3201 S Halladay St - Plan - Laserfiche WebLink

Home Browse Search

C B C A C C E S S I B I L I T Y N O T E S & D E T A I L S CBC-2 SHEET NUMBER S H E E T T I T L E S I T E L O C A T I O N B U S I N E S S O W N E R : D E S I G N E R 5ASECTION 11B-501 - ACCESSIBLE PARKING: 11B-502.1 - GENERAL Car and van parking spaces shall comply with Section 11B-502. Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings. Exception: Where parking spaces or access aisles are not adjacent to another parking space or access aisle, measurements shall be permitted to include the full widthof the line deﬁning the parking space or access aisle. *NOTE: In parking facilities that do not serve a particular building, accessible parking shall be located on the short-est possible route of travel to an accessible pedestrian entrance of the parking facility. In buildings with multiple accessible entrances with adjacent parking, accessible parking spaces shall be dispersed and located closest to the accessible entrances. Table 11-208.2 establishes the number of spaces required. 11B-502.2. Vehicle Space(s) Car and van parking spaces shall be 216 inches (5486 mm) long minimum. Car parking spaces shall be 108 inches (2743 mm) wide minimum and van parking spaces shall be 144 inches (3658 mm) wide minimum, shall be marked to deﬁne the width, and shall have an adjacent access aisle complying with Section 11B-502.3. Exception: Van parking spaces shall be permitted to be 108 inches (2743 mm) wide minimum where the access a isle is 96 inches (2438 mm) wide minimum. 11B-208 Parking. Where parking spaces are provided, parking spaces shall be provided in accordance with Section 11B-208. For the purposes of this section, electric vehicle charging stations are not parking spaces; see Section 11B-228.Exception: Parking spaces used exclusively for buses, trucks, other delivery vehicles, or vehicular impoundshall not be required to comply with Section 11B-208 provided that lots accessed by the public are provided with a passenger loading zone complying with Section 11B-503. 11B-208.2 Minimum number. Parking spaces complying with Section 11B-502 shall be provided in accordance with Table 11B-208.2 except as required by Sections 11B-208.2.1, 11B-208.2.2, and 11B-208.2.3. Where more than one parking facility is provided on a site, the number of accessible spaces provided on the site shall be calculated according to the number of spaces required for each parking facility. 11B-403.3. Slope. The running slope of walking surfaces shall not be steeper than 1:20. The cross slope of walking surfaces shall not be steeper than 1:48.Exception: The running slope of sidewalks shall not exceed the general grade established for the adjacent street or highway. 11B-502.6 Identiﬁcation Parking space identiﬁcation signs shall include the International Symbol of Accessibility complying with Section 11B-703.7.2.1 in white on a blue background. Signs identifying van parking spaces shall contain addi-tional language or an additional sign with the designa-tion “van accessible”. Signs shall be 60 inches (1524 mm) minimum above the ﬁnish ﬂoor or ground surface measured to the bottom of the sign. 1. Outpatient units and facilities. Ten percent of the total number of parking spaces provided shall serve each such outpatient unit or facility. 2. Units and facilities that specialize in treatment or services for persons with mobility impairments. Twenty percent of the total number of parking spaces provided shall serve such unit or facility. 