|
October 1, 2013 SIGN COMPONENTS MANUAL (SAM)112
<br />ARCADIA WEST INDUSTRIAL PARK
<br />9735 COMMERCE CIR
<br />KUTZTOWN, PA 19530
<br />Rigid Sign Face Materials, designated Palsun, Palsun SG and Palsun CS.
<br />1. These materials are acceptable for applications of sign enclosures, sign bodies, and decorative parts. For enclosure
<br />applications, these materials may be located no closer than 0.8 mm to any uninsulated live part.
<br />2. The materials have a use temperature of 80"C. If a heat producing component such as electroda, transformer or ballast is
<br />located within 1 inch of the material. a temperature test should be conducted in the end product.
<br />3. Marking - The following markings or equivalent shall be provided. Markings A and B below shall be marked anywhere where
<br />readilyvisible during servicing.
<br />A. "Do not attempt to repair or service a damaged sign face. For servicing of this sign, contact ." (Blank to be replaced by
<br />Applicant's Company name, City and State.)
<br />B. "Replace only with -, Type - 7 (Blanks to be replaced by Applicant's Company name and material Type or
<br />designation.)
<br />4. The materials are suitable for use as an encloswre of an indoor or outdoor:sign and have been evaluated for ozon@ resistance
<br />and UV exposure.
<br />5. All materials must be a minimum of 0.12 in. (3.0 mm) thick to comply as a sign enclosure. All testing should be repeated if the
<br />thickness of the sheet is reduced to less than 0.12 in. (3.Omm).
<br />6. All materials have been investigated fer and comply with the termination of conduit, electrode housings or the like.
<br />7. All materials have been approved for component support when components are secured by nuts and bolts.
<br />8. The suitability of the securement system for the materials to puevent the entrance of water, which may contact live parts withih a
<br />sign in outdoor sign applications, shall be determined.
<br />9. When the material is relied upon for the mounting of the sign and/or sign components, the material shall be subjected to the
<br />mounting means test in the end product.
<br />10. Only one side of the plastic sheets are UV coated. Thefefore, the UV coated side shall be placed such that it is the exterior
<br />surface of the sign
<br />11. Testing for exposure to live parts was conducted on the non-UV coated side of plastics. Thus, the non-UV coated side; shall be
<br />the only side exposed to live parts.
<br />12. The mounting system must secure the sign face to the enclosure in such a way that the edges of the sign face are not exposed
<br />to the interior of the sign. This may be accomplished with channels, flanges or other suitable mechanical means.
<br />PARMIDA LLC E362583
<br />801 E WASHINGTON BLVD
<br />LOS ANGELES, CA 90021
<br />Class 2 LED Modules, designated as XXXX YYYYD/M series, where XXXX and YYYY may be combinations of any numbers.
<br />1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
<br />2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
<br />limited circuits.
<br />3. When these units are connected to a Class 2 supply circuit, they are not to draw a total wattage of greater than the secohdary
<br />or output rating of the Class 2 sUpply.
<br />4. These products are suitable for use in dry, damp and wet locations.
<br />5. These products are not required to be enclosed or protected from the weather in the end product.
<br />5 These products may be secured in place in the end product by any means available.
<br />PERMLIGHT PRODUCTS INC
<br />422 W 6TH ST
<br />TUSTIN, CA 92780
<br />E213411
<br />Class 2 LED Illumination, Cat. Nos.700 Series, 752 ("Twister\'r") or PCSA01, 760-2,; 760-3, 765-4:, 750-5, 750-9, 711-2, 780
<br />Series, TINY2, PX Series.
<br />1. These products are only suitable for connectiom to a UL Listed or Recognized Class 2, 12 volt DC power source.
<br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
<br />and energy limited supplies.
<br />3. Class 2 LED Illumination, 700 Series is rated 0.6 Watts per unit, Cat. No. 750-9 is rated 1.44 watts per unit, Cat No. 750-5 is
<br />rated 0.6 watts per unit, Cat. No. 760-3 is rated 0.48 Watts per unit, Cat. No. 752 or PCSA01 is rated 0.6 per unit, and Cat. No
<br />765-4 is rated 0.6 per unit and Cat. No. 711-2 is rated 0.6 Watts per unit, Cat. No. TINY2 is rated 0.4 Watts per unit. When
<br />units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of
<br />the Class 2 supply and 60 watts per Clast 2 circuit.
<br />4. Class 2 LED Illumination, 700 Series and Tiny2 are provided with a RIC wire soldered on the printed wiring board for
<br />connection in series.
<br />5. Cat. No. 750-9,750-5,760-3,752 or PCSA01, 765-4 and 711-2 Series are Provided with R/C.wire soldered on theprinted
<br />wiring board for connectioh in series.
<br />6. These products are suitable for use in dry, damp and wet locations.
<br />7. These products are not required to be enclosed or protected from weather.
<br />Class 2 LED Illumination, Model No. 711-18DL
<br />1. These products are only suitable fer connection to a UL Listed or Recognized Class 2, 12 volt DC power source.
<br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
<br />and energy limited supplies.
<br />3. Class 2 LED Illumination, 711-18 el module is rated 60 Watts per unit. When units are connected to a Class 2 circuit, they are
<br />not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit.
<br />4. Cat. No. 711-18 DL modules are provided with R/C wire soldered on the printed wiring board for connection.
<br />5. These products are suitable for use in dry, damp and wet locations.
<br />6. These products are not required to be enclosed or protected from weather.
<br />/:SL\
<br />i
|