|
1. PROVIDE APPROVED SMOKE ALARMS, SMOKE ALARMS
<br />SHALL BE INTERCONNECTED SUCH THAT THE
<br />ACTIVATION OF ONE ALARM WILL ACTIVATE ALL ALARMS.
<br />2. SMOKE DETECTORS SHALL BE "HARD WIRED" AND SHALL
<br />BE EQUIPPED WITH BATTERY BACK-UP @ ALL NEW
<br /> BEDROOMS.
<br />3.THE SMOKE ALARMS SHALL BE INTERCONNECTED. (R314.4)
<br />4. FOR SINGLE-FAMILY DWELLINGS AND DUPLEXES ARE
<br />NOT CHECKED FOR PLUMBING, MECHANICAL AND
<br />ELECTRICAL CODE COMPLIANCE. THESE DISCIPLINES
<br />ARE SUBJECT TO FIELD INSPECTION.
<br />5. THE RESIDENCE SHALL CONFORM TO THE STATE
<br />ENERGY STANDARDS.
<br />NOTES:
<br />LEGEND
<br />110 v DUPLEX ELEC. OUTLET
<br />WATER PROOF
<br />HOSE BIBB W/ ANTI-SIPHONE
<br />WALL MOUNTED LIGHT
<br />CEILING MOUNTED LIGHT
<br />6" LED RECESS LIGHT
<br />CEILING FAN
<br />SINGLE POLE SWITCH
<br />SMOKE DETECTOR BATTERY (INTER-CONNECTED)
<br />S
<br />HB
<br />GROUND FAULT INTERUPTED CIRCUIT
<br />AFCI ARC FAULT CIRCUIT INTERRUPTER
<br />GFI
<br />EXHAUST FAN (100 CFM) W/ HUMIDITY CONTROL
<br />(MAX 3 SONE)
<br />DIMMER SWITCH
<br />VACANCY SENSORS
<br />S
<br />S
<br />D
<br />vs
<br />110 VOLT WEATHER PROOF OUTLET, GFIGFI/
<br />WP
<br />SD
<br />3-WAY SWITCHS3
<br />CARBON MONOXIDE DETECTORS
<br />(CRC R315) SECTIONS R315.1 & R315.2
<br />CO
<br />1. ALL EXISTING APPROVED SMOKE ALARMS & CARBON
<br />MONOXIDE ALARM IN EACH UNITS. IF NOT PLEASE PROVIDE
<br />& SHALL COMPLY WITH THE STATE ENERGY STANDARDS &
<br />CITY MUNICIPAL CODE STANDARDS.
<br />(FIELD VERIFY AT LOCATION)
<br />2.ALL RECEPTACLE OUTLETS SHALL BE LISTED
<br />TAMPER-RESISTANT RECEPTACLE PER CEC 406.12
<br />3.BATHROOM RECEPTACLES SHALL BE SERVED BY A
<br />DEDICATED 20 AMP CIRCUIT PER CEC 210.52(D)
<br />NOTES:
<br />LEGEND
<br />EXISTING WALL
<br />NEW WALL
<br />FOR ALTERATIONS, REPAIRS OR ADDITIONS EXCEEDING $1000,
<br />EXISTING DWELLINGS OR SLEEPING UNITS THAT HAVE
<br />ATTACHED GARAGES OR FUEL-BURNING APPLIANCES SHALL
<br />BE PROVIDED WITH A CARBON MONOXIDE ALARM. (R315.1 CRC).
<br />* ALARMS WILL BE BATTERY OPERATED.
<br />* ALARMS SHALL BE LOCATED OUTSIDE EACH SEPARATE
<br />SLEEPING AREA IN THE IMMEDIATE VICINITY OF THE
<br />BEDROOMS.
<br />*LISTING & APPROVAL BY THE OFFICE OF THE STATE FIRE
<br />MARSHAL FOR COMBINED CARBON MONOXIDE & SMOKE
<br />ALARMS ARE ALLOWED.
<br />1. WALLS 2 FT. OR GREATER SHALL HAVE AN OUTLET. OUTLETS
<br />SHALL BE SPACED MAX. 12 FT. APART, AND A MAXIMUM OF 6 FT.
<br />FROM END OF WALLS OR OPENING (CEC 210-52A)
<br />2. ALL RECEPTACLE OUTLETS SHALL BE LISTED
<br />TAMPER-RESISTAND RECEPTACLE PER CEC 406.11.
