|
FIG. (B)FIG. (A)
<br />PROPORTIONS
<br />SYMBOL
<br />MEN
<br />11B-703.7.2.2
<br />ISA OF TTY
<br />INTERNATIONAL SYMBOL
<br />INTERNATIONAL SIGN
<br />FOR HEARING LOSS
<br />INTERNATIONAL ACCESSIBILITY
<br />40
<br />"
<br />
<br />M
<br />A
<br />X
<br />.
<br />
<br />T
<br />O
<br />
<br />R
<br />E
<br />F
<br />L
<br />E
<br />C
<br />T
<br />I
<br />V
<br />E
<br />
<br />S
<br />U
<br />R
<br />F
<br />A
<br />C
<br />E
<br />6" MAX.
<br />ELEVATIONSB
<br />NOTE:
<br />54" PREFERRED
<br />DOOR WIDTH PLUS
<br />1.
<br />DOOR TYPE:
<br />3.
<br />2.
<br />HARDWARE:
<br />EITHER ATTACHED PANEL OR BOTTOM RAIL.
<br />KNOWLEDGE OR EFFORT.
<br />4.
<br />5.
<br />REQUIRING GRASPING).
<br />MOUNTED 34" TO 44".
<br />5 LBS. FOR INTERIOR.
<br />MINIMUM 10" HIGH SMOOTH SURFACE AT DOOR BOTTOM,
<br />OPENABLE FROM INSIDE WITHOUT USE OF KEY OR SPECIAL
<br />OPENABLE BY SINGLE EFFORT LEVER-TYPE DEVICE (NOT
<br />MAXIMUM 5 LBS. EFFORT TO OPERATE EXTERIOR DOOR,
<br />HANDLE
<br />KICK PLATE
<br />34" TO 44" HIGH LEVER
<br />10" MIN. BOTTOM
<br />RAIL OR PROVIDE
<br />RUBBER BUMPER ON CHAIR
<br />OR WALL OCCURS
<br />12" MINIMUM IF DOOR HAS
<br />WHERE ADJACENT OBSTRUCTION
<br />BOTH A CLOSER AND A LATCH
<br />REQUIRED CLEAR SPACE
<br />48" MINIMUM
<br />REQUIRED CLEAR SPACE
<br />24" MIN. EXTERIOR
<br />18" MIN. INTERIOR
<br />B CORRIDOR PLAN
<br />18" MIN.
<br />INTERIOR
<br />EXTERIOR
<br />24" MIN.
<br />OF BLDG.
<br />PLANA
<br />SWINGS.
<br />24" MIN. EXTERIOR &
<br />18" MINIMUM INTERIOR
<br />BEYOND STRIKE EDGE OF A
<br />GATE OR DOOR ON THE
<br />SIDE TOWARD WHICH IT
<br />18" MIN. INTERIOR
<br />24" MIN. EXTERIOR
<br />A HIGH FORWARD REACH LIMIT
<br />1.
<br />3.
<br />2.
<br />NOTES:
<br />B
<br />X SHALL BE < 25 INCHES; Z SHALL BE > X.
<br />WHEN X < 20 INCHES, THEN Y SHALL BE 48 INCHES MAXIMUM.
<br />WHEN X IS 20 TO 25 INCHES, THEN Y SHALL BE 44 INCHES MAXIMUM.
<br />MAXIMUM FORWARD REACH OVER AN OBSTRUCTION
<br />C VESTIBULE PLANB
<br />RAMP LANDING AT
<br />DOORWAY PLAN
<br />NOTES:
<br />1. CLEAR SPACES MUST BE LEVEL TO PREVENT WHEELCHAIRS FROM ROLLING WHEN THE OCCUPANT
<br />RELEASES THE WHEEL GRIPS TO REACH FOR THE DOOR. 1/4" PER FOOT IS ALLOWED FOR DRAINAGE.
<br />2. WHERE DOORS OPEN ONTO, BUT NOT INTO A CORRIDOR, THE REQUIRED LEVEL AREA BEYOND THE
<br />DOORS MAY BE A MINIMUM OF 48". FOR ADDITIONAL INFORMATION, SEE APPLICABLE NOTES ON
<br />TYPICAL ACCESSILIBITY NOTES SHEET.
<br />D
<br />SIDE REACH LIMITS
<br />HIGH AND LOWCCLEAR FLOOR SPACE
<br />PARALLEL APPROACH
<br />E
<br />MAXIMUM SIDE REACH
<br />CLEAR WIDTH
<br />MAX.
<br />CANE RANGE
<br />FIN. FLOOR LEVEL
<br />THRESHOLD
<br />2
<br />FIG. (A)
<br />A
<br />1/2" MAX.
<br />PILE HEIGHT
<br />TRANSITION BETWEEN FLOOR FINISHES
<br />COMPRESSED CARPET 1/4" MAX.
<br />BELOW THRESHOLD
<br />CANE RANGE
<br />1/2" MAX.
<br />1/4" MAX.
<br />THRESHOLD
<br />LEVEL CHANGES
<br />B
<br />C
<br />2.
<br />1.
<br />3.
<br />NOTES:
<br />CHANGE AT EDGE.
<br />1/2" MAXIMUM TOTAL HEIGHT WITH 1/4" MAXIMUM VERTICAL
<br />1 : 2 SLOPED BEVEL REQUIRED IF LEVEL CHANGE IS OVER
<br />1/4" MAXIMUM VERTICAL LEVEL CHANGE.
<br />1/4" VERITCAL LEVEL CHANGE.
<br />1
<br />ANY AMOUNT
<br />CANE HITS POST OR PYLON
<br />BEFORE PERSON HITS OBJECT
<br />OVER AN OBSTRUCTION
<br />MIN
<br />MIN
<br />MIN
<br />MAX.
<br />36" MAX.
<br />24" MIN.
<br />7"-9"
<br />33
<br />"
<br />-
<br />3
<br />6
<br />"
<br />TO
<br />
<br />T
<br />O
<br />P
<br />40
<br />"
<br />
<br />M
<br />A
<br />X
<br />.
<br />34
<br />"
<br />
<br />M
<br />A
<br />X
<br />.
<br />29
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />27
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />9"
<br />
<br />M
<br />I
<br />N
<br />.
<br />17"MIN.-19"MAX.
<br />11" MIN.
<br />MA
<br />X
<br />MAX
<br />30"24"
<br />34
<br />"
<br />
<br />M
<br />A
<br />X
<br />.
<br />46
<br />"
<br />
<br />M
<br />A
<br />X
<br />.
<br />19"
<br />34
<br />"
<br />
<br />M
<br />A
<br />X
<br />.
<br />27
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />48"MIN.
<br />48"
<br />48
<br />"
<br />15
<br />"
<br />M
<br />I
<br />N
<br />.
<br />MIN
<br />X
<br />48"
<br />Z
<br />Y
<br />HI
<br />G
<br />H
<br />E
<br />R
<br />
<br />T
<br />H
<br />A
<br />N
<br />LETTERS AND NUMBERS:
<br />1. WIDTH TO HEIGHT RATIO BETWEEN 3 : 5 AND 1 : 1.
<br />2. STROKE WIDTH TO HEIGHT BETWEEN 1 : 5 AND 1 : 10.
<br />3. CONTRAST CHARACTERS AND SYMBOLS WITH BACKGROUND.
