|
4"
<br />c.c.1 1/4"
<br />HORIZ.
<br />BRACE
<br />DIAG.
<br />BRACE
<br />CONNECTOR
<br />BASE
<br />PLATE &
<br />ANCHOR
<br />COLUMN
<br />ROW
<br />SPACER BEAM
<br />SEE ATTACHED
<br />PREMIER WAREHOUSE PERMITS INC DWG.
<br />FOR STORAGE RACK ELEVATIONS
<br />1 5/8"
<br />3 1/4"
<br />1"1 1/2"
<br />12"
<br />3/8"Ø X 7/8" SLOT
<br />4 PLCS
<br />3/4"1 1/2"
<br />3/4"
<br />11/16"
<br />3/4"
<br />3-5/8"
<br />3-1/4"
<br />MIN. EMBED.
<br />1/2"
<br />BASE PLATE F.F.
<br />O.A.L.
<br />1 11/16"
<br />6"
<br />1"
<br />3 3/16"
<br />2"
<br />2"
<br />7/16" Ø GR.
<br />55 RIVET
<br />5/16" Ø
<br />SAFETY PIN
<br />1"
<br />1"
<br />8"
<br />5"
<br />3/8"
<br />5/8"Ø
<br />3"
<br />3"
<br />3/4"
<br />1 5/8"
<br />4"
<br />1"1 1/2"
<br />1 11/16"
<br />8"
<br />1"
<br />3 3/16"
<br />2"
<br />2"
<br />2"
<br />7/16" Ø GR.
<br />55 RIVET
<br />5/16" Ø
<br />SAFETY PIN
<br />DESCRIPTION
<br />STEEL YIELD
<br />MATERIAL NOTES:
<br />USE @ ALL BOLTED HANNIBAL BRACE
<br />LOCATIONS TYP .ASTM A570, Fy=55,000 PSI
<br />16 GAGE STEEL
<br />BRACING: HORIZ. & DIAG.NOT A DEPICTION OF THIS PROJECT
<br />GENERAL RACK INFORMATION1
<br />NOTES:
<br />USE @ TYPE A BEAM LOCATIONS.
<br />15 GAGE
<br />STEEL YIELD
<br />MATERIAL
<br />DESCRIPTION
<br />ASTM A570, Fy=55,000 PSI
<br />3-1/4" BEAM (STEPBEAM)
<br />MATERIAL
<br />STEEL YIELD
<br />DESCRIPTION STD ROW SPACER
<br />ASTM A570, Fy =55,000 PSI
<br />16 GAGE
<br />NOTES:
<br />ATTACH WITH (4) 3/8"Ø GR. 5 BOLTS,
<br />(2) @ EACH END
<br />SIZE 1/2"Ø x 3-1/4 MIN. EMBED.
<br />HILTI KWIKBOLT TZ2 ANCHOR
<br />NOTES:
<br />SEE NOTE #4 ABOVE FOR ANCHOR SPECS.
<br />DESCRIPTION
<br />ESR # 4266
<br />DESCRIPTION STORAGE RACK ELEVATIONS
<br />7 GAGE
<br />3-PIN CONNECTOR
<br />ASTM A570, Fy=55,000 PSISTEEL YIELD
<br />MATERIAL
<br />DESCRIPTION NOTES:
<br />USE @ TYPE A BEAM TO COLUMN
<br />CONNECTION LOCATIONS.
<br />GENERAL PROJECT NOTES
<br />1. DESIGNED PER REQUIREMENTS OF THE 2022 CBC, ASCE 7-16, SECTION 15.5.3, & 2012 RMI RACK DESIGN MANUAL
<br />2. SEISMIC CRITERIA SS =1.289, S1 =0.453, FA = 1.200, FV = 1.850
<br /> IP = 1.0 (NO PUBLIC ACCESS), SDS = 1.031, SD1 =0.559, OCCUPANCY CATAG. II
<br /> SITE CLASS D-DEFAULT, SEISMIC DESIGN CATAG. D
<br />3. STORAGE CAPACITY:
<br /> TYPE A=3000 LBS PER LEVEL TYP.
<br /> TYPE B=2000 LBS PER LEVEL TYP.
<br />4. ANCHORS : HILTI KWIKBOLT TZ2 ESR#4266, OR POWERS SD2 ESR#2502
<br /> 1/2" Ø X 3-1/4" MIN. EMBEDT.
<br /> 50 FT-LBS TORQUE (HILTI KWIKBOLT TZ2)
<br /> 40 FT-LBS TORQUE (POWERS SD2)
<br /> (2) ANCHORS PER BASE PLATE.
<br />5. PERIODIC SPECIAL INSPECTION IS REQUIRED DURING ANCHOR INSTALLATION. ANCHORS SHALL BE INSTALLED
<br /> PER ICC ESR#4266.
<br />6. EXISTING S.O.G. CONCRETE THICKNESS & COMPRESSIVE STRENGTH, 6" X 2500 PSI
<br />7. SOIL BEARING PRESSURE 750 PSF.
