5127 W Edinger Ave #G - Plan - Laserfiche WebLink

Home Browse Search

WH WAITING BARBER AREA HALLWAY VIP 1 VIP 2 BREAK ROOM STORAGE (E) RESTROOM LIGHTING FIXTURE SCHEDULE SYMBOL ID DESCRIPTION LOCATION LAMP TYPE WATTAGE MANUFACTURER // MODEL MOUNTING HEIGHT NOTES F1 RECESSED DOWNLIGHT CEILING LED TBD TO MATCH WITH EXISTING LIGHT V.I.F. F2 BUG EYES WALL LED 5 LOTHONIA / 2-LIGHT LED EMERGENCY V.I.F. 90-MIN EMERGENCY BATTERY BACKUP NOTES: 1. CONFIRM LIGHT FIXTURES WITH OWNER/ARCHITECT PRIOR TO BID. 2. COORDINATE ALL LOCATIONS WITH ARCHITECT. 3. FOR CEILING AREAS WITH INSULATION WHERE RECESSED LIGHT CANS ARE SHOWN, PROVIDE AT-RATED FIXTURES ONLY AND INSULATION CONTACT WITH IC-RATING. 4. PERMANETLY INSTALLED LUMINAIRES IN RESIDENTIAL KITCHENS, BATHROOM, GARAGES, LAUNDRY ROOMS, AND UTILITY ROOMS SHALL BE HIGH EFFICACY LUMINAIRES. (130(b), 150(k)) 5. ALL OTHER RESIDENTIAL LUMINAIRES SHALL BE HIGH EFFICACY TYPE UNLESS CONTROLLED BY CERTIFIED DIMMERS OR OCCUPANCY SENSORS. (150(k)4) 6. OUTDOOR LUMINAIRES SHALL BE HIGH EFFICACY TYPE UNLESS CONTROLLED BY CERTIFIED OCCUPANCY SENSORS WITH INTEGRAL PHOTOCONTROL. (150(k)) GENERAL NOTES EXISTING LIGHTING PLAN 1/4" = 1'-0 1.REFER TO ARCHITECTURAL PLANS FOR EXACT LOCATION AND ELEVATION OF ALL LIGHTING FIXTURES AND ALL DEVICES. ALL WALL MOUNTED DEVICE SHALL BE VERIFIED WITH THE ARCHITECT PRIOR TO ROUGH-IN. 2.VERIFY EXACT CEILING CONSTRUCTION WITH ARCHITECTURAL REFLECTED CEILING PLAN AND PROVIDE LIGHTING FIXTURES WITH ALL NECESSARY MOUNTING HARDWARE. 3.ALL RECESSED FIXTURES SHALL BE PROVIDED WITH ALL REQUIRED STRUCTURAL SUPPORTS AS REQUIRED BY THE CURRENTLY ADOPTED ISSUE OF THE UNIFORM BUILDING CODE, AS WELL AS ANY LOCAL CODES. 4.ALL COVE MOUNTED FIXTURES SHALL EXTEND THE FULL LENGTH OF THE COVE. 5.ALL DIMMING BRANCH CIRCUITS SHALL BE PROVIDED WITH A DEDICATED NEUTRAL CONDUCTOR FOR EACH ZONE/CHANNEL. 6.REFER TO ARCHITECTURAL PLANS FOR EXIT SIGN AND NUMBER OF FACTS PER EXIT SIGN. 7.WHEN EXPOSED CEILINGS OR OPEN GRID CONDITIONS OCCUR, THE CONTRACTOR WILL NEED TO PROVIDE THE FOLLOWING ITEMS: - ALL BRANCH CIRCUITS SHALL BE IN EMT. - ALL BRANCH CIRCUITS SHALL BE ROUTED NEATLY AND IN PARALLEL TO STRUCTURES OR DUCT WORK. THE TERM "TRAINED" MEANS ALL PARALLEL CONDUITS SHALL MAINTAIN THE SAME SPATIAL RELATIONSHIP WITH EACH OTHER FOR ENTIRE RUN TO INCLUDE RADIUS BENDS AND SWEEPS. 8.CONTRACTOR TO INCLUDE AN ALLOWANCE TO CORE AND SEAL PENETRATIONS THROUGH STRUCTURAL CONCRETE WALLS. COORDINATE LOCATIONS AND REQUIREMENTS WITH ARCHITECTURAL AND STRUCTURAL DRAWING. 9.COORDINATE ALL PENETRATIONS WITH STRUCTURAL PLANS AND DETAILS. NO PENETRATIONS ARE PERMITTED UNLESS SPECIFICALLY NOTED ON STRUCTURAL DRAWINGS. 10.EMERGENCY/EGRESS FIXTURES SHALL BE CONNECTED TO LOCAL CIRCUIT SERVING RESPECTIVE AREA AND AHEAD OF ALL CONTROLS. 11.ALL LIGHT FIXTURES ARE SHOWN WITH "EM" SHOULD BE EQUIPPED WITH UL924 LISTED 90 MINUTES EMERGENCY BATTERY BACKUP. PROVIDE ADDITIONAL UN-SWITCHED HOT CONDUCTOR TO BATTERY BACKUP. WHEN NORMAL SWITCH IS LOST, "EM" FIXTURE SHALL TURN "ON" FOR A MINIMUM OF 90 MINUTES. 12.EXIT SIGN ARE UN-SWITCHED. PROVIDE INTEGRATED BATTERY BACKUP WITH TEST SWITCH FOR ALL EXIT SIGNS KEYED NOTES EXIT SIGN ARE UN-SWITCHED. PROVIDE INTEGRATED BATTERY BACKUP WITH TEST SWITCH FOR ALL EXIT SIGNS. KEEP THE EXISTING SIGNAGE AND THE CIRCUIT. INSTALL ALL NEW LIGHTING SWITCHES AND SENSORS, AND REVISE THE WIRING FOR THE CONTROLS. 1 2 EXIT 1 NEW LIGHTING PLAN 1/4" = 1'-0 ·ALL REMOVED MATERIALS AND EQUIPMENT WHICH IN THE OPINION OF THE OWNER/ARCHITECT ARE SALVAGEABLE, SHALL REMAIN THE PROPERTY OF THE OWNER. DELIVER SUCH SALVAGED ·MATERIALS AND EQUIPMENT ON PREMISES AS DIRECTED, NEATLY PILE OR STORE THEM AND PROTECT FROM DAMAGE. DO NOT REUSE MATERIALS AND EQUIPMENT UNLESS SPECIFICALLY ·INDICATED ON PLANS OR SPECIFIED. REMOVE FROM PREMISES AND DISPOSE OF ALL MATERIALS CONSIDERED BY THE OWNER/ARCHITECT TO BE SCRAP. ·DISCONNECT AND REMOVE EXISTING ELECTRICAL EQUIPMENT, DISCONNECT SWITCHES, RECEPTACLES, MOUNTING HARDWARE AND ASSOCIATED RACEWAYS, CONDUCTORS AND OUTLET BOXES. ·WHERE OUTLET BOXES ARE FLUSH AND CONDUITS ARE CONCEALED IN EXISTING REMAINING WALLS, REMOVE WIRING AND ABANDON CONDUIT IN PLACE. ·COVER UNUSED AND/OR ABANDONED OUTLETS WITH BLANK COVER PLATES. ·DISCONNECT ABANDONED CIRCUITS AT EXISTING PANELBOARDS AND REMOVE WIRE TO LAST REMAINING DEVICE, LABEL ALL ABANDONED CIRCUIT BREAKERS "SPARE". ·PROVIDE NEW TYPEWRITTEN DIRECTORIES FOR RE-USED PANELBOARDS THAT ARE ALTERED AS PART OF THE DEMOLITION ·ELECTRICAL CONTRACTOR TO VISIT FIELD AND REMOVE EXISTING WIRES AND/OR RECEPTACLES THAT ARE NOT USED. ·EXISTING RECEPTACLES SHOULD BE RELOCATED TO THE NEW LOCATION AS PER NEW PLANS. ·ELECTRICAL CONTRACTOR TO VISIT FIELD AND VERIFY IF EXISTING CONDUITS CAN BE USED. DEMOLITION NOTES : 1.THE EXISTING RECEPTACLE SHOULD BE RELOCATED TO THE NEW LOCATION AS PER THE NEW PLANS. 2.REMOVE THE EXISTING WIRES. 3.THE EXISTING CONDUITS CAN BE USED. GENERAL DEMOLISH NOTES (E)EXISTING (ER)EXISTING TO BE REMOVED (N)NEW LEGEND : (E) (E) (E) (E) (E) (E)(E) (E) (E) (E) (E)(E) (E)(E) (E) (E)(E) (E) (E) (E) (E)(E) (E)(E) (N) F1 (N) F2 (N) F2 (N) F2 (N) F2 (N) F2 (N) F2 (N) F2 (N) F2(N) F2 a 3a A-3 OS OS OS OS OSS ©2024Sheet No. Revisions 1 24303Project No. Date Hu n t i n g t o n E x e c u t i v e P a r k P h o n e : ( 7 1 4 ) 9 2 8 - 2 0 0 6 16 1 6 8 B e a c h B l v d , S t e # 2 0 1 C W e b s i t e : H o m e T o p H o m e . c o m Hu n t i n g t o n B e a c h , C A 9 2 6 4 7 E m a i l : i n f o @ H o m e T o p H o m e . c o m Pr o j e c t f o r : BA R B E R S H O P 51 2 7 W E D I N G E R A V E N U E , S U I T E G SA N T A A N A , C A 9 2 7 0 4 November 23, 2024 Design by TRINH HA, M. Arch. E-1.1 LIGHTING PLAN Design by TRINH HA, M. Arch.TUNG VO, M.S., P.E. C 69546 Exp: 06/30/26 TUNG T HANH VO C I V I LSTATE OF CALIFORNIA REGISTERED PROFESSIONAL ENGINEER 5127 W Edinger Ave #G5/8/2025