2112 S Woodland Pl - Plan - Laserfiche WebLink

Home Browse Search

SITE NOTES: A LADDER WILL BE IN PLACE FOR INSPECTION IN COMPLIANCE WITH OSHA REGULATION. THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE AND THIS SYSTEM IS A UTILITY INTERACTIVE SYSTEM WHIT NO STORAGE BATTERIES. THE SOLAR PV INSTALLATION WILL NOT OBSTRUCT ANY PLUMBING, MECHANICAL, OR BUILDING ROOF VENTS. PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT WILL BE PROVIDED AS PER SECTION CEC 110.26 ROOF COVERINGS SHALL BE DESIGNED, INSTALLED, AND MAINTAINED IN ACCORDANCE WITH THIS CODE AND APPROVED MANUFACTURERS INSTRUCTIONS SUCH THAT THE ROOF COVERING SERVES TO PROTECT THE BUILDING OR STRUCTURE. EQUIPMENT LOCATIONS: ALL EQUIPMENT SHALL MEET MINIMUM SETBAKC AS REQUIRED BY CEC 110.26. WIRING SYSTEMS INSTALLED IN DIRECT SUNLIGHT MUST BE RATED FOR EXPECTED OPERATING TEMERATURES AS SPECIFIED BY CEC 690.31 (A),(C) AND CEC TABLES 310.15 (B)(2)(C). JUNCTION AND PULL BOXES PERMITTED INSTALLED UNDER PV MODULES ACCORDING TO CEC 690.34 ADDITIONAL AC DISCONNECT(S) SHALL BE PROVIDED WHERE THE INVERTER IS NOT WITHIN SIGHT OF THE AC SERVICING DISCONNECT. ALL EQUIPMENT SHALL BE INSTALLED ACCESSIBLE TO QUALIFIED PERSONNEL ACCORDING TO CEC APPLICABLE CODES. ALL COMPONENTS ARE LISTED FOR THEIR PURPOSE AND RATED FOR OUTDOOR USAGE WHEN APPROPRIATE. STRUCTURAL NOTES: RACKING SYSTEM AND PV ARRAY WILL BE INSTALLED ACCORDING TO CODE-COMPLIANT INSTALLATION MANUAL. TOP CLAMPS REQUIRE A DESIGNATED SPACE BETWEEN MODULES, AND RAILS MUST BE ALSO EXTEND A MINIMUM DISTANCE BEYOND EITHER EDGE OF THE ARRAY/SUBARRAY, ACCORDING TO RAIL MANUFACTURERS INSTRUCTIONS. JUNCTION BOX WILL BE INSTALLED PER MANUFACTURERS SPECIFICATIONS. IF ROOF-PENETRATING TYPE, IT SHALL BE FLASHED AND SEALED PER LOCAL REQUIREMENTS. ROOFTOP PENETRATIONS FOR PV RACEWAY WILL BE COMPLETED AND SEALED WITH APPROVED CHEMICAL SEALANT PER CODE BY A LICENSED CONTRACTOR. ALL PV RELATED ROOF ATTACHMENTS TO BE SPACED NO GREATER THAN THE SPAN DISTANCE SPECIFIED BY THE RACKING MANUFACTURER. WHEN POSSIBLE, ALL PV RELATED RACKING ATTACHMENTS WILL BE STAGGERED AMONGST THE ROOF FRAMING MEMBERS. EQUIPMENT LOCATIONS: ALL EQUIPMENT SHALL MEET MINIMUM SETBAKC AS REQUIRED BY CEC 110.26. WIRING SYSTEMS INSTALLED IN DIRECT SUNLIGHT MUST BE RATED FOR EXPECTED OPERATING TEMERATURES AS SPECIFIED BY CEC 690.31 (A),(C) AND CEC TABLES 310.15 (B)(2)(C). JUNCTION AND PULL BOXES PERMITTED INSTALLED UNDER PV MODULES ACCORDING TO CEC 690.34 ADDITIONAL AC DISCONNECT(S) SHALL BE PROVIDED WHERE THE INVERTER IS NOT WITHIN SIGHT OF THE AC SERVICING DISCONNECT. ALL EQUIPMENT SHALL BE INSTALLED ACCESSIBLE TO QUALIFIED PERSONNEL ACCORDING TO CEC APPLICABLE CODES. ALL COMPONENTS ARE LISTED FOR THEIR PURPOSE AND RATED FOR OUTDOOR USAGE WHEN APPROPRIATE. WIRING AND CONDUIT NOTES: ALL CONDUIT AND WIRE WILL BE LISTED AND APPROVED FOR THEIR PURPOSE. CONDUIT AND WIRE SPECIFICATIONS ARE BASED ON MINIMUM CODE REQUIREMENTS AND ARE NOT MEANT TO LIMIT UP-SIZING. CONDUCTOR SIZED ACCORDING TO CEC 690.8, CEC 690.7. VOLTAGE DROP LIMITED TO 1.5% DC WIREING LIMITED TO MODULE FOOTPRINT. MICROINVERTER WIREING SYSTEMS SHALL BE LOCATED AND SECURED UNDER THE ARRAY WITH SUITABLE WIREING CLIPS. AC CONDUCTORS COLORED OR MARKED AS FOLLOWS: PHASE A OR L1- BLACK PAHSE B OR L2- RED, OR OTHER CONVENTION IF THREE PHASE PHASE C OR L3- BLUE, YELLOR, ORANGE**, OR OTHER CONVENTION NEUTRAL- WHITE OR GRAY IN 4-WIRE DELTA CONNECTED SYSTEMS THE PHASE WITH HIGHER VOLTAGE TO BE MARKED ORANGE [CEC 110.15]. grounding notes: grounding system components shall be listed for their purpose, and grounding devices exposed to the elements shall be rated for such use. pv equipment shall be grounded according to cec 690.43 and minimum cec table 250.122 mental parts of modules