11B-502.2 Vehicle spaces. Car and van parking spaces shall be 216 inches (5486 mm) long minimum. Car parking spaces shall be 108 inches (2743 mm) wide minimum and van parking spaces shall be 144 inches (3658 mm) wide minimum, shall be marked to deﬁne the width, and shall have an adjacent access aisle complying with Section 11B-502.3. Exception: Van parking spaces shall be permitted to be 108 inches (2743 mm) wide minimum where the access aisle is 96 inches (2438 mm) wide minimum. 11B-502.3 Access aisle. Access aisles serving parking spaces shall comply with Section 11B-502.3. Access aisles shall adjoin an accessible route. Two parking spaces shall be permit-ted to share a common access aisle. 11B-502.3.2 Length. Access aisles shall extend the full required length of the parking spaces they serve. 11B-502.3.3 Marking. Access aisles shall be marked with a blue painted borderline around their perimeter. The area within the blue borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface, preferably blue or white. The words "NO PARKING" shall be painted on the surface within each access aisle in white letters a minimum of 12 inches (305 mm) in height and located to be visible from the adjacent vehicular way. Access aisle markings may extend beyond the mini -mum required length. 11B-502.6 Identiﬁcation. Parking space identiﬁcation signs shall include the International Symbol of Accessibility complying with Section 11B-703.7.2.1 in white on a blue background. Signs identifying van parking spaces shall contain addi-tional language or an additional sign with the designa-tion “van accessible”. Signs shall be 60 inches (1524 mm) minimum above the ﬁnish ﬂoor or ground surface measured to the bottom of the sign.. 11B-502.6.2 Minimum ﬁne. Additional language or an additional sign below the International Symbol of Accessibility shall state “Mini-mum Fine $250”. 11B-502signage 11B-502 80” OR 60” IFINSTALLEDON WALL FIGURE 11B-503.3 ACCESS AISLE AT PASSENGER LOADING ZONES FIGURE 11B-502 PARKING PEDESTRIAN ROUTE70 SQ INCHEACCESSIBILITY FOR DETECTABLEWARNINGREQUIREMEMNTSAT CURB RAMPSSEE SECTION11B-247 NOTE: THE LOADING ANDUNLOADING ACCESS AISLLESHALL BE MARKED BY A BORDER PAINTED BLUE. WITHIN THE BLUE BORDERHATCHED LINES A MAXIMUMOF 36 INCHES ON CENTERSHALL BE PAINTED A COLOR CONTRASTING WITH THEPARKING SURFACE.PREFERABLY BLUE OR WHITE. WITHIN THEACCESSIBLEPARKING STALLPAINT THE WORDS“NO PARKING” IN12” HIGHLETTERS MIN. WITHIN THEACCESSIBLEPARKING STALLPAINT THE WORDS“NO PARKING” IN12” HIGHLETTERS MIN. 5’-0” MIN. AT TYP.ACCESSIBLEPARKING STALL.8’-0” MIN. AT VANACCESSIBLEPARKING STALL WHEEL STOP WHEEL STOP TYPPAVEMENTUNIVERSALSYMBOLPER SEC TYPPAVEMENTSYMBOLPER SEC.1129B.4 STRIPES AT36” ONCENTER STRIPES AT36” ONCENTER NOPARKING PEDESTRIAN ROUTE 60 ” M I N UN L O A D I N G AR E A 240” MIN 2’-0” 9’-0” MIN 9’-0” MIN 9’-0” MIN 18 ’ M I N . 18 ’ M I N . 