<br />3. BATHROOM RECEPTACLES SHALL BE SERVED BY A DEDICATED
<br />20 AMP CIRCUIT PER CEC 210-52(D).
<br />ALL NEW CONSTRUCTION, INTERIOR OR EXTERIOR
<br />ALL NEW CONSTRUCTION, INTERIOR OR EXTERIOR
<br />ALTERATIONS, REPAIRS, OR ADDITIONS REQUIRING A PERMIT
<br />AND HAVING A VALUATION IN EXCESS OF $1,000, AN APPROVED
<br />CARBON MONOXIDE ALARM SHALL BE INSTALLED IN DWELLING
<br />UNITS AND IN SLEEPING UNITS WITHIN WHICH FUEL-BURNING
<br />APPLIANCES ARE INSTALLED AND IN DWELLING UNITS THAT
<br />HAVE ATTACHED GARAGES SHALL BE PROVIDED WITH CARBON
<br />MONOXIDE ALARMS (CRCR315)
<br />- CARBON MONOXIDE ALARMS SHALL ONLY BE REQUIRED IN
<br />THE SPECIFIC DWELLING UNIT OR SLEEPING UNIT FOR
<br />WHICH THE PERMIT WAS OBTAINED. CARBON MONOXIDE
<br />ALARMS REQUIRED BY SECTIONS R315.1 AND R315.2 SHALL
<br />BE INSTALLED. REVISE DRAWINGS TO SHOW COMPLIANCE.
<br />- OUTSIDE OF EACH SEPARATE DWELLING UNIT SLEEPING
<br />AREA IN THE IMMEDIATE VICINITY OF THE BEDROOM(S).
<br />- ON EVERY LEVEL OF A DWELLING UNIT INCLUDING
<br />BASEMENTS.
<br />- WHERE MORE THAN ONE CARBON MONOXIDE ALARM IS
<br />REQUIRED TO BE INSTALLED WITHIN THE DWELLING UNIT
<br />OR WITHIN A SLEEPING UNIT THE ALARM SHALL BE
<br />INTERCONNECTED IN A MANNER THAT ACTIVATION OF ONE
<br />ALARM SHALL ACTIVATE ALL OF THE ALARMS IN THE
<br />INDIVIDUAL UNIT.
<br />EXCEPTION:
<br />INTERCONNECTION IS NOT REQUIRED IN EXISTING DWELLING
<br />UNITS WHERE REPAIRS DO NOT RESULT IN THE REMOVAL OF
<br />WALL AND CEILING FINISHED, THERE IS NO ACCESS BY MEANS
<br />OF ATTIC, BASEMENT OR CRAWL SPACE, AND NO PREVIOUS
<br />METHOD FOR INTERCONNECTION EXISTED.
<br />1. PROVIDE A MINIMUM OF 2-20 AMP SMALL APPLIANCE
<br />CIRCUITS FOR THE KITCHEN COUNTER TOPS. SUCH
<br />CIRCUIT SHALL HAVE NO OTHER OUTLETS. LOADS SHALL BE
<br />BALANCED. CEC 210-52(B)(2).
<br />2. PROVIDE A MINIMUM OF 1-20 AMP LAUNDRY BRANCH
<br />CIRCUIT. SUCH CIRCUIT SHALL HAVE NO OTHER OUTLETS.
<br />CEC 210-23(a)
<br />3.ALL INSTALLED LUMINAIRES MUST BE HIGH EFFICACY IN
<br />ACCORDANCE WITH TABLE 150.0A.
<br />4.EXHAUST FANS MUST BE SWITCHED SEPARATELY FROM
<br />LIGHTING SYSTEMS.
<br />5.IN BATHROOMS, GARAGES, LAUNDRY ROOMS, AND UTILITY
<br />ROOMS, AT LEAST ONE LUMINAIRE IN EACH OF THESE
<br />SPACES MUST BE CONTROLLED BY A VACANCY SENSOR.
<br />1.KITCHEN RANGE HOOD (NEW CONSTRUCTION CA ENERGY
<br />CODE 150.0(o)2.B.) SHALL BE FIELD VERIFIED IN
<br />ACCORDANCE WITH THE PROCEDURES IN REFERENCE
<br />RESIDENTIAL APPENDIX RA3.7.4.3 TO CONFIRM TO THE
<br />MODEL IS RATED BY HVI TO COMPLY WITH THE FOLLOWING
<br />REQUIREMENTS:
<br />A.THE MINIMUM VENTILATION RATE AS SPECIFIED IN
<br />SECTION 5 OF ASHRAE 62.2.
