS TO
<br />BID OR BUILD FROM. IN ADDITION, THESE DRAWINGS WERE DEVELOPED FROM INFORMATION MADE KNOWN TO
<br />DESIGN-BUILDER AS OF THE DATE OF THE DOCUMENT AND WOULD NOT INCLUDE LATER CHANGES.
<br />9.
<br />10.
<br />PIPE INSULATION MINIMUM REQUIREMENTS (2019 & 2022)
<br />(PER TABLE 120.3-A PIPE INSULATION THICKNESS)
<br />SYSTEM
<br />FLUID
<br /> TEMPERATURE
<br /> RANGE (°F)
<br />CONDUCTIVITY
<br />RANGE (IN
<br />BTU-INCH PER HOUR
<br />PER SQUARE FOOT
<br />PER °F)
<br />INSULATION
<br />MEAN
<br />RATING
<br />TEMP. (°F)
<br />NOMINAL PIPE DIAMETER (INCHES)
<br /><1 1 TO <1.5 1.5 TO <4 4 TO <8 8 AND
<br />LARGER
<br />INSULATION THICKNESS REQUIRED (IN INCHES)
<br />SPACE HEATING AND SERVICE WATER HEATING SYSTEMS (STEAM, STEAM CONDENSATE, SPACE HEATING, SERVICE HOT WATER)
<br />HHW SYSTEM 141-200 0.25-0.29 125 1.5 1.5 2.0 2.0 2.0
<br />*2" AND LARGER PIPE FOR DOMESTIC HOT WATER WILL REQUIRE 2" INSULATION TO MEET 2022 CPC 609.12.2
<br />BOILER (GAS)
<br />TAG LOCATION MANUFACTURER &
<br />MODEL No.SERVING
<br />HEATING CAPACITY
<br />DUTY %DESIGN
<br />GPM
<br />MIN.
<br />GPM
<br />EWT
<br />(°F)
<br />LWT
<br />(°F)
<br />DPw
<br />(ft w.c.)
<br />CAT
<br />VENT VOLTAGE EMERGENCY
<br />POWER
<br />OPERATING
<br />WEIGHT (lbs)
<br />PRESSURE
<br />RATING
<br />(psi)
<br />REMARKSINPUT
<br />MBH
<br />OUTPUT
<br />MBH EFF.GAS PRESS.
<br />(in w.c.)
<br />TURNDOWN
<br />RATIO
<br />B-1 ROOF
<br />LOCHINVAR
<br />COPPER FIN II
<br />CHN0992
<br />HHW LOOP 990 842 85%4.5" - 14"4:1 100 80 29 160 180 -CAT I 120V-1ɸ N 773 160 FIELD INSTALLED, FACTORY PROVIDED INLINE PUMP, MODEL #:CF-0992-2072. 1/2 HP, ALL BRONZE, 90 GPM, 120V-1ɸ
<br />EQUIPMENT WEIGHT COMPARISON
<br />TAG EXISTING WEIGHT
<br />(lbs)
<br />REPLACEMENT WEIGHT
<br />(lbs)
<br />DIFFERENCE
<br />(lbs)
<br />DIFFERENCE
<br />(%)
<br />B-1 894 773 121 -13%
<br />D
<br />Scale
<br />Drawn By
<br />Job Number
<br />Designed By
<br />Title
<br />No.Date
<br />Project Manager
<br />Checked By
<br />Description By
<br />Project
<br />Revisions
<br />THE PLANS AND SPECIFICATIONS HEREIN
<br />ARE OWNED BY AND FOR THE SOLE USE OF
<br />ACCO ENGINEERED SYSTEMS, INC.
<br />(“ACCO”)THE "DESIGN BUILDER", AND MAY
<br />NOT BE REPRODUCED OR USED
<br />BY OTHERS FOR ANY PURPOSE UNLESS
<br />AUTHORIZED BY ACCO IN WRITING. ACCO
<br />CANNOT ACCEPT ANY LIABILITY, WARRANTY, OR
<br />OBLIGATION IN THE EVENT OF UNAUTHORIZED USE.
<br />X:
<br />\
<br />6
<br />0
<br />6
<br />5
<br />0
<br />2
<br />7
<br />7
<br />_
<br />O
<br />C
<br />
<br />P
<br />R
<br />O
<br />B
<br />A
<br />T
<br />I
<br />O
<br />N
<br />
<br />-
<br />
<br />1
<br />7
<br />0
<br />0
<br />\
<br />0
<br />1
<br />3
<br />-
<br />1
<br />0
<br />-
<br />E
<br />-
<br />H
<br />V
<br />A
<br />C
<br />\
<br />D
<br />W
<br />G
<br />\
<br />!
<br />B
<br />o
<br />i
<br />l
<br />e
<br />r
<br />
<br />R
<br />e
<br />p
<br />l
<br />a
<br />c
<br />e
<br />m
<br />e
<br />n
<br />t
<br />\
<br />6
<br />0
<br />6
<br />5
<br />0
<br />2
<br />7
<br />7
<br />_
<br />M
<br />_
<br />G
<br />E
<br />N
<br />E
<br />R
<br />A
<br />L
<br />
<br />S
<br />H
<br />E
<br />E
<br />T
<br />S
<br />20
<br />2
<br />5
<br />-
<br />0
<br />1
<br />-
<br />2
<br />7
<br />
<br />1
<br />0
<br />:
<br />2
<br />4
<br />
<br />A
<br />M
<br />Ke
<br />l
<br />s
<br />e
<br />y
<br />
<br />T
<br />h
<br />o
<br />m
<br />a
<br />s
<br />OC PROBATION
<br />BOILER REPLACEMENT
<br />1700 ST. ANDREW PL.
<br />SANTA ANA, CA 92705
<br />K. THOMAS M. LAYTON
<br />K. THOMAS J. PORTER
<br />60650277
<br />A 09-06-2024 ISSUE FOR PERMIT KMT
<br />265 McCORMICK AVENUE
<br />COSTA MESA, CALIFORNIA 92626
<br />(714) 352-2226
<br />CONSTRUCTION
<br />REQUIREMENTS &
<br />EQUIPMENT SCHEDULES
<br />NONE
<br />M0.01
<br />D 12-18-2024 REISSUE FOR PERMIT KMT
<br />EXP. 06/30/26
<br />No.M34053
<br />RE
<br />G
<br />ISTERED PROF E SSIONAL ENGINE
<br />ER
<br />STATE OF CALIFORNIAMECHANICAL
<br />MICHAEL G . LAYTON
<br />1700 E St Andrew Pl-
<br />Boiler4/16/2025
|