3’-0” 3’ - 0 ” VANACCESSIBLE PARKING ONLYMINIMUM FINE $250 PARKING ONLY MINIMUM FINE $250 PARKING ONLY VAN ACCESSIBLE UNAUTHORIZED VEHICLESPARKED IN DESIGNATEDACCESSIBLE SPACES NOTDISPLAYING DISTINGUISHINGPLACARDS OR SPECIALLICENSE PLATES ISSUED FORPERSONS WITH DISABILITIESWILL BE TOWED AWAY ATTHE OWNERS EXPENSE.TOWED VEHICLES MAY BERECLAIMED BY TELEPHONINGTHE _________ POLICEDEPARTMENT AT (___) ___-____ CVC 22658a MINIMUMFINE $250 70 SQ INCHEACCESSIBILITY NOPARKING BLUE REFLECTORIZED SIGN CONSTRUCTED OF PORCELAIN STEEL WITH BEADED TEXT OR EQUAL NOTE: AREA OF SIGN TO BE A MINIMUM OF 70 SQ. INCHES. DESIGNATED FOR “VAN ACCESSIBLE” WHERE APPROPRIATE STATEMENTREQUIREDBY ITEM 2OF SECTION VIIMAY BE COMBINEDWITH THIS SIGN 1/2” RADIUS WHITE WHERE APPLIES 80” MIN. FOR FREE STANDING TO TOP OF WALKING SURFACE SIGN INSTALLED AT EACH SPACE 60” MIN. FOR WALL MOUNTED VANACCESSIBLE PARKING ONLYMINIMUM FINE $250 RUBBER BUMPER ON CHAIR 10” MIN.BOTTOM RAIL DOOR (a) 60 INCHES DIAMETER SPACE MINIMUM CLEARWIDTH FOR A SINGLE WHEELCHAIR MINIMUM CLEARWIDTH FOR TWO WH EELCHAIR 60” 12” MIN. 12” MIN. 36” MIN. 36” MIN.60” MIN. 32” MIN. 60 ” 36 ” M I N . 24 ” M A X 60 ” O R L O N G E R CO N T I N U O U S P O I N T 60 ” M I N . THIS DIAGRAM ILLUSTRATES THE SPECIFIC REQUIREMENTSOF THESE REGULATIONS AND ARE INTENDED ONLY AS ANAID FOR BUILDING DESIGN AND CONSTRUCTION PER 11B-404 DOORS ACCESSIBILITYDETAILSFOR DOORS &MANEUVERINGSPACES THIS DIAGRAM ILLUSTRATES THE SPECIFIC REQUIREMENTS OFTHESE REGULATIONS AND ARE INTENDED ONLY AS AN AID FORBUILDING DESIGN AND CONSTRUCTION FIGURE 11B-304WHEELCHAIR TURNING SPACE CURB RAMPS UP UP SIDE ELEVATION11B-606 PLAN VIEW NOTE: if a minimum of 9 inches height of toe clearance is provided, a maximum of 6 inches of the 48 inches of clear ﬂoor space required at the ﬁxture may extend into the toe space 25” MAX.17” MIN. 48” MIN. 17” MIN. 18 ” M I N . TO C E N T E R L I N E 30 ” M I N . 19” MAX. 9 ” M A X . 27 ” M A X . 29 ” M A X . 34 ” M A X . 40 ” M A X . 6” MAX.8” MIN. KNEE CLEARANCE TOE CLEARANCE NOTE: HOT WATER AND DRAIN PIPES UNDER LAVATORY SHALL BE INSULATED. CLEAR FLOOR SPACE SIGNS and IDENTIFICATION (PER SECTION 11B-703 SIGN, 2013 BUILDING CODE). - INTERNATIONAL SYMBOL OF ACCESSIBILITY. The international symbol of accessibility shall consist of a white ﬁgure on a blue background and be the standard used to identify facilities that are accessible to and usable by physically disabled persons as set forth in standards and as speciﬁcally required in this section. Exception: Signs need not be provided for facilities within an adaptable dwelling unit or within an accessible patient or guest room. - COLOR OF SYMBOL The symbol speciﬁed above shall consist of a white ﬁgure on a blue background. The blue color shall be equal to Color No. 15090 in Federal Standard 595B. Exception: The appropriate enforcement agency may approve signs and identiﬁcation necessary to compliment decore or unique design when it is determined that such signs provide adequate directions to persons with disabilities. - BRAILLE SYMBOLS Contracted Grade-2 braille shall be used wherever braille symbols are speciﬁcally required in other portions of those standards. Dots shall be 1/10 inch (2.54 mm) each cell with 2/10 inch (5.08 mm) space between cells. Dots shall be raised a minimum of 1/40 inch (0.635 mm) above the background. - PROPORTIONS Letter and numbers on signs shall have a width-to-heigth ratio of between 3:5 and 1:1 and a stroke width-to-heigth ratio between 1:5 and 1:10. - CHARACTER HEIGHT Characters and numbers on signs shall be sized according to the viewing distance from which they are to be read. The minimum height is measured using a sign where lowercase characters are permited. For signs suspended or projected above the ﬁnished ﬂoor in compliance with section 11B-703 - CONTRAST OF SYMBOL Characters and Symbols shall contrast with their background, either light characters on a dark background or dark