<br />4. SANS SERIF CHARACTERS.
<br />SIGNS:
<br />5. PICTOGRAMS / PICTORIAL SYMBOL SIGNS SHALL BE ACCOMPANIED BY
<br />THE EQUIVALENT VERBAL DESCRIPTION PLACED DIRECTLY BELOW THE
<br />PICTOGRAM. THE BORDER DIMENSION SHALL BE 6" MINIMUM HEIGHT.
<br />6. CHARACTERS AND BACKGROUNDS SHALL BE OF NON-GLARE
<br />CONTRASTING COLORS.
<br />7. SIGNS/PICTOGRAMS SHALL BE INSTALLED ON THE LATCH SIDE OF THE
<br />DOOR LEADING TO THE ROOM OF SPACE THEY DESCRIBE AND WITH A
<br />CLEAR FLOOR SPACE OF 18"x18" CENTERED ON THE TACTILE
<br />CHARACTERS BEYOND DOOR ARC BETWEEN 45 DEGREES AND CLOSED.
<br />LOCATE ABOVE THE FLOOR PER DETAIL 1/AD1
<br />8. VERTICAL CLEARANCE AT SUSPENDED SIGNS WITH MINIMUM
<br />HEADROOM OF 80" REQUIRE MINIMUM 3" CHARACTER HEIGHT
<br />MEASURED BY USING UPPER CASE "X". CHARACTERS AND NUMBERS
<br />SHALL BE SIZED ACCORDING TO VIEWING DISTANCE FROM WHICH
<br />READ. LOWER CASE CHARACTERS PERMITTED.
<br />SIGN LOCATIONS:
<br />9. ALL ACCESSIBLE ENTRANCES IDENTIFIED WITH MINIMUM OF ONE
<br />STANDARDS SIGN.
<br />10. ADDITIONAL DIRECTIONAL SIGNS ALONG ACCESSIBLE PATH OF TRAVEL
<br />ARE REQUIRED.
<br />11. BUILDINGS REMODELED TO PROVIDE ACCESSIBLE SANITARY FACILITIES
<br />FOR PUBLIC USE SHALL HAVE INFORMATION POSTED IN THE LOBBY AS
<br />PART OF THE BUILDING DIRECTORY.
<br />INTERNATIONAL SYMBOL OF ACCESSILITY:
<br />12. STANDARD USED TO IDENTIFY ACCESSIBLE FACILITIES.
<br />13. WHITE FIGURE ON BLUE BACKGROUND, COLOR # 15090 ON FEDERAL
<br />STANDARD # 595C.
<br />14. WHEN ENFORCING AGENCY DETERMINES, IF APPROPRIATE, SPECIAL
<br />DESIGNS AND COLORS MAY BE APPROVED.
<br />BRAILLE:
<br />15. USE CONTRACTED GRADE 2 BRAILLE. DOTS TO BE 0.1" ON CENTER IN
<br />EACH CELL.
<br />16. 0.2" SPACE BETWEEN CELLS.
<br />17. DOTS RAISED MINIMUM 0.025" ABOVE BACKGROUND.
<br />18. CHARACTERS SHALL BE SANS SERIF UPPER CASE ACCOMPANIED BY
<br />GRADE 2 BRAILLE ANS SIZED
<br />OF ACCESSIBILITY
<br />OF ACCESS
<br />PLANA
<br />TOILET ROOM SIGNAGE
<br />DISABLED ACCESSIBILITY
<br />TO COMPLY WITH TITLE 24
<br />12"
<br />TYP.
<br />58
<br />"
<br />-
<br />6
<br />0
<br />"
<br />REQUIREMENTS TO
<br />
<br />C
<br />E
<br />N
<br />T
<br />E
<br />R
<br />
<br />O
<br />F
<br />
<br />S
<br />I
<br />G
<br />N
<br />GEOMETRIC SYMBOLS
<br />12"
<br />TYP.
<br />6"
<br />M
<br />I
<br />N
<br />.
<br />11B-703.6.1
<br />PICTOGRAM FIELD
<br />11B-703.7.2.4
<br />VOLUME CONTROL TELEPHONE
<br />11B-703.7.2.3
<br />8" MIN.
<br />36" (MIN.) GRAB BARS
<br />FLUSH ACTIVATOR
<br />ON WIDE SIDE
<br />48" MIN. WHEN FRONT
<br />ENTRY DOOR OR 60"MIN.
<br />WHEN SIDE ENTRY DOOR
<br />- WATER CLOSET SHALL BE "ULTRA LOW FLUSH"
<br />TYPE WITH 1.6 GALLONS MAXIMUM PER FLUSH.
<br />-TOILET ROOMS SHALL BE FINISHED WITH TILE OR
<br />MARLITE OVER MOISTURE BE RESISTANT DRYWALL
<br />TO A MINIMUM HEIGHT OF 4'-0" WITH 6" MIN. BASE
<br />42" GRAB BAR
<br />ALL SIGNS SHALL COMPLY WITH SECTION 11B-703, DIVISION 7, CHAPTER 11B OF CBC 2022
<br />60" DIA.
<br />17
<br />"
<br />MI
<br />N
<br />.
<br />18"
<br />MIN.
<br />30"x48"
<br />MIN. CLR.
<br />FLR. SPACE
<br />19
<br />"
<br />MA
<br />X
<br />.
<br />24"
<br />MIN.
<br />12"
<br />MIN.
<br />17"-18"
<br />CL
<br />60' MIN.
<br />24
<br />"
<br />MI
<br />N
<br />.
<br />48
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />59
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />4"
<br />MAX.
<br />.19
<br />"
<br />MI
<br />N
<br />.
<br />TOILET SEAT DISPENSER
<br />(WHERE OCCURS)
<br />1-1/2" DIAMETER GRAB
<br />BAR W/ PEENED FINISH &
<br />250 LBS. CAPACITY
<br />17" TO 18" TO
<br />TOP OF TOILET SEAT
<br />ROLL PAPER HOLDER
<br />WITHOUT STOPS
<br />PROVIDE PRIVACY DOOR LOCK WHEN IT
<br />IS A PRIVATE TOILET OR FOR UNISEX USE.
<br />32" CLR.
<br />CBC 11B-703.7.2.1
<br />12
<br />"
<br />
<br />M
<br />A
<br />X
<br />MEN MEN
<br />UNISEX
<br />15
<br />"
<br />30"
<br />48
<br />"48
<br />"
<br />30
<br />"
<br />48"
<br />30
<br />"
<br />48"
<br />Z
<br />X
<br />80
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />27
<br />"
<br />M
<br />I
<br />N
<br />.
<br />27
<br />"
<br />M
<br />I
<br />N
<br />.
<br />27
<br />"
<br />M
<br />I
<br />N
<br />.
<br />27
<br />"
<br />M
<br />I
<br />N
<br />.
<br />12"
<br />MAX.
<br />60
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />
<br />4
<br />8
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />36" MIN.
<br />48
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />48" MIN.
<br />32" CLEAR
<br />DO
<br />O
<br />R
<br />
<br />W
<br />I
<br />D
<br />T
<br />H
<br />
<br />P
<br />L
<br />U
<br />S
<br />
<br />4
<br />2
<br />"
<br />48
<br />"
<br />
<br />M
<br />I
<br />N
<br />.