frames, modules racking, and enclosures considered groined in accord with 250.134 and 250.136(a). equipment grounding conductors shall be sized according to cec 690.45 and micoinverters manufacturers instructions. each modules will be grounded using weeb grounding clips as shown in manufacturer documentation and approved by the ahj. if weebs are not used, module grounding lugs must be installed at the specified grounding lugs holes per the manufacturers installation requirements. the grounding connection to a module shall be arranged such that the removal of a module does not interrupt a grounding conductor to another module. grounding and bonding conductors, if insulated, shall be colored green or marked green if #4 awg or larger [cec 250.119]. the grounding electrode system complies with cec 690.47 and cec 250.50 through 250.106. if existing system is inaccessible, or inadequate, a grounding electrode system provided according to cec 250, cec 690.47 and ahj. grounding-fault detection shall comply with cec 690.41(b)(1) and (2) to reduce fire hazards. disconnection and over-current protection notes: disconnecting switches shall be wired such that when the switch is opened the conductors remaining energized are connected to the terminals marked "lineside" (typically the upper terminals). disconnects to be accessible to qualified utility personnel, be lockable, and be a visible-break switch. pv system circuits installed on or in buildings shall include a rapid shutdown function to reduce shock hazard for emergency responders in accordance with 690.12(a) through (d). all ocpd ratings and types specified according to cec 690.8, 690.9, and 240. microinverter branches connected to a single breaker or grouped fuses in accordance with cec 110.3(b). if required by ahj, system will included arc-fault circuit protection according to cec 690.11 and ul 1699b. interconnection notes: load-side interconnection shall be in accordance with [cec 705.12(b)] the sum of the utility ocpd and inverter continuous output may not exceed 120% of busbar rating [cec 705.12(d)(2)(3)]. the sum of 125 percent of the power source(s) output circuit current and the rating of the over current device protecting the busbar shall not exceed 120 percent of the ampacity of the busbar, pv dedicated back feed breakers must be located opposite end of the bus from the utility source ocpd [cec 705.12(b)(2)(3)]. at multiple electric power sources output combiner panel, total rating of all over current devices shall not exceed ampacity of busbar, however, the combined over current device may be excluded according to cec 705.12(b)(2)(3)(c). feeder tap interconnection (load side) according to cec 705.12 (b)(2)(1). supply side tap interconnection according to cec 705.12 (a) with service entrance conductors in accordance with cec 230.42 backfeeding breaker for electric power sources output is exempt from additional fastening [cec 705.12(b)(5). PLANSET-2 SITE INFORMATION drawn by: sheet name: REVISION: sheet number: site notes PS-2 CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC CEC AHJ:SANTA ANA CITY BUILDING CODE:2022 CBC ELECTRICAL CODE:2022 CEC FIRE CODE:2022 CBC RESIDENTIAL CODE:2022 CRC ELISABETH LE GUIN 2212 SOUTH WOODLAND PLACE SANTA ANA CALIFORNIA 92707 EE 1099198 CONTRACTOR LICENSE NUMBER CONFIDENTIAL - THE INFORMATION HEREIN CONTAINED SHALL NOT BE USED FOR THE BENEFIT OF ANYONE EXCEPT SOLID STATE ELECTRIC LLC, NOR SHALL IT BE DISCLOSED IN WHOLE OR IN PART TO OTHERS OUTSIDE RECIPIENT ORGANIZATIONS, EXCEPT IN CONNECTION WITH THE SALE AND USE OF THE RESPECTIVE EQUIPMENT, WITHOUT THE WRITTEN PERMISSION OF SOLID STATE ELECTRIC LLC. FLEX ENERGY ELECTRIC LLC 472 E 1750 N SUIT 200, VINEYARD, UT 84059 04/25/2023 3 2112 S Woodland Pl06/20/23