characters on a light background. - RAISED CHARACTERS AND PICTORIAL SYMBOL SIGNS Whan raised characters or symbols are used they shall conform to the following requirements: 1. Letter type - Letters and numbers on signs shall be raised 1/32 inch (.794 mm) min. and shall be sans-serif uppercase characters acompanied by Grade 2 Braille 2. Symbol size - Raised characters or symbols shall be a min. of 5/8 inch (15.9 mm) high. 3. Pictorial symbol signs (Pictograms) - Pictorial symbol signs (Pictograms), shall be accompanied by the equivalant verbal description placed directly below the pictogram. The border of the pictogram shall be a min. of 6 inches (162 mm) in height. - ENTRANCE SIGNS All building Entrances that are accessible to and usable by persons with disabilities shall be identiﬁed with at least one standardsign and with additional direction signs as required to be visible to persons along approaching pedestrian ways. - INFORMATION POSTED Buildings that have been remodeled to provide speciﬁc sanitary facilities and/or elevators for public use that conform to thosebuildings standards shall have signs posted in the buildings lobby, preferably part of the building directory. - MOUNTING LOCATION AND HEIGHT • Where permanent identiﬁcation is provided for rooms and spaces, raised letters shall be provided and shall be accompanied by Braille in compliance with section 11B-703 • Signs shall be installed on the wall adjacent to the latch outside of the door. • Where there is no wall space on the latch side, including at double-leaf doors, signs shall be placed on the nearest adjacent wall, preferably on the right. • Mounting height shall be 60 inches (1524 mm) above the ﬁnished ﬂoor to the centerline of the sign. • Mounting location shall be determined so that a person may approach within 3 inches (76 mm) of signage without encountering pertruding objects or standing within the swing of a door. - TRAFIC CONTROL DEVICES Pole supported traﬃc control buttons shall be identiﬁed with color coding consisting of a textured horizontal yellow band 2 inches (51 mm) wide encircling the pole and a 1 inch wide (25 mm) darkborder band above and below the yellow band. Color coding should be placed immediately above the control button. Control buttons should be no higher than 48 inches (1219 mm) above the surface adjacent to the pole. TACTILE EXIT SIGNS: (Tactile Exit Signes Shall Be Required At The Following Locations.) 1 - Each grade level exterior door that is required shall be identiﬁed with a Tactile Exit Sign with the word “EXIT.” 2. - Each exit door that leads directly to a grade-level exterior exit by means of a stairway or ramp shall be identiﬁed by a Tactile Exit Sign with the following words as appropriate... 3. - Each exit door that leads directly to a Grade-Level exit by means of an exit enclosure that does not utilize a stair or ramp passagway shall be identiﬁed by a Tactile Exit Sign with the words “EXIT ROUTE”. 4. - Each exit door from an interior room or area shall be identiﬁed by a Tactile Exit Sign with the words “EXIT ROUTE”. 5. - Each exit door through a horizontal exit shall be identiﬁed by a Tactile Exit Sign with the words “TO EXIT”. 