Laserfiche WebLink
THE COMPLETE ROOF ATTACHMENT SOLUTION <br />FEATURING TECHNOLOGY <br />FLASHKIT PRO is the complete attachment solution for composition shingle roofs. Unirac partnered with EcoFasten <br />Solar to bring best-in-class design and performance together in one package. Kitted in 10 packs for maximum <br />convenience, flashings and hardware are available in Mill or Dark finishes. With FLASHKIT PRO, you have everything <br />you need for a quick, professional installation. <br />YOUR COMPLETE SOLUTION <br />Flashings, lags, continuous slot L-Feet and hardware <br />CONVENIENT 10 PACKS <br />Packaged for speed and ease of handling <br />FEATURING TECHNOLOGY <br />FLASHKIT PRO <br />25 <br />YEAR <br />FULL-SYSTEM <br />WARRANTY <br />TRUSTED WATER SEAL FLASHINGS <br />FEATURING TECHNOLOGY <br />FOR QUESTIONS OR CUSTOMER SERVICE VISIT UNIRAC.COM OR CALL (505) 248-2702 <br />FASTER INSTALLATION. 25-YEAR WARRANTY. <br />FLASH KIT PRO IS THE COMPLETE FLASHING AND ATTACHMENT SOLUTION FOR COMPOSITION ROOFS. <br />FOR QUESTIONS OR CUSTOMER SERVICE VISIT UNIRAC.COM OR CALL (505) 248-2702 <br />PRE-INSTALL SYSTEM LAYOUT <br />• Locate rafters and snap horizontal and vertical lines to mark the <br />installation position for each flashing. <br />• Drill a pilot hole (1/4" diameter) for the lag bolt. Backfill with sealant. <br />STEP 1 INSTALL FLASHKIT PRO FLASHING <br />• Insert the flashing so the top part is under the next row of shingles <br />and pushed far enough upslope to prevent water infiltration through <br />vertical joint in shingles. <br />• The leading edge of flashing must butt against upper row of nails to <br />prevent turning when torqued. <br />QUICK TIP: <br />• For vertical adjustment when leading edge of flashing hits nails in <br />upper shingle courses, slide flashing up under shingles until leading <br />edge engages nails. Measure remaining distance to adjust upslope. <br />• Remove flashing and cut a "V" notch at marks where nail shafts <br />engaged leading edge of flashing the distance desired in Step 1. <br />Notch depth not to exceed 2" in length by 1/2" in width. <br />• Re-install flashing with notched area upslope, and position notched <br />leading edge underneath nail heads. <br />STEP 2 INSTALL L-FOOT <br />• Line up pilot hole with FLASHKIT PRO fastener hole. <br />• Insert the lag bolt through the EPDM washer, the top L-101-3 <br />compression bracket, and the gasketed hole in the flashing and into <br />the rafter. <br />• Torque to 100-140 torque inch-pounds depending on the type of <br />wood and time of year. The visual indicator for proper torque is when <br />the EPDM on the underside of the bonded washer begins to push out <br />the sides as the washer compresses. If using an impact wrench to <br />install the fasteners be careful not to over torque the fastener. You <br />may need to stop and use a ratchet to finish the install. <br />STEP 3 ATTACH L-FOOT TO RAIL <br />• Slide the 3/8"-16 racking hardware into rail slot, spacing bolts to <br />match the spacing of the attachments. <br />• Torque 3/8" nut to 30ft-lbs. Use anti-seize to prevent galling. <br />• If attaching L-Foot to light rail, ensure the L-Foot does not <br />protrude above the top edge of the rail. <br />INSTALL FLASHKIT PRO FLASHING <br />STEP 1 STEP 2 STEP 3 <br />INSTALL L-FOOT ATTACH L-FOOT TO RAIL <br />FEATURING TECHNOLOGY <br />FLASHKIT PRO <br />INSTALLATION GUIDE <br />2332 N Spurgeon <br />St05/30/23