<br />4"
<br />THE 2022 CALIFORNIA BUILDING CODE CHAPTER 11B FOR
<br />ACCESSIBLE PARKING STANDARDS FOR COMMERCIAL BUILDINGS &
<br />PUBLIC ACCOMMODATIONS. FOR ADDITIONAL PARKING
<br />REGULATIONS PLEASE REFER TO THE LOCAL MUNICIPAL CODE FOR
<br />THE REQUIREMENTS.
<br />ACCESSIBLE PARKING
<br />1. PARKING SPACES COMPLYING WITH SECTION 11B-502 THAT
<br />SERVE A PARTICULAR BUILDING OR FACILITY SHALL BE LOCATED ON
<br />THE SHORTEST ACCESSIBLE ROUTE FROM PARKING TO AN
<br />ENTRANCE COMPLYING WITH SECTION 11B-206.4. WHERE PARKING
<br />SERVES MORE THAN ONE ACCESSIBLE ENTRANCE, PARKING SPACES
<br />COMPLYING WITH SECTION 11B-502 SHALL DISPERSED AND
<br />LOCATED ON THE SHORTEST ACCESSIBLE ROUTE TO THE
<br />ACCESSIBLE ENTRANCES. IN PARKING FACILITIES THAT DO NOT
<br />SERVE A PARTICULAR BUILDING OR FACILITY, PARKING SPACES
<br />COMPLYING WITH SECTION 11B-502 SHALL BE LOCATED ON THE
<br />SHORTEST ACCESSIBLE ROUTE TO AN ACCESSIBLE PEDESTRIAN
<br />ENTRANCE OF THE PARKING FACILITY. (PER 11B-208.3.1)
<br />SURFACES SLOPES OF ACCESSIBLE PARKING SPACES
<br />1. 11B-405.2 SLOPE - RAMP RUNS SHALL HAVE A RUNNING SLOPE
<br />NOT STEEPER THAN 1:12.
<br />2. 11B.405.3 CROSS SLOPE - CROSS SLOPE OF RAMP RUNS
<br />SHALL NOT BE STEEPER THAN 1:48
<br />3. 11B-405.6 RISE - THE RISE OF ANY RAMP RUN SHALL BE 30"
<br />MAXIMUM.
<br />PARKING SPACE AND SIGNAGE
<br />1. CAR AND VAN PARKING SPACES SHALL COMPLY WITH SECTION
<br />11B-502. WHERE PARKING SPACES ARE MARKED WITH LINES,
<br />WITH MEASUREMENTS OF PARKING SPACES AND ACCESS
<br />AISLES SHALL BE MADE FROM THE CENTERLINE OF THE
<br />MARKINGS (PER 11B-501.1).
<br />2. CAR AND VAN PARKING SPACES SHALL BE 18' LONG MIN. CAR
<br />PARKING SPACES SHALL BE 9' WIDE MIN. AND VAN PARKING
<br />SPACES SHALL BE 12' WIDE MINIMUM, SHALL BE MARKED TO
<br />DEFINED THE WIDTH, AND SHALL HAVE AN ADJACENT ACCESS
<br />AISLE COMPLYING WITH SECTION 11B-502.3. (PER
<br />11B-502.2).
<br />3. ACCESS AISLES SERVING PARKING SPACES SHALL COMPLY WITH
<br />SECTION 11B-502.3. ACCESS AISLES SHALL ADJOIN AN
<br />ACCESSIBLE ROUTE. TWO PARKING SPACES SHALL BE
<br />PERMITTED TO SHARE A COMMON ACCESS AISLE. (PER
<br />11B-502.3).
<br />WIDTH - ACCESS AISLE SERVING CAR AND VAN PARKING SPACE
<br />SHALL BE 60" WIDE MINI.
<br />LENGTH - ACCESS AISLE SHALL EXTEND THE FULL REQUIRED
<br />LENGTH OF THE PARKING SPACES THEY SERVE.
<br />(PER11B-502.3.2).
<br />MARKING - ACCESS AISLE SHALL BE MARKED WITH A BLUE
<br />PAINTED BORDERLINE AROUND THEIR PERIMETER. THE AREA
<br />WITHIN THE BLUE BORDERLINES SHALL BE MARKED WITH
<br />HATCHED LINES A MAX. OF 36" ON CENTER IN A COLOR
<br />CONTRASTING WITH THAT OF THE AISLE SURFACE, PREFERABLY
<br />BLBLUE OR WHITE. THE WORDS "NO PARKING" SHALLE BE
<br />PAINTED ON THE SURFACE WITHIN ACCESS AISLE IN WHITE
<br />LETTERS A MIN. OF 12" IN HEIGHT & LOCATED TO BE VISIBLE
<br />FROM THE ADJACENT VEHICULAR WAY. ACCESS AISLE
<br />MARKINGS MAY EXTEND BEYOND THE MINIMUM REQUIRED
<br />LENGTH. (PER 11B-502.3.3)
<br />4. PARKING SPACE IDENTIFICATION SIGNS SHALL INCLUDE THE
<br />INTERNATIONAL SYMBOL OF ACCESSIBILITY COMPLYING WITH
<br />SECTION 11B-703.7.2.1. SIGNS IDENTIFYING VAN PARKING
<br />SPACES SHALL CONTAIN ADDITIONAL LANGUAGE OR AN
<br />ADDITIONAL SIGN WITH THE DESIGNATION "VAN ACCESSIBLE."
<br />SIGNS SHALL BE 60" MIN. ABOVE FINISH FLOOR OR GROUND
<br />SURFACE MEASURED TO THE BOTTOM OF THE SIGN. FINISH AND
<br />SIZE - PARKING IDENTIFICATION SIGNS SHALL BE REFLECTORIZED
<br />WITH A MIN. AREA OF 70 SQUARE INCHES. (PER 11B-502.6.1).
<br />MINIMUM FINE - ADDITIONAL LANGUAGE OR AN ADDITIONAL
<br />SIGN BELOW THE INTERNATIONAL SYMBOL OF ACCESSIBILITY
<br />SHALL STATE "MINIMUM FINE $250." (PER 11B-520.6.2).
<br />LOCATION - A PARING SPACE IDENTIFICATION SIGN SHALL BE
<br />VISIBLE FROM EACH PARKING SPACE. SIGNS SHALL BE
<br />PERMANENTLY POSTED EITHER IMMEDIATELY ADJACENT TO THE
<br />PARKING SPACE OR WITHIN THE PROTECTED PARKING SPACE
<br />WIDTH AT THE HEAD END OF THE PARKING SPACE. SIGNS MAY
<br />ALSO BE PERMANENTLY POSTED ON A WALL AT THE INTERIOR
<br />END OF THE PARKING SPACE. (PER 11B-502.6.3)
<br />5. EACH ACCESSIBLE CAR AND VAN SPACE SHALL HAVE SURFACE
<br />IDENTIFICATION COMPLYING WITH EITHER SECTIONS
<br />11B-502.6.4.1 OR 11B-502.6.4.2. (PER 11B-502.6.4.1)
<br />THE PARKING SPACE SHALL BE MARKED WITH AN INTERNATIONAL
<br />SYMBOL OF ACCESSIBILITY (ISA) COMPLYING WITH SECTION
<br />11B-703.7.2.1IN WHITE ON A BLUE BACK GROUND A MINIMUM
<br />36" WIDE BY 36" HIGH. THE CENTER LINE OF ISA SHALL BE A
<br />MAXIMUM OF 6" FROM THE CENTER LINE OF THE PARKING
<br />SPACE, ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING
<br />SPACE AND ITS LOWER CORNER AT, OR LOWER SIDE ALIGNED
<br />WITH, THE END OF THE PARKING SPACE LENGTH.