<br />B.THE MAXIMUM SOUND RATING AS SPECIFIED IN
<br />SECTION 7,2 OF ASHRAE 62.2.
<br />2.DUCTS USED FOR DOMESTIC KITCHEN RANGE OR
<br />COOKTOP VENTILATION SHALL BE OF METAL AND SHALL
<br />HAVE SMOOTH INTERIOR SURFACES. (504.3)
<br />EXCEPTION: DUCTS FOR DOMESTIC KITCHEN DOWNDRAFT
<br />GRILL-RANGE VENTILATION INSTALLED UNDER A CONCRETE
<br />SLAB FLOOR SHALL BE PERMITTED TO BE OF APPROVED
<br />SCHEDULE 40 PVC PROVIDED IN COMPLIANCE WITH CMC
<br />504.3.
<br />3.CONDENSATE WASTE SHALL BE COLLECTED AND
<br />DISCHARGED TO AN APPROVED PLUMBING FIXTURE OR
<br />DISPOSAL AREA. CONDENSATE OR WASTEWATER SHALL
<br />NO DRAIN OVER A PUBLIC WAY. (310.1)
<br />*MECHANICAL UNIT FILTERS MUST BE MERV-13 OR BETTER.
<br />(150.0(m)12C)
<br />NOTES:
<br />MECH. NOTES:
<br />ADDITIONAL ELECTRICAL NOTES:
<br />NEW CONSTRUCTION (150.0(N). WATER HEATING SYSTEMS USING GAS OR
<br />PROPANE TO SERVE INDIVIDUAL DWELLING UNITS SHALL DESIGNATE A
<br />SPACE AT LEAST 2.5 FEET BY 2.5 FEET WIDE AND 7 FEET TALL SUITABLE FOR
<br />THE FUTURE INSTALLATION OF A HEAT PUMP WATER HEATER (HPWH) BY
<br />MEETING EITHER A OR B BELOW.
<br />A.A DEDICATED 125 VOLTS, 20-AMP ELECTRICAL RECEPTACLE THAT IS
<br />CONNECTED TO THE ELECTRIC PANEL WITH A 120/240 VOLT 3 CONDUCTOR,
<br />10 AWG COPPER BRANCH CIRCUIT, WITHIN 3 FEET FROM THE WATER
<br />HEATER AND ACCESSIBLE TO THE WATER HEATER WITH NO
<br />OBSTRUCTIONS; AND
<br />B.BOTH ENDS OF THE UNUSED CONDUCTOR SHALL BE LABELED WITH THE
<br />WORD “SPARE” AND BE ELECTRICALLY ISOLATED; AND
<br />C.A RESERVED SINGLE POLE CIRCUIT BREAKER SPACE IN THE ELECTRICAL
<br />PANEL ADJACENT TO THE CIRCUIT BREAKER FOR THE BRANCH CIRCUIT
<br />ABOVE AND LABEL WITH THE WORDS “FUTURE 240V USE”; AND
<br />D.A CONDENSATE DRAIN THAT IS NO MORE THAN 2 INCHES HIGHER THAN
<br />THE BASE OF THE INSTALLED WATER HEATER, AND ALLOWS NATURAL
<br />DRAINING WITHOUT PUMP ASSISTANCE.
<br />ENERGY STORAGE SYSTEM (ESS) READY. AT LEAST ONE OF THE
<br />FOLLOWING SHALL BE PROVIDED:
<br />A.ESS READY INTERCONNECTION EQUIPMENT WITH A MINIMUM BACKED-UP
<br />CAPACITY OF 60 AMPS AND A MINIMUM OF FOUR ESS-SUPPLIED BRANCH
<br />CIRCUITS, OR
<br />B.A DEDICATED RACEWAY FROM THE MAIN SERVICE PANEL TO A
<br />PANELBOARD (SUBPANEL) THAT SUPPLIES THE FOLLOWING BRANCH
<br />CIRCUITS: REFRIGERATOR, LIGHTING CIRCUIT NEAR PRIMARY EGRESS
<br />DOOR, SLEEPING ROOM RECEPTACLE AND ONE ADDITIONAL.
<br />THE MAIN PANELBOARD SHALL HAVE A MINIMUM BUSBAR RATING OF 225
<br />AMPS. SPACE SHALL BE RESERVED TO ALLOW FUTURE INSTALLATION OF A
<br />SYSTEM ISOLATION EQUIPMENT/TRANSFER SWITCH WITHIN 3 FEET OF THE
<br />MAIN PANELBOARD. RACