HOLD - 122 N Bewley St - Plan - Laserfiche WebLink

Home Browse Search

ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this report, or as to any product covered by the report. Copyright © 2022 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 8 www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ® ICC-ES Evaluation Report Reissued January 2022 ESR-2762 This report is subject to renewal January 2023. DIVISION: 06 00 00—WOOD, PLASTICS AND COMPOSITES Section: 06 17 53—Shop-Fabricated Wood Trusses REPORT HOLDER: SIMPSON STRONG-TIE COMPANY INC. EVALUATION SUBJECT: SIMPSON STRONG-TIE® METAL CONNECTOR PLATES AND HINGE PLATE CONNECTORS FOR WOOD TRUSSES 1.0 EVALUATION SCOPE Compliance with the following codes: 2021, 2018, 2015, 2012, and 2009 International Building Code® (IBC) 2021, 2018, 2015, 2012, and 2009 International Residential Code® (IRC) For evaluation for compliance with codes adopted by the Los Angeles Department of Building and Safety (LADBS), see ESR-2762 LABC and LARC Supplement. Property evaluated: Structural 2.0 USES Simpson Strong-Tie® metal connector plates (AS 20, AS 20HS, AS 18, AS 18S, AS 18S6 and AS 18S5) are used as joint connectors for metal-plate-connected wood roof and floor trusses. Simpson Strong-Tie® hinge plate connectors (ASHP) are used as joint connectors for end- to-end sheathed truss chord members in prefabricated wood trusses complying with IBC Section 2303.4 and IRC Sections R502.11 and R802.10. 3.0 DESCRIPTION 3.1 AS 20: Simpson Strong-Tie AS 20 metal connector plates are staggered-tooth metal plates manufactured from minimum No. 20 gage [0.0356 inch (0.904 mm) total thickness] steel complying with ASTM A653, SS Grade 40 with a minimum G60 galvanization coating [0.0005 inch on each side (0.013 mm)] and having a base-metal thickness of 0.0346 inch (0.879 mm). Each plate has eight teeth per square inch, and each tooth is 0.375 inch (9.5 mm) long. The teeth are punched in pairs and formed at right angles to the face of the parent metal so that two teeth per hole occur along the length. The spacing along the longitudinal direction of each punched slot is 1 inch (25.4 mm) on center, and the pairs are spaced 0.25 inch (6.35 mm) on center along the width of the plate. Alternating rows of teeth are staggered 0.125 inch (3.18 mm) from adjacent rows. See Figure 1. 3.2 AS 20HS: Simpson Strong-Tie AS 20HS metal connector plates are staggered-tooth metal plates manufactured from minimum No. 20 gage [0.0345 inch (0.876 mm) total thickness] steel complying with ASTM A653, HSLAS Grade 60 with a minimum G60 galvanization coating [0.0005 inch (0.013 mm)] and having a minimum base- metal thickness of 0.0335 inch (0.851 mm). Each plate has six teeth per square inch, and each tooth is 0.375 inch (9.5 mm) long. The teeth are punched in pairs and formed at right angles to the face of the parent metal so that two teeth per hole occur along the length. The spacing along the longitudinal direction of each punched slot is 1 inch (25.4 mm) on center, and the pairs are spaced 0.25 inch (6.35 mm) on center and grouped in sets of three with every fourth row removed along the width of the plate. Alternating rows of teeth are staggered 0.125 inch (3.18 mm) from adjacent rows. See Figure 5. 3.3 AS 18: Simpson Strong-Tie AS 18 metal connector plates are staggered-tooth metal plates manufactured from minimum No. 18 gage [0.0466 inch (1.184 mm) total thickness] steel complying with ASTM A653, HSLAS Grade 60 with a minimum G60 galvanization coating [0.0005 inch on each side (0.013 mm)] and having a base-metal thickness of 0.0456 inch (1.158 mm). Each plate has eight teeth per square inch, and each tooth is 0.375 inch (9.5 mm) long. The teeth are punched in pairs and formed at right angles to the face of the parent metal so that two teeth per hole occur along the length. The spacing along the longitudinal direction of each punched slot is 1 inch (25.4 mm) on center, and the pairs are spaced 0.25 inch (6.35 mm) on center along the width of the plate. Alternating rows of teeth are staggered 0.125 inch (3.18 mm) from adjacent rows. See Figure 2. 3.4 AS 18S: Simpson Strong-Tie AS 18S metal connector plates are staggered-tooth metal plates manufactured from HOLD - 122 N Bewley St9/24/2024