12 ” 3/8” MIN. TO 1/2” MAX. 3/8” MIN TO 1/2” MAX. 12” 12” 1/4” 1/4” SECTION TACTILE RESTROOM SIGNAGE ANDCONTRASTING RESTROOM SYMBOLS TACTILE EXIT ROUTE AND EXIT SIGNS Signs with raised characters and braille shall be located 48 inches (1220 mm) minimum above the ﬁnish ﬂoor or ground surface,measured from the baseline of the lowest line of Braille and 60 inches (1525 mm) max. above the ﬁnish ﬂoor or ground surface,measured from the baseline of the highest line of raised characters. Mounting location shall be determined so that a person mayapproach within 3 inches (76 mm) of signage without encountering protruding objects or standing within the swing of a door. NOTE: TACTILE SIGNS CORRESPONDING TO GRADE II - BRAILLE COMPLIANCE ACCESSIBLE SIGNAGE AN ADULT SIZE WHEELCHAIRAVERAGES 27 INCHES IN WIDTH.THE REQUIRED 32 INCH CLEAROPENING ALLOWS 2-1/2 INCHESON EACH SIDE FOR HANDS TWO CONDITIONS SHOWN BELOW OFTEN MAKESPATHS UNACCESSIBLE TO WHEELCHAIRS. INADEQUATELY SECURED DROPMATS INTERFERE WITHWHEELCHAIR TRAFFIC THRESHOLDSPER SECTION 303 DOOR MAT 1/2” MAX. AT 1:2 SLOPE 1/4” MAX. 2 1 COMPRESSED CARPET1/4” MAX. BELOWTHRESHOLD FINISH FLOOR EVEN THRESHOLD 12”LOCATE CLOSER ONRESTROOM SIDE OF DOOR ON DOORWAYS LEADING TOMEN’S SANITARY FACILITIES, ANEQUILATERAL TRIANGLE 1/4INCH THICK, 12 INCHES LONGAND A VERTEX POINTING UPWARDSHALL BE PROVIDED AND ONDOORS LEADING TO WOMEN’S SANITARY FACILITIES A CIRCLE1/4 INCH THICK AND 12 INCHESIN DIAMETER SHALL BE PROVIDED.THESE GEOMETRIC SYMBOLS SHALL BE CENTERED ON THE DOORAT A HEIGHT OF 60 INCHES ANDTHEIR COLOR AND CONTRASTSHALL BE DISTINCTLY DIFFERENTFROM THE COLOR AND CONTRASTOF THE DOOR. DISABLESIGNAGE 3 ’ - 2 ” 5’ - 0 ” 12 ”12” KICKPLATES ONBOTH SIDES OF DOOR HARDWARE LEVEL (TYP.) 11B-703 SIGNAGE F.F. BRAILLE SIGN GRAB BAR SECTION WALL (3) 1/4” Dia. x 2”Long Lag Screws 2” XBlocking 1-1/4”TO1-1/2”NOMINALDIAMETER 1-1/2” 24 ” M I N . 19” MIN. 33 ” M I N 36 ” M A X 33 ” M I N 36 ” M A X 42” MIN. GRAB BAR 36” MIN. GRAB BAR ALL DISPENSERS40” MAX TOHIGHESTOPERABLE PART SIDE WALL ELEVATION 54” MIN. 17”-19” 12” MAX 12” MIN CL 7” - 9” REAR WALL ELEVATION REAR GRAB BARALLOWED AT 36” A.F.F.AT TANK-TYPE TOILET TRANSFERSIDE 17”-18” FIGURE 11B-213.3 CLEAR OPENINGS FOR TWO FRONT DOORS MUST BE BETWEEN EITHER DOOR IN IT’S 90 DEGREE OPEN POSITION AND THE ANGLE OF THE OTHER DOOR. 32” CLR 90° double door TOP OFGRABBAR 11B-406.3 - PARALLEL CURB RAMPS. PARALLEL CURB RAMPS SHALL COMPLY WITH SECTIONS 11B-406.3 AND 11B-406.5 11B-406.3.1 - SLOPE. THE RUNNING SLOPE OF THE CURB RAMP SEGMENTS SHALL BE IN-LINE WITH THE DIRECTION OF THE SIDEWALK TRAVEL. RAMP RUNS SHALL HAVE A RUNNING SLOPE NOT STEEPER THAN 1:12. 11B-406.3.2 - TURNING SPACE. A TURNING SPACE 48 INCHES (1219 mm) MINIMUM BY 48 INCHES (1219 mm) SHALL BE PROVIDED AT THE BOTTOM OF THE CURB RAMP. THE SLOPE OF THE TURNING SPACE IN ALL DIRECTIONS SHALL BE 1:48 MAXIMUM. 11B-406.5 - COMMON REQUIREMENTS. CURB RAMPS AND BLENDED TRANSITIONS SHALL COMPLY WITH SECTION 11B-406.5. 11B-406.5.1 - LOCATION. CURB RAMPS AND THE FLARED SIDES OF CURB RAMPS SHALL BE LOCATED SO THAT THEY DO NOT PROJECT INTO VEHICULAR TRAFFIC LANES, PARKING SPACES OR PARKING ACCESS ISLES. CURB RAMPS AT MARKED CROSSINGS SHALL BE WHOLLY CONTAINED WITHIN THE MARKINGS, EXCLUDING ANY FLARED SIDES. 