<br />(11B-502.6.4.1)
<br />THE PARKING SPACE SHALL BE OUTLINED OR PAINTED BLUE AND
<br />SHALL BE MARKED WITH AN ISA COMPLYING WITH SECTION
<br />11B-703.7.2.1 A MIN. 36" WIDE BY 36" HIGH IN WHITE OR A
<br />SUITABLE CONTRASTING COLOR. THE CENTERLINE OF THE ISA
<br />SHALL BE A MAX. OF 6" FROM THE CENTERLINE OF THE PARKING
<br />SPACE, ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING
<br />SPACE AND ITS LOWER CORNER AT, OR LOWER SIDE ALIGNED
<br />WITH, THE END OF THE PARKING SPACE (PER 11B-502.6.4.2).
<br />6. AN ADDITIONAL SIGN SHALL BE POSTED EITHER;
<br />1) IN A CONSPICUOUS PLACE AT EACH ENTRANCE TO AN OFF-
<br />STREET PARKING FACILITY OR
<br />2) IMMEDIATELY ADJACENT TO ON-SITE ACCESSIBLE PARKING
<br />AND VISIBLE FROM EACH PARKING SPACE. (PER 11B-502.8)
<br />THE SIZE OF ADDITIONAL SIGN SHALL NOT BE LESS THAN 17"
<br />WIDE BY 22" HIGH. (PER 11B-502.8.1) THE LETTER OF
<br />ADDITIONAL SIGN SHALL CLEARLY STATE IN LETTERS WITH A
<br />MINIMUM HEIGHT OF 1" THE FOLLOWING:
<br />
<br />"UNAUTHORIZED VEHICLES PARKED IN DESIGNATED ACCESSIBLE
<br />SPACE NOT DISPLAYING DISTINGUISHING PLACARDS OR SPECIAL
<br />LICENSE PLATES ISSUED FOR PERSONS WITH DISABILITIES WILL
<br />BE TOWED AWAY AT THE OWNER'S EXPENSE. TOWED VEHICLES
<br />MAY BE RECLAIMED AT: _____ OR BY TELEPHONING ______."
<br />BLANK SPACES SHALL BE FILLED IN WHICH APPROPRIATE
<br />INFORMATION AS A PERMANENT PART OF THE SIGN. (PER
<br />11B-502.8.2)
<br />VERTICAL CLEARANCE
<br />1. PARKING SPACES, ACCESS AISLES AND VEHICULAR ROUTES
<br />SERVING THEM SHALL PROVIDE A VERTICAL CLEARANCE 98"
<br />MINIMUM. (PER 11B-502.6)
<br />E
<br />KNEE CLEARANCE
<br />AT DINING TABLE
<br />VAN PARKING SPACES
<br />1. FOR EVERY SIX OR FRACTION OF SIX PARKING SPACES REQUIRED
<br />BY SECTION 11B-208.2 TO COMPLY WITH SECTION 11B-502, AT
<br />LEAST ONE SHALL BE A VAN PARKING SPACE COMPLYING WITH
<br />SECTION 11B-502. (PER 11B-208.2.4).
<br />EACH ACCESSIBLE CAR AND VAN SPACE SHALL HAVE SURFACE
<br />IDENTIFICATION COMPLYING WITH EITHER SECTION 11B-502.6.4 OR
<br />11B-502.6.4.2.
<br />1. THE PARKING SPACE SHALL BE MARKED WITH AN
<br />INTERNATIONAL SYMBOL OF ACCESSIBILITY COMPLYING
<br />WITH SECTION 11B-703-.7.2.1 IN WHITE ON A BLUE
<br />BACKGROUND A MINIMUM 36" WIDE BY 36" HIGH. THE
<br />CENTERLINE OF THE INTERNATIONAL SYMBOL OF
<br />ACCESSIBILITY SHALL BE A MAXIMUM OF 6" FROM THE
<br />CENTERLINE OF THE PARKING SPACE, ITS SIDES PARALLEL
<br />TO THE LENGTH OF THE PARKING SPACE AND ITS LOWER
<br />CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF
<br />THE PARKING SPACE LENGTH. (PER 11B-502.6.4)
<br />2. THE PARKING SPACE SHALL BE OUTLINED OR PAINTED BLUE
<br />AND SHALL BE MARKED WITH AN INTERNATIONAL SYMBOL
<br />OF ACESSIBILITY (ISA) COMPLYING WITH SECTION
<br />11B-7037.2.1 A MINIMUM 36" WIDE BY 36" HIGH IN
<br />WHITE OR A SUITABLE CONTRASTING COLOR. THE CENTER
<br />LINE OF ISA SHALL BE A MINIMUM OF 6" FROM THE CENTER
<br />OF PARKING SPACE, ITS SIDES PARALLEL TO THE LENGTH OF
<br />THE PARKING SPACE & LOWER CORNER AT, OR LOWER SIDE
<br />ALIGNED WITH, THE END OF THE PARKING SPACE. (PER
<br />11B-502..6.4.2)
<br />AN ADDITIONAL SIGN SHALL BE POSTED EITHER;
<br />1) IN A CONSPICUOUS PLACE AT EACH ENTRANCE TO AN OFF-
<br />STREET PARKING FACILITY OR
<br />2) IMMEDIATELY ADJACENT TO ON-SITE ACCESSIBLE PARKING
<br />AND VISIBLE FROM EACH PARKING SPACE. (PER 11B-502.8)
<br />THE SIZE OF ADDITIONAL SIGN SHALL NOT BE LESS THAN 17"
<br />WIDE BY 22" HIGH. (PER 11B-502.8.1) THE LETTER OF
<br />ADDITIONAL SIGN SHALL CLEARLY STATE IN LETTERS WITH A
<br />MINIMUM HEIGHT OF 1" THE FOLLOWING:
<br />
<br />"UNAUTHORIZED VEHICLES PARKED IN DESIGNATED ACCESSIBLE
<br />SPACE NOT DISPLAYING DISTINGUISHING PLACARDS OR SPECIAL
<br />LICENSE PLATES ISSUED FOR PERSONS WITH DISABILITIES WILL
<br />BE TOWED AWAY AT THE OWNER'S EXPENSE. TOWED VEHICLES
<br />MAY BE RECLAIMED AT: _____ OR BY TELEPHONING ______."
<br />BLANK SPACES SHALL BE FILLED IN WHICH APPROPRIATE
<br />INFORMATION AS A PERMANENT PART OF THE SIGN. (PER
<br />11B-502.8.2)
<br />WALKS & SIDEWALKS:
<br />GENERAL. WALKING SURFACES THAT ARE A PART OF AN
<br />ACCESSIBLE ROUTE SHALL COMPLY WITH SECTION 11B-403,
<br />11B-403.5.1 CLEAR WIDTH. EXCEPT AS PROVIDED IN SECTIONS
<br />11B-403.5.2. AND 11B-403.5.3, THE CLEAR WIDTH OF
<br />WALKING SURFACES SHALL BE 36" (914mm).