<br />8. ALL RACK INSTALLATIONS AND RACKS MANUFACTURED IN CONFORMITY WITH THIS STANDARD SHALL DISPLAY IN
<br /> ONE OR MORE CONSPICUOUS LOCATIONS A PERMANENT PLAQUE EACH NOT LESS THAN 50 SQUARE
<br /> INCHES IN AREA AND SHOWING THE MAXIMUM PERMISSIBLE UNIT LOAD IN CLEAR, LEGIBLE PRINT.
<br />9. ALL BOLTS GR. 5 OR BETTER, INSTALL TO SNUG TIGHT FIT OR BETTER
<br />10. ALL WELDING PERFORMED IN THE SHOP OF AN APPROVED FABRICATOR BY AWS CERTIFIED WELDERS USING E70XX
<br /> ELECTRODE OR BETTER. NO FIELD WELDING PERFORMED. SPECIAL INSPECTION IS REQUIRED ONLY FOR ANY FIELD
<br /> WELDING.
<br />11. THE CLEAR SPACE BELOW SPRINKLERS SHALL BE A MIN. OF 18" BETWEEN TOP OF THE STORAGE AND THE
<br /> CEILING SPRINKLER DEFLECTOR.
<br />12. THE PRODUCT SHOWN ON THE DETAILS HEREIN IS ASSUMED TO BE IN GOOD, UNDAMAGED CONDITION. THE
<br /> PRODUCT MUST BE FREE OF ANY DAMAGE AND/OR FABRICATION DEFICIENCIES OR IRREGULARITIES. IT IS THE
<br /> RESPONSIBILITY OF THE OWNER, USER, PRODUCT PROVIDER AND/OR INSTALLER OF THE COMPONENTS TO
<br /> NOTIFY SED, INC IN WRITING, OF ANY DAMAGE, DEFICIENCIES OR IRREGULARITIES.
<br />13. IT IS THE RESPONSIBILITY OF THE OWNER AND/OR USER OF THE COMPONENTS SHOWN HEREIN TO NOTIFY SED,
<br /> INC OF ANY DAMAGE OR DEFICIENCIES IN THE SYSTEM DURING USE.THIS INCLUDES SUCH OCCURRENCES
<br /> SUCH AS IMPACT DAMAGE TO THE COMPONENTS FROM FORKLIFT OR HEAVY MACHINERY, IMPACT FROM
<br /> DROPPED LOADS ON THE SYSTEM, DAMAGE TO SYSTEMS BY IMPROPER USE OR INSTALLATION, ETC. THE USER
<br /> OF THE PRODUCT MUST NOTIFY SED, INC IN WRITING SHOULD ANY DAMAGE OR DEFICIENCY OCCUR TO THE
<br /> PRODUCT SHOWN HEREIN. IT IS THE RESPONSIBILITY OF THE OWNER AND/OR USER TO MAINTAIN THE SAFETY
<br /> AND PROPER USE OF THE STORAGE PRODUCT SHOWN HEREIN.
<br />14. IT IS THE RESPONSIBILITY OF THE OWNER/USER OF THE STORAGE SYSTEM SHOWN HEREIN TO REPAIR OR
<br /> REPLACE ANY COMPONENT THAT IS DAMAGED OR OTHERWISE DEFICIENT.
<br />15. THE OWNER SHALL MAINTAIN THE STRUCTURAL INTEGRITY OF THE RACK SYSTEM BY ASSURING PROPER
<br /> OPERATIONAL, HOUSE KEEPING AND MAINTENANCE PROCEDURES, BUT NOT LIMITED TO THE FOLLOWING:
<br /> A. PROHIBIT ANY OVER LOADING OF ANY PALLET POSITIONS AND OF OVERALL RACK SYSTEMS.
<br /> B. REGULARLY INSPECT FOR DAMAGE. IF DAMAGE IS FOUND, IMMEDIATELY UNLOAD THE AFFECTED AREA AND
<br /> REPLACE OR REPAIR ANY DAMAGED COLUMNS, BEAMS, OR OTHER STRUCTURAL COMPONENTS.
<br /> C. REQUIRE ALL PALLETS TO BE MAINTAINED IN GOOD, SAFE, OPERATING CONDITION.
<br /> D. ENSURE THAT PALLETS ARE PROPERLY PLACED ONTO PALLET LOAD SUPPORT MEMBERS IN PROPERLY STACKED
<br /> AND STABLE POSITION.
<br /> E. REQUIRE THAT ALL GOODS STORED ON EACH PALLET TO BE PROPERLY STACKED AND STABLE.
<br /> F. PROHIBIT DOUBLE STACKING OF ANY PALLET POSITION, INCLUDING THE TOP MOST POSITION, UNLESS THE RACK
<br /> SYSTEM IS SPECIFICALLY DESIGNED FOR SUCH LOADING.