11B-406.5.2 - WIDTH. A TURNING SPACE 48 INCHES (1219 mm) MINIMUM BY 48 INCHES (1219 mm) SHALL BE PROVIDED AT THE BOTTOM OF THE CURB RAMP. THE SLOPE OF THE TURNING SPACE IN ALL DIRECTIONS SHALL BE 1:48 MAXIMUM. EXCEPTION: DIAGONAL CURP RAMPS SHALL COMPLY WITH SECTION 11B-406-5.9 11B-406.5.3 - LANDINGS. LANDINGS SHALL BE PROVIDED AT THE TOPS OF CURB RAMPS & BLENDED TRANSITIONS. THE LANDING CLEAR LENGTH SHALL BE 48 INCHES (1219 mm) MINIMUM. THE LANDING CLEAR WIDTH SHALL BE AT LEAST AS WIDE AS THE CURB RAMP, EXCLUDING ANY FLARED SIDES, OR THE BLENDED TRANSITION LEADING TO THE LANDING. THE SLOPE OF THE LANDING IN ALL DIRECTIONS SHALL BE 1:48 MAX. EXCEPTION: PARALLEL CURB RAMPS SHALL NOT BE REQUIRED TO COMPLY WITH SECTION 11B-406.5.3 11B-406.5.4 - FLOOR OR GROUND SURFACES. FLOOR OR GROUND SURFACES OF THE CURB RAMPS SHALL & BLENDED TRANSITIONS COMPLY WITH SECTION 11B-405-4 11B-406.5.5 - WET CONDITIONS. CURB RAMPS SHALL AND BLENDED TRANSITIONS COMPLY WITH SECTION 11B-405-10. 11B-406.5.6 - GRADE BREAKS. GRADE BREAKS AT THE TOP AND BOTTOM OF CURB RAMP RUNS SHALL BE PERPENDICULAR TO THE DIRECTION OF THE RAMP RUN. GRADE BREAKES SHALL NOT BE PERMITTED ON THE SURFACE OF RAMP RUNS AND TURNING SPACES. SURFACE SLOPES THAT MEET GRADE BREAKS SHALL BE FLUSH. 11B-406.5.7 - CROSS SLOPE. THE CROSS SLOPE OF CURB RAMPS AND BLENDED TRANSITIONS SHALL BE 1:48 MAX. 11B-406.5.7 - COUNTER SLOPE. COUUNTER SLOPES OF ADJOINING GUTTERS AND ROAD SURFACES IMMEDIATELY ADJACENT TO AND WITHIN 24 INCHES (610mm) OF THE CURB RAMP SHAL NOT BE STEEPER THAN 1:20. THE ADJACENT SURFACES AT TRANSITIONS AT CURB RAMPS TO WALKS, GUTTERS AND STREETS SHALL BE AT THE SAME LEVEL. 12” 12” 18” 144” MIN VAN 8’ MIN 108” MIN CAR ADA PARKING SIGNAGE WALKWAY DECTECTABLEWARNING(SEE - 9A) 48” x 48”MINIMUMLANDING AREA 36 ” MI N . CURB RAMP 36” MIN. 18 ’ M I N I M U M Figure 11B-705.1 Size and Spacing of Truncated Domes 11B-705.1.1.3 Color and Contrast Detectable warning surfaces at transit boarding platform edges, bus stops, hazardous vehicular areas, reﬂecting pools, and track crossings shall comply with Section 11B-705.1.1.3.1. Detectable warnings at other locations shall comply with either Section 11B-705.1.1.3.1 or Section 11B-705.1.1.3.2. The material used to provide visual contrast shall be an integral part of the surface. 11B -705.1.1.3.1 Detectable warning surfaces shall be yellow andapproximate FS 33538 of Federal Standard 595C. 11B -705.1.1.3.2 Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking surfaces. 30 ” WI D E M I N . 27 ” HI G H M I N . 19” DEEP MIN. ACCESSIBLE FIXED TABLE SEATING - CBC 11B-306 30” X 48” CLR AREA 18 ” 10 ’ - 0 ” 18”. 64” 18 ” 18”. 65” 9’-0” 10 ’ - 0 ” 8’-0” BATHRM 1 BATHRM 2 60” R 60” R 18” Min.32” Min. CLR 18” Min.32” Min. CLR 30” X 48” CLR AREA FLUSH ACTIVATORON WIDE SIDE CENTERLINEOFFIXTURE 2 4 ” M i n . 1 2 ” M A X . 36 ” M I N 60 ” M I N . 2 4 ” M i n . 12 ” M A X . 36 ” M I N 60 ” M I N . MEZZANINESUPPORT POST FLUSH ACTIVATORON WIDE SIDE CENTERLINEOFFIXTURE CENTERLINEOFFIXTURE MEZZANINESUPPORT POST CENTERLINEOFFIXTURE SINGLE ACCOMMODATIONTOILET FACILITY FIGURE 11B-604 60 ” MI N . 60 ” MI N . Figure 11B-404.2.3Clear Width of Doorways Figure 11B-404.2.3Clear Width of an Accessible Route 8 5 7 3 1 4 1A 9A 9 2 D A V E G A M B O A AE S S o l u t i o n s L L C Lo n g B e a c h , C A 9 0 8 1 3 71 4 - 5 9 7 - 5 5 6 0 Si g n e d : 0 3 / 0 5 / 2 0 2 4 DA T E : 2 0 2 4 - 0 4 - 2 9 SC A L E : A S N O T E D J O B # : DR A W N B Y : D R G S n i p s C u l t i v a t i o n L L C Me r r e t t S c o t t - P r e s & C E O 32 0 1 S . H a l l a d a y Sa n t a A n a , C A 9 2 7 0 5 (9 4 9 ) 2 8 5 - 2 0 5 7 m e r r e t t . r . s c o t t @ g m a i l . c o m S n i p s C u l t i v a t i o n 3 2 0 1 S . H a l l a d a y S a n t a A n a , C A 9 2 7 0 5 EXISTING ADA ACCESSIBILTY - NOTES & DETAILS (UNDER PERMIT #101113395) 9/ 3 0 / 2 0 2 5 03 - 1 5 - 2 0 2 4 3201 S Halladay St 5/5/2025