<br />THE CLEAR WIDTH OF SIDEWALKS AND WALKS SHALL BE 48"
<br />(219mm) MINIMUM. WHEN, BECAUSE OF "RIGHT-AWAY
<br />RESTRICTIONS", NATURAL BARRIERS OR OTHER EXISTING
<br />CONDITIONS, THE ENFORCING AGENCY DETERMINES THAT
<br />COMPLIANCE WITH THE 48-INCH (219mm) CLEAR SIDEWALK
<br />WIDTH WOULD CREATE AN UNREASONABLE HARDSHIP, THE
<br />CLEAR WIDTH MAY BE REDUCED TO 36" (914mm).
<br />11B-303.2 VERTICAL
<br />CHANGES IN THE LEVEL OF 1/4 INCH (6.4mm) HIGH MAXIMUM
<br />SHALL BE PERMITTED TO BE VERTICAL AND WITHOUT EDGE
<br />TREATMENT
<br />11B-303.3 BEVELED.
<br />CHANGES IN LEVEL BETWEEN 1/4 INCH (6.4mm) HIGH MINIMUM
<br />AND 1/2 INCH (12.7mm) HIGH MAXIMUM SHALL BE BEVELED
<br />WITH A SLOPE NOT STEEPER THAN 1:2.
<br />11B-403.3 SLOPE.
<br />THE RUNNING SLOPE OF WALKING SURFACES SHALL NOT BE
<br />STEEPER THAN 1:20. THE CROSS SLOPE OF WALKING
<br />SURFACES SHALL NOT BE STEEPER THAN 1:48.
<br />PROTRUDING OBJECTS
<br />11B-307.2 PROTRUSION LIMITS. OBJECTS WITH LEADING
<br />EDGES MORE THAN 27 INCHES (686 mm) AND NOT MORE THAN
<br />80 INCHES (2032mm) ABOVE THE FINISH FLOOR OR GROUND
<br />SHALL PROTRUDE 4 INCHES (102mm) MAXIMUM HORIZONTALLY
<br />INTO THE CIRCULATION PATH.
<br />FLOOR OR GROUND SURFACES
<br />11B-302.1 GENERAL. FLOOR AND GROUND SURFACES SHALL
<br />BE STABLE, FIRM, AND SLIP RESISTANT AND SHALL COMPLY
<br />WITH SECTION 11B-302.
<br />11B-302.2 CARPET OR CARPET TILE SHALL BE SECURELY
<br />ATTACHED AND SHALL HAVE A FIRM CUSHION, PAD, OR
<br />BACKING OR NO CUSHION OR PAD. CARPET OR CARPET TILE
<br />SHALL HAVE A LEVEL LOOP, TEXTURED LOOP, LEVELCUT PILE,
<br />LEVEL CUT/UNCUT PILE TEXTURE. PILE HEIGHT SHALL BE 1/2 INCH
<br />(12.7MM) MAXIMUM. EXPOSED EDGES OR CARPET SHALL BE
<br />FASTENED TO FLOOR SURFACE AND SHALL HAVE TRIM ON THE
<br />ENTIRE LENGTH OF THE EXPOSED EDGE. CARPET EDGE TRIM
<br />SHALL COMPLY WITH SECTION 11B-303.
<br />11B-302.3 OPENINGS. OPENINGS IN FLOOR OR GROUND
<br />SURFACES SHALL NOT, ALLOW PASSAGE OF A SYPHERE MORE
<br />THAN 1/2 INCH (12.7 MM) DIAMETER EXCEPT AS ALLOWED IN
<br />SECTION 11B-407.4.3
<br />11B-303.2 VERTICAL. CHANGES IN LEVEL GREATER THAN 1/4
<br />INCH (6.4 MM) AND NOT EXCEEDING 1/2 IN HEIGHT SHALL BE
<br />BEVELED WITH A SLOPE NOT STEEPER THEN 1:2 (11B-303) &
<br />(11B-303.3).
<br />SANITARY FACILITIES (GENERAL):
<br />11B-703.7.2.6.3 UNISEX TOILET AND BATHING FACILITIES.
<br />UNISEX TOILET AND BATHING FACILITIES SHALL BE IDENTIFIED BY
<br />A CIRCLE, 1/4 INCH (6.4mm) THICK AND 12 INCHES (305mm) IN
<br />DIAMETER WITH A 1/4 INCH (6.4mm) THICK TRIANGLE WITH A
<br />VERTEX POINTING UPWARD SUPERIMPOSED ON THE CIRCLE AND
<br />WITHIN THE 12-INCH (305mm) DIAMETER. THE TRIANGLE
<br />SYMBOL SHALL CONTRAST WITH THE CIRCLE SYMBOL, EITHER
<br />LIGHT ON A DARK BACKGROUND OR DARK ON A LIGHT
<br />BACKGROUND. THE CIRCLE SYMBOL SHALL CONTRAST WITH THE
<br />DOOR, EITHER LIGHT ON A DARK BACKGROUND OR DARK ON A
<br />LIGHT BACKGROUND.
<br />SANITARY FACILITY FIXTURES & ACCESSORIES:
<br />11B-606.5 EXPOSED PIPES AND SURFACES.
<br />WATER SUPPLY AND DRAIN PIPES UNDER LAVATORIES AND SINKS
<br />SHALL BE INSULATED OR OTHERWISE CONFIGURED TO PROTECT
<br />AGAINST CONTACT. THERE SHALL BE NO SHARP OR ABRASIVE
<br />SURFACES UNDER LAVATORIES AND SINKS.
<br />11B-703.7.2.6 TOILET AND BATHING FACILITIES GEOMETRIC
<br />SYMBOLS. DOORWAYS LEADING TO TOILET ROOMS AND BATHING
<br />ROOMS SHALL BE IDENTIFIED BY A GEOMETRIC SYMBOL
<br />COMPLYING WITH SECTION 11B-703.7.2.6. THE SYMBOL SHALL BE
<br />MOUNTED AT 58 INCHES (1473mm) MINIMUM AND 60 INCHES
<br />(1524mm) MAXIMUM ABOVE THE FINISH FLOOR OR GROUND
<br />SURFACE MEASURED FROM THE CENTERLINE OF THE SYMBOL.
<br />WHERE A DOOR IS PROVIDED THE SYMBOL SHALL BE MOUNTED
<br />WITHIN 1 INCH (25mm) OF THE VERTICAL CENTERLINE OF THE
<br />DOOR.
<br />11B-703.4.1. HEIGHT ABOVE FINISH FLOOR OR GROUND.
<br />TACTILE CHARACTERS ON SIGNS SHALL BE LOCATED 48 INCHES
<br />(1219mm) MINIMUM ABOVE THE FINISH FLOOR OR GROUND
<br />SURFACE, MEASURED FROM THE BASELINE OF THE LOWEST
<br />BRAILLE CELLS AND 60 INCHES (1524mm) MAXIMUM ABOVE THE
<br />FINISH FLOOR OR GROUND SURFACE, MEASURED FROM THE
<br />BASELINE OF THE HIGHEST LINE OF RAISED CHARACTERS.