<br /> G. THE OWNER AND/OR USER OF THE RACK SYSTEM MUST PROVIDE MEASURES TO MITIGATE DAMAGE TO THE
<br /> STORAGE RACK BY USE OF IMPACT PROTECTIVE DEVICES IN AREAS WHERE FORKLIFT AND/OR HEAVY MACHINERY
<br /> ARE IN USE.
<br /> H. ENSURE THAT THE RACKS ARE NOT MODIFIED OR REARRANGED IN A MANNER NOT WITHIN THE ORIGINAL DESIGN
<br /> CONFIGURATION.
<br />16. THE MAXIMUM TOP TO BOTTOM OUT-OF-PLUMB RATIO AND OUT-OF-STRAIGHT RATIO RACK COLUMN IS 1/240 (FOR
<br /> EXAMPLE 1/2" PER 10 FEET OF HEIGHT). COLUMN WHOSE OUT-OF-PLUMB RATIO OR OUT-OF-STRAIGHT RATIO
<br /> EXCEEDS THIS LIMIT SHOULD BE UNLOADED AND RE-PLUMBED. ANY DAMAGED PARTS MUST BE REPAIRED OR
<br /> REPLACED.
<br />17. MINIMUM DISTANCE BETWEEN RACK AND BUILDING COMPONENTS IS 2% (OR 3.84") OF TOP SHELF LEVEL
<br /> HEIGHT @ BRACED DIRECTION AND 5% (OR 9.6") OF TOP SHELF LEVEL HEIGHT @ UNBRACED DIRECTION.
<br />18
<br />1
<br />5
<br />
<br />W
<br />R
<br />I
<br />G
<br />H
<br />T
<br />
<br />A
<br />V
<br />E
<br />.
<br />
<br />L
<br />A
<br />
<br />V
<br />E
<br />R
<br />N
<br />E
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />1
<br />7
<br />5
<br />0
<br />
<br />P
<br />H
<br />O
<br />N
<br />E
<br />
<br />9
<br />0
<br />9
<br />.
<br />5
<br />9
<br />6
<br />.
<br />1
<br />3
<br />5
<br />1
<br />
<br />F
<br />A
<br />X
<br />
<br />9
<br />0
<br />9
<br />.
<br />5
<br />9
<br />6
<br />.
<br />7
<br />1
<br />8
<br />6
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />24-0326-19
<br />SED 1 OF 1
<br />04
<br />/
<br />0
<br />2
<br />/
<br />2
<br />0
<br />2
<br />4
<br />UN
<br />I
<br />C
<br />O
<br />R
<br />N
<br />J.
<br />M
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />ST
<br />O
<br />R
<br />A
<br />G
<br />E
<br />
<br />R
<br />A
<br />C
<br />K
<br />SA
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />5
<br />29
<br />0
<br />1
<br />
<br />D
<br />A
<br />I
<br />M
<br />L
<br />E
<br />R
<br />
<br />S
<br />T
<br />NOTES:
<br />USE (2) STD ROW SPACERS FOR DOUBLE ROW
<br />NOTES:
<br />CONFIRM O.A.L. OF ANCHORS WITH INSTALLER TO
<br />ENSURE REQUIRED EMBEDMENT IS OBTAINED.
<br />COLUMN
<br />NOTES:
<br />USE @ ALL UNICORN
<br />COLUMN/BASE LOCATIONS TYP.
<br />STEEL YIELD
<br />DESCRIPTION
<br />MATERIAL
<br />BASE PLATE: 8" x 5"
<br />3/8" THICK PLATE
<br />ASTM A36, Fy=36,000 PSISTEEL YIELD
<br />DESCRIPTION
<br />MATERIAL
<br />ASTM A570, Fy=55,000 PSI
<br />14 GAGE THK.
<br />COLUMN: UNICORN C3314TD
<br />2
<br />3 5 6
<br />8
<br />1B
<br />NOTES:
<br />USE @ TYPE B BEAM LOCATIONS.
<br />15 GAGE
<br />STEEL YIELD
<br />MATERIAL
<br />DESCRIPTION
<br />ASTM A570, Fy=55,000 PSI
<br />4" BEAM (STEPBEAM)
<br />4
<br />7 GAGE
<br />4-PIN CONNECTOR
<br />ASTM A570, Fy=55,000 PSISTEEL YIELD
<br />MATERIAL
<br />DESCRIPTION NOTES:
<br />USE @ TYPE B BEAM TO COLUMN
<br />CONNECTION LOCATIONS.
<br />7
<br />04/03/24
<br />(6)6,2 251$3 /'((15
<br />*(7 ,16,(*((55
<br />$&/),)2 2(571$,7 $6 9 ,,/&
<br />((55
<br />$&/),)2 2(555555555555555555555555555555555555555555555555555555555777777777777777777777777777777777777777777777777111111111111111111111111111111111111111111111111111111111$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,7$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$66666666666666666666666666666666666666666666666 9 ,,/////////////&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&
<br />1R1R
<br />(([S[S
<br />HOLD- 2901 S
<br />Daimler St12/11/2024
|