Laserfiche WebLink
Wood Column <br />LIC# : KW-06016886, Build:20.23.12.07 LEE & LEE STRUCTURAL ENGINEERING INC.(c) ENERCALC INC 1983-2023 <br />DESCRIPTION:Stud (R) 2X6 <br />Project File: 201 W 19th St.ec6 <br />Project Title: <br />Engineer: <br />Project ID: <br />Project Descr: <br />.Code References <br />Calculations per NDS 2018, IBC 2018, CBC 2019, ASCE 7-16 <br />Load Combinations Used : IBC 2021 <br />General Information <br />Wood Section Name 2x6Analysis Method : <br />13Overall Column Height ft <br />Allowable Stress Design <br />( Used for non-slender calculations )Allow Stress Modification Factors <br />End Fixities Top & Bottom Pinned <br />Wood Species Douglas Fir-Larch <br />Wood Grade No.2 <br />Fb +900 <br />900 psi <br />1350 <br />625 <br />180 <br />575 <br />31.21 <br />psi Fv psi <br />Fb -Ft psi <br />Fc - Prll psi <br />psi <br />Density pcf <br />Fc - Perp <br />E : Modulus of Elasticity . . . <br />1600 <br />580 <br />1600 <br />580 <br />Cfu : Flat Use Factor 1.0 <br />Cf or Cv for Tension 1.30 <br />Use Cr : Repetitive ? <br />Kf : Built-up columns 1.0 <br />Exact Width 1.50 in <br />Exact Depth 5.50 in <br />Area 8.250 in^2 <br />Ix 20.797 in^4 <br />Iy 1.547 in^4 <br />Wood Grading/Manuf.Graded Lumber <br />Wood Member Type Sawn <br />Ct : Temperature Factor 1.0 <br />Cf or Cv for Compression 1.10 <br />1600 <br />Axial <br />Cm : Wet Use Factor 1.0 <br />Cf or Cv for Bending 1.30 <br />x-x Bending y-y Bending <br />ksi No <br />Minimum <br />Basic <br />Fully braced against buckling ABOUT Y-Y Axis <br />ABOUT X-X Axis: Lux = 13 ft, Kx = 1.0 <br />Column Buckling Condition: <br />.Service loads entered. Load Factors will be applied for calculations.Applied Loads <br />Column self weight included : 23.245 lbs * Dead Load Factor <br />AXIAL LOADS . . . <br />Roof: Axial Load at 13.0 ft, D = 0.3460, L = 0.6210 k <br />Floor: Axial Load at 13.0 ft, D = 0.2330, L = 0.7760 k <br />BENDING LOADS . . . <br />Wind: Lat. Uniform Load creating Mx-x, W = 0.02128 k/ft <br />.DESIGN SUMMARY <br />PASS <br />PASS <br />Max. Axial+Bending Stress Ratio =0.5366 <br />Location of max.above base 6.456 ft <br />Applied Axial 1.650 k <br />Applied Mx 0.2023 k-ft <br />Load Combination +D+0.750L+0.450W <br />Load Combination +D+0.60W <br />Bending & Shear Check Results <br />Maximum Shear Stress Ratio = <br />Applied Design Shear 22.634 psi <br />288.0Allowable Shear psi <br />0.05239 : 1 Bending Compression Tension <br />Location of max.above base 13.0 ft <br />: 1 <br />At maximum location values are . . . <br />Applied My 0.0 k-ft <br />Maximum SERVICE Lateral Load Reactions . . <br />Top along Y-Y 0.1383 k Bottom along Y-Y 0.1383 k <br />Top along X-X 0.0 k Bottom along X-X 0.0 kGoverning NDS Forumla Comp + Mxx, NDS Eq. 3.9-3 <br />Maximum SERVICE Load Lateral Deflections . . . <br />Along Y-Y 0.4154 in at 6.544 ft above base <br />for load combination :W Only <br />Along X-X 0.0 in at 0.0 ft above base <br />Fc : Allowable 558.32 psi <br />Other Factors used to calculate allowable stresses . . . <br />for load combination :n/a <br />. <br />Maximum Axial + Bending Stress Ratios Maximum Shear RatiosCDCLoad Combination Stress Ratio Location Stress Ratio Status LocationPStatus <br />Load Combination Results <br />D Only 0.900 PASS PASS0.0 0.0 13.0 ft0.393 ft0.1391 <br />+D+L 1.000 PASS PASS0.0 0.0 13.0 ft0.359 ft0.4547 <br />+D+0.750L 1.250 PASS PASS0.0 0.0 13.0 ft0.295 ft0.3657 <br />+D+0.60W 1.600 PASS PASS6.544 0.05239 13.0 ft0.235 ft0.4284 <br />+D+0.750L+0.450W 1.600 PASS PASS6.456 0.03930 0.0 ft0.235 ft0.5366 <br />+0.60D+0.60W 1.600 PASS PASS6.544 0.05239 13.0 ft0.235 ft0.3956 <br />+0.60D 1.600 PASS PASS0.0 0.0 13.0 ft0.235 ft0.07845 <br />. <br />39 of 81 <br />210 W 19th St <br />4/14/2025