<br />DOOR, DOORWAYS, AND GATES
<br />1. DOORS, DOORWAYS, AND GATES THAT ARE PART OF AN
<br />ACCESSIBLE ROUTE SHALL COMPLY WITH SECTION (11B-404.1)
<br />2. MANUAL DOORS, DOORWAYS, AND MANUAL GATES INTENDED FOR
<br />USER PASSAGE SHALL COMPLY WITH SECTION 11B-504.2 (PER
<br />11B-404.2)
<br />3. DOOR OPENINGS SHALL PROVIDE A CLEAR WIDTH OF 32" MIN.
<br />CLEAR OPENINGS OF DOORWAYS WITH SWINGING DOORS SHALL BE
<br />MEASURED BETWEEN THE FACE OF THE DOOR AND THE STOP, WITH
<br />THE DOOR OPEN 90 DEGREES. OPENINGS MORE THAN 24" DEEP
<br />SHALL PROVIDE A CLEAR OPENING OF 36" MIN. THERE SHALL BE NO
<br />PROJECTION INTO THE REQUIRED CLEAR OPENING WIDTH LOWER
<br />THAN 34" ABOVE THE FINISH FLOOR OR GROUND. PROJECTIONS
<br />INTO THE CLEAR OPENING WIDTH BETWEEN 34" AND 80" ABOVE
<br />THE FINISH FLOOR OR GROUND SHALL NOT EXCEED 4". (PER
<br />11B-404.2.3)
<br />4. SWINGING DOORS AND GATES SHALL HAVE MANEUVERING
<br />CLEARANCES COMPLYING WITH TABLE 11B-404.2.4.1.
<br />5. RECESSED DOORS & GATES SHALL HAVE MANEUVERING
<br />CLEARANCES FORWARD APPROACH AND SHALL BE PROVIDED WHEN
<br />ANY OBSTRUCTION WITHIN 18" OF THE LATCH SIDE AT AN INTERIOR
<br />DOORWAY, OR WITHIN 24" OF THE LATCH SIDE OF AN EXTERIOR
<br />DOORWAY, PROJECTS MORE THAN 8" BEYOND THE FACE OF THE
<br />DOOR, MEASURED PERPENDICULAR TO THE FACE OF THE DOOR OR
<br />GATE. (PER 11B-404.2.4.3)
<br />6. FLOOR OR GROUND SURFACE WITHIN REQUIRED MANEUVERING
<br />CLEARANCES SHALL COMPLY WITH SECTION 11B-302. CHANGES IN
<br />LEVEL ARE NOT PERMITTED. (PER 11B-404.2.4.4)
<br />7. PROVIDED THRESHOLD AT DOORWAYS SHALL BE 1/2" HIGH MAX.
<br />RAISED THRESHOLDS AND CHANGES IN LEVEL AT DOORWAYS
<br />SHALL COMPLY WITH SECTIONS11B-302 &
<br />11B-303.(PER11B-404.2.5)
<br />8. HANDLES, PULLS, LATCHES, LOCKS, AND OTHER OPERABLE PARTS
<br />ON DOORS AND GATES SHALL COMPLY WITH SECTION 11B-309.4.
<br />OPERABLE PARTS OF SUCH HARDWARE SHALL BE 34" MINI. AND
<br />44" MAX. ABOVE THE FINISH FLOOR OR GROUND. WHERE SLIDING
<br />DOORS ARE IN THE FULLY OPEN POSITION, OPERATING HARDWARE
<br />SHALL BE EXPOSED AND USABLE FROM BOTH SIDES. (PER
<br />11B-404.2.7)
<br />9. DOOR & GATE CLOSING SPEED SHALL COMPLY WITH SECTION
<br />11B-404.2.8.
<br />THE DOOR & GATE CLOSERS SHALL BE ADJUSTED SO THAT FROM
<br />AN OPEN POSITION OF 90 DEGREES, THE TIME REQUIRED TO MOVE
<br />THE DOOR TO A POSITION OF 12 DEGREES FROM THE LARCH IS 5
<br />SECONDS MINIMUM. (PER 11B-404.2.8.1).
<br />DOOR & GATE SPRING HINGES SHALL BE ADJUSTED SO THAT FROM
<br />THE OPEN POSITION OF 70 DEGREES, THE DOOR OR GATE SHALL
<br />MOVE TO THE CLOSED POSITION IN 1.5 SECONDS MIN. (PER
<br />11B-404.2.8.2).
<br />10. THE FORCE FOR PUSHING OR PULLING OPEN A DOOR OR GATE OR
<br />OTHER THAN FIRE DOORS SHALL BE AS FOLLOWS:
<br />A. INTERIOR HINGED DOORS AND GATES: 5 POUNDS MAX.
<br />B. SLIDING OR FOLDING DOORS: 5 POUNDS MAX.
<br />C. REQUIRED FIRE DOORS: THE MINIMUM OPENING FORCE
<br />ALLOWABLE BY THE APPROPRIATE ADMINISTRATIVE AUTHORITY,
<br />NOT TO EXCEED 15 POUNDS.
<br />THE FORCES DO NOT APPLY TO THE FORCE REQUIRED TO RETRACT
<br />LATCH BOLTS OR DISENGAGE OTHER DEVICES THAT HOLD THE
<br />DOOR OR GATE IN A CLOSED POSITION. (PER 11B-404.2.9).
<br />11. SWINGING DOOR AND GATE SURFACES WITHIN 10" OF THE
<br />FINISH FLOOR OR GROUND MEASURED VERTICALLY SHALL HAVE A
<br />SMOOTH SURFACE ON THE PUSH SIDE EXTENDING THE FULL
<br />WIDTH OF THE DOOR OR GATE. PARTS CREATING HORIZONTAL
<br />OR VERTICAL JOINTS IN THESE SURFACES SHALL BE WITHIN 1/16"
<br />OF THE SAME PLANE AS THE OTHER AND BE FREE OF SHARP OR
<br />ABRASIVE EDGES. CAVITIES CREATED BY ADDED KICK PLATES SHALL BE
<br />CAPPED. (PER 11B-404.2.10).
<br />12. AUTOMATIC DOORS & AUTOMATIC GATES SHALL COMPLY WITH
<br />SECTION 11B-404.3. FULL-POWERED AUTOMATIC DOORS SHALL
<br />COMPLY WITH ANSI/BHMA A156.10. LOW-ENERGY AND
<br />POWERASSISTED DOORS SHALL COMPLY WITH ANSI/BHMA
<br />A156.19. (PER 11B-404.3)
<br />13. WHERE DOORS & GATES WITHOUT STANDBY POWER ARE A PART
<br />OF A MEANS OF EGRESS, THE CLEAR BREAK OUT OPENING AT
<br />SWINGING OR SLIDING DOORS AND GATES SHALL BE 32" MIN.
<br />WHEN OPERATED IN EMERGENCY MODE. (PER 11B-404.3.6)
<br />HANDRAILS & GRAB BARS
<br />1. HANDRAIL GRIPPING SURFACES WITH A CIRCULAR CROSS SECTION
<br />SHALL HAVE AN OUTSIDE DIAMETER OF 1 1/4" MIN. AND 2" MAX.
