Laserfiche WebLink
The high-powered smart grid-ready IQ7HS <br />Microinverter with integrated MC4 connectors <br />dramatically simplifies the installation process while <br />achieving the highest system efficiency. <br />The IQ Series Microinverters extend the reliability <br />standards set forth by previous generations and <br />undergo over a million hours of power-on testing, <br />enabling Enphase to provide an industry-leading <br />warranty of up to 25 years. <br />IQ7HS Microinverter <br />To learn more about Enphase offerings, visit enphase.com <br />Data Sheet <br />Enphase Microinverter <br />Region: AMERICAS <br />Easy to Install <br />• Lightweight and simple <br />• Faster installation with improved, lighter two-wire cabling <br />• Built-in rapid shutdown compliant (NEC 2014 & 2017) <br />Efficient and Reliable <br />• Highest CEC efficiency of 97.0% <br />• More than a million hours of power-on testing <br />• Class II double-insulated enclosure <br />• UL listed <br />Smart Grid-Ready <br />• Complies with advanced grid support, voltage and <br />frequency ride-through requirements <br />• Remotely updates and responds to changing <br />grid-requirements <br />• Configurable for varying grid profiles <br />• Meets CA Rule 21 (UL1741-SA) <br />To learn more about Enphase offerings, visit enphase.com <br />© 2022 Enphase Energy. All rights reserved. All trademarks or brands used are the property of Enphase Energy, Inc. <br />12-12-2022 <br />INPUT DATA (DC) IQ7HS-66-M-US <br />Commonly used module pairings¹ 320W - 460W <br />Module compatibility² 66 cell/120 half-cell/132 half-cell <br />Maximum input DC voltage 59V <br />Peak power tracking voltage 38V - 43V <br />Operating range 20V - 59V <br />Min/Max start voltage 30V/59V <br />Max DC short circuit current (module Isc) 15A <br />Overvoltage class DC port II <br />DC port backfeed current 0A <br />PV array configuration 1 x 1 ungrounded array; No additional DC side protection required; <br />AC side protection requires max 20A per branch circuit <br />OUTPUT DATA (AC) @240 VAC @208 VAC <br />Peak output power 384 VA 369 VA <br />Maximum continuous output power 384 VA 369 VA <br />Nominal (L-L) voltage/range³ 240V/211-264V 208V/183-229V <br />Maximum continuous output current 1.60 A (240V) 1.77 A (208V) <br />Nominal frequency 60 Hz 60 Hz <br />Extended frequency range 47 Hz to 68 Hz 47 Hz to 68 Hz <br />AC short circuit fault current over 3 cycles 4.82 A 4.82 A <br />Maximum units per 20 A (L-L) branch circuit4 10 9 <br />Overvoltage class AC port III III <br />AC port backfeed current 18 mA 18 mA <br />Power factor setting 1.0 1.0 <br />Power factor (adjustable) 0.85 leading ...0.85 lagging 0.85 leading ...0.85 lagging <br />EFFICIENCY @240V @208V <br />CEC weighted efficiency 97.0 % 96.5 % <br />MECHANICAL DATA <br />Ambient temperature range <br />Relative humidity range <br />Connector type <br />Dimensions (WxHxD) <br />Weight <br />Cooling <br />Approved for wet locations <br />Pollution degree <br />Enclosure <br />Environmental category / UV exposure rating <br />Altitude <br />-40ºC to +60ºC <br />4% to 100% (condensing) <br />Staubli made MC4 <br />212 mm x 175 mm x 30.2 mm (without bracket) <br />1.08 kg (2.38 lbs) <br />Natural convection - No fans <br />Yes <br />PD3 <br />Class II, corrosion resistant polymeric enclosure <br />NEMA type 6/outdoor <br />2000m <br />FEATURES <br />Communication Power Line Communication (PLC) <br />Disconnecting means The AC and DC connectors have been evaluated and approved by UL for use as the load-break <br />disconnect means required by NEC 690 and C22.1-2018 Rule 64-220. <br />Compliance CA Rule 21 (UL1741-SA), HECO v1.1 <br />UL62109-1, UL1741/IEEE1547, FCC Part 15 Class B, ICES-0003 Class B, <br />CAN/CSA-C22.2 NO. 107.1-01 <br />This product is UL Listed as PV Rapid Shut Down Equipment and conforms with NEC-2014 and <br />NEC-2017 section 690.12 and C22.1-2015 Rule 64-218 Rapid Shutdown of PV Systems, for AC <br />and DC conductors, when installed according to manufacturer’s instructions. <br />1. No enforced DC/AC ratio. See the compatibility calculator at https://enphase.com/en-us/support/module-compatibility. <br />2. Provided the module is compatible with all other parameters in the datasheet. <br />3. Nominal voltage range can be extended beyond nominal if required by the utility. <br />4. Limits may vary. Refer to local requirements to define the number of microinverters per branch in your area. <br />IQ7HS Microinverter <br />1906 E Kemper <br />Ave02/15/23