<br />(PER 11B-505.7.1)
<br />HANDRAIL GRIPPING SURFACES AND ANY SURFACES ADJACENT TO
<br />THEM SHALL BE FREE OF SHARP OR ABRASIVE ELEMENTS AND
<br />SHALL HAVE ROUNDED EDGES (PER 11B-505.8)
<br />2. GRAB BARS WITH CIRCULAR CROSS SECTIONS SHALL HAVE AN
<br />OUTSIDE DIAMETER OF 1 1/4" MIN. AND 2" MAX. (PER
<br />11B-606.2.1)
<br />GRAB BARS AND ANY WALL OR OTHER SURFACES ADJACENT TO
<br />GRAB BARS SHALL BE FREE OF SHARP OR ABRASIVE ELEMENTS
<br />AND SHALL HAVE ROUNDED EDGES. (PER 11B-609.5)
<br />COMMUNICATION ELEMENTS
<br />FIRE ALARM SYSTEMS SHALL HAVE PERMANENTLY INSTALLED
<br />AUDIBLE AND VISIBLE ALARMS COMPLYING WITH NFPA 72 &
<br />CHAPTER 9, SECTION 907.5.2.1 AND 907.5.2.3 (PER
<br />11B-702.10)
<br />1. ALL BUILDING ENTRANCES SHALL BE IDENTIFIED WITH SIGNS
<br />THAT COMPLY WITH WITH SECTION 11B-703. WHERE BOTH
<br />VISUAL AND TACTILE CHARACTERS, OR TWO SEPARATE SIGNS,
<br />ONE WITH VISUAL, AND ONE WITH TACTILE CHARACTERS. SHALL
<br />BE PROVIDED. (PER 11B-703.1)
<br />2. SIGNS WITH TACTILE CHARACTERS SHALL COMPLY WITH
<br />SECTION 11B-703.4 & 11B-703.4.1
<br />3. RAISED CHARACTERS SHALL BE 1/32" MIN. ABOVE THEIR
<br />BACKGROUND. 11B-703.2.1
<br />4. CHARACTERS SHALL BE UPPERCASE. 11B-703.2.2
<br />5. CHARACTERS SHALL BE SAN SERIF. CHARACTERS SHALL NOT BE
<br />ITALIC, OBLIQUE, SCRIPT, HIGHLY DECORATIVE, OR OF OTHER
<br />UNUSUAL FORMS. 11B-703.2.3
<br />6. CHARACTERS SHALL BE SELECTED FROM FONTS WHERE THE
<br />WIDTH OF THE UPPERCASE LETTER "O" IN 55 60 PERCENT MIN.
<br />AND 110 PERCENT MAX. OF THE HEIGHT OF THE UPPERCASE
<br />LETTER "I". 11B-703.2.4
<br />7. CHARACTERS HIGH MEASURED VERTICALLY FROM THE BASELINE
<br />OF THE CHARACTER SHALL BE 5/8" MIN. AND 2" MAX. BASED ON
<br />THE HEIGHT OF THE UPPERCASE LETTER "I". 11B-703.2.5.
<br />8. STROKE THICKNESS OF THE UPPERCASE LETTER "I" SHALL BE 15
<br />PERCENT MAX. OF THE HEIGHT OF THE CHARACTER.
<br />11B-703.2.6.
<br />9. CHARACTERS SPACING SHALL BE MEASURED BETWEEN THE TWO
<br />CLOSEST POINTS OF ADJACENT RAISED CHARACTERS WITHIN A
<br />MESSAGE, EXCLUDING WORD SPACES. WHERE CHARACTERS
<br />HAVE RECTANGULAR CROSS SECTIONS, SPACING BETWEEN
<br />INDIVIDUAL RAISED CHARACTERS SHALL BE 1/8" MIN. AND 4
<br />TIMES THE RAISED CHARACTER STROKE WIDTH MAXIMUM.
<br />WHERE CHARACTERS HAVE OTHER CROSS SECTIONS, SPACING
<br />BETWEEN INDIVIDUAL RAISED CHARACTER SHALL BE 1/16" MIN.
<br />AND 4 TIMES THE RAISED CHARACTER STROKE WIDTH MAX. AT
<br />THE TOP OF THE CROSS SECTIONS. CHARACTERS SHALL BE
<br />SEPARATED FROM RAISED BORDERS AND DECORATIVE
<br />ELEMENTS 3/8" MIN. 11B-703.2.7
<br />10. SPACING BETWEEN THE BASELINES OF SEPARATE LINES OF
<br />RAISED CHARACTERS WITHIN A MESSAGE SHALL BE 135% MIN.
<br />AND 170% MAX. OF THE RAISED CHARACTER HEIGHT.
<br />11B-703.2.8
<br />11. TEXT SHALL BE IN A HORIZONTAL FORMAT. 11B-703.2.9
<br />12. BRAILLE SHALL BE CONTRACTED (GRADE 2 ) AND SHALL COMPLY
<br />WITH SECTION 11B-703.3 BRAILLE AND 11B-703.4
<br />INSTALLATION HEIGHT AND LOCATION 11B-703.3
<br />13. BRAILLE DOTS SHALL HAVE A DOMED OR ROUNDED SHAPE AND
<br />SHALL COMPLY WITH TABLE 11B-703.3.1. THE INDICATION OF
<br />AN UPPERCASE LETTER OR LETTERS SHALL ONLY BE USED
<br />BEFORE THE FIRST WORD OF SENTENCES, PROPER NOUNS AND
<br />NAMES, INDIVIDUAL LETTERS OF THE ALPHABET INITIALS, AND
<br />ACRONYMS. 11B-703.3.1
<br />14. BRAILLE SHALL BE POSITIONED BELOW THE CORRESPONDING
<br />TEXT IN A HORIZONTAL FORMAT, FLUSH LEFT OR CENTERED. IF
<br />TEXT IS MULTI-LINED, BRAILLE SHALL BE PLACED BELOW THE
<br />ENTIRE TEXT. BRAILLE SHALL BE SEPARATED 3/8" MIN. AND 1/2"
<br />MAX. FROM ANY OTHER TACTILE CHARACTERS AND 3/8" MIN.
<br />FROM RAISED BORDERS AND DECORATIVE ELEMENTS.
<br />11B-703.3.2 (SEE EXCEPTION).
<br />15. SIGNS WITH TACTILE CHARACTERS SHALL COMPLY WITH
<br />11B-703.4 INSTALLATION HEIGHT AND LOCATION. 11B-703.4
<br />16. TACTILE CHARACTERS ON SIGNS SHALL BE LOCATED 48" MIN.
<br />ABOVE THE FINISH FLOOR OR GROUND SURFACE, MEASURED
<br />FROM THE BASELINE OF THE LOWEST TACTILE CHARACTER
<br />BRAILLE CELLS AND 60" MAX. ABOVE THE FINISH FLOOR OR
<br />GROUND SURFACE, MEASURED FROM THE BASELINE OF THE
<br />HIGHEST TACTILE CHARACTER LINE RAISED CHARACTERS.
<br />11B-703.4.1 (SEE EXCEPTION)
<br />17. WHERE A TACTILE SIGN IS PROVIDED AT DOOR, THE SIGN SHALL
<br />BE LOCATED ALONGSIDE THE DOOR AT THE LATCH SIDE. WHERE
<br />A TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH ONE
<br />ACTIVE LEAF, THE SIGN SHALL BE LOCATED ON THE INACTIVE
<br />LEAF. WHERE A TACTILE SIGN IS PROVIDED AT DOUBLE DOORS
<br />WITH TWO ACTIVE LEAFS, THE SIGN SHALL BE LOCATED TO THE
<br />RIGHT OF THE RIGHT HAND DOOR. WHERE THERE IS NO WALL
<br />SPACE AT THE LATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT
<br />SIDE OF DOUBLE DOORS, SIGNS SHALL BE LOCATED ON THE
<br />NEAREST ADJACENT WALL. SIGNS CONTAINING TACTILE
<br />CHARACTERS SHALL BE LOCATED SO THAT A CLEAR FLOOR
<br />SPACE OF 18" MIN. BY 18" MIN, CENTERED ON THE TACTILE
<br />CHARACTERS, IS PROVIDED BEYOND THE ARC OF ANY DOOR
<br />SWING BETWEEN THE CLOSED POSITION AND 45 DEGREE OPEN
<br />POSITION. WHERE PERMANENT IDENTIFICATION SIGNAGE IS
<br />PROVIDED FOR ROOMS AND SPACES THEY SHALL BE LOCATED
<br />ON THE APPROACH SIDE OF THE DOOR AS ONE ENTERS THE
<br />ROOM OR SPACE. SIGNS THAT IDENTIFY EXITS SHALL BE
<br />LOCATED ON THE APPROACH SIDE OF THE DOOR AS ONE
<br />ENTERS THE ROOM OR SPACE. SIGNS THAT IDENTIFY EXITS
<br />SHALL BE LOCATED ON THE APPROACH SIDE OF THE DOOR AS
<br />ONE EXITS THE ROOM OR SPACE. 11B-703.4.2 (SEE
<br />EXCEPTION)
<br />18. VISUAL CHARACTERS SHALL COMPLY WITH THE FOLLOWING,
<br />EXCEPT WHERE VISUAL CHARACTERS COMPLY WITH 11B-703.2
<br />RAISED CHARACTERS AND ARE ACCOMPANIED BY BRAILLE
<br />COMPLYING WITH 11B-703.3 BRAILLE, THEY SHALL NOT BE
<br />REQUIRED TO COMPLY WITH 11B-703.5.2 THROUGH
<br />11B-703.5.6,11B-703.5.8 AND 11B-703.5.9
<br />ELECTRICAL:
<br />(11B-308.1.1) ELECTRICAL SWITCHES. CONTROLS AND SWITCHES
<br />INTENDED TO BE USED BY THE OCCUPANT OF A ROOM OR AREAS
<br />TO CONTROL LIGHTING AND RECEPTACLE OUTLETS, APPLIANCES OR
<br />COOLING, HEATING AND VENTILATING EQUIPMENT, SHALL COMPLY
<br />WITH SECTION 11B-308 EXCEPT THE LOW REACH SHALL BE
<br />MEASURED TO THE BOTTOM OF THE OUTLET BOX AND THE HIGH
<br />REACH SHALL BE MEASURED TO THE TOP OF THE OUTLET BOX.
<br />(11B-308.1.2) ELECTRICAL RECEPTACLE OUTLETS. ELECTRICAL
<br />RECEPTACLE OUTLETS ON BRANCH CIRCUITS OF 30 AMPERES OR
<br />LESS AND COMMUNICATION SYSTEM RECEPTACLES SHALL COMPLY
<br />WITH SECTION 11B-308 EXCEPT THE LOW REACH SHALL BE
<br />MEASURED TO THE BOTTOM OF THE OUTLET BOX AND THE HIGH
<br />REACH SHALL BE MEASURED TO THE TOP OF THE OUTLET BOX.
<br />OPERABLE PARTS:
<br />(11B-309.4) OPERATION. OPERABLE PARTS SHALL BE OPERABLE
<br />WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING,
<br />PINCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO
<br />ACTIVATE OPERABLE PARTS SHALL BE 5 POUNDS MAXIMUM.
<br />JOB#
<br />DATE
<br />DRAWN
<br />SCALE
<br />Th
<br />i
<br />s
<br />
<br />D
<br />u
<br />c
<br />o
<br />u
<br />m
<br />e
<br />n
<br />t
<br />
<br />i
<br />s
<br />
<br />t
<br />h
<br />e
<br />
<br />p
<br />r
<br />o
<br />p
<br />e
<br />r
<br />t
<br />y
<br />
<br />o
<br />f
<br />
<br />Y
<br />N
<br />
<br />A
<br />R
<br />C
<br />H
<br />I
<br />T
<br />E
<br />C
<br />T
<br />S
<br />,
<br />
<br />I
<br />N
<br />C.
<br />,
<br />
<br />a
<br />n
<br />d
<br />
<br />s
<br />h
<br />a
<br />l
<br />l
<br />
<br />n
<br />o
<br />t
<br />
<br />be
<br />
<br />r
<br />e
<br />p
<br />o
<br />r
<br />d
<br />u
<br />c
<br />e
<br />d
<br />
<br />w
<br />i
<br />t
<br />h
<br />o
<br />u
<br />t
<br />
<br />t
<br />h
<br />e
<br />
<br />w
<br />r
<br />i
<br />t
<br />t
<br />e
<br />n
<br />
<br />c
<br />o
<br />n
<br />s
<br />e
<br />n
<br />t
<br />
<br />o
<br />f
<br />
<br />Y
<br />N
<br />G
<br />
<br />A
<br />R
<br />CH
<br />I
<br />T
<br />E
<br />C
<br />T
<br />S
<br />,
<br />
<br />I
<br />N
<br />C
<br />.
<br />©
<br />C
<br />O
<br />P
<br />Y
<br />R
<br />I
<br />G
<br />H
<br />T
<br />RE
<br />V
<br />I
<br />S
<br />I
<br />O
<br />N
<br />S
<br />No. C-32798
<br />HC
<br />F
<br />RADSEN
<br />E
<br />S
<br />TAT
<br />LCAIOF
<br />E
<br />ILC
<br />A
<br />ORNI
<br />TC
<br />ITEYENNY NG
<br />DATE
<br />RENEWAL
<br />03-31-25
<br />1/4" = 1'-0"
<br />A0.2
<br />AC
<br />C
<br />E
<br />S
<br />S
<br />I
<br />B
<br />I
<br />L
<br />I
<br />T
<br />Y
<br />
<br />N
<br />O
<br />T
<br />E
<br />S
<br />YC23005
<br />AN
<br />C
<br />E
<br />N
<br />A
<br />Y
<br />
<br />C
<br />O
<br />M
<br />M
<br />E
<br />R
<br />C
<br />I
<br />A
<br />L
<br />
<br />O
<br />F
<br />F
<br />I
<br />C
<br />E
<br />JAN 2024
<br />T.N.
<br />21
<br />0
<br />
<br />W
<br />.
<br />
<br />1
<br />9
<br />T
<br />H
<br />
<br />S
<br />T
<br />R
<br />E
<br />E
<br />T
<br />,
<br />SA
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />6
<br />Da
<br />t
<br />e
<br />
<br />D
<br />e
<br />s
<br />c
<br />r
<br />i
<br />p
<br />t
<br />i
<br />o
<br />n
<br />ACCESSIBILITY NOTES
<br />2DOORS4PRIVACY/UNISEX TOILET ROOM7SIGNS/PICTOGRAMS
<br />1DOOR CLEAR SPACE3REACH REQUIREMENTS5THREDSHOLDS/LEVEL CHANGE
<br />6PROTRUDING OBJECTS
<br />210 W 19th St
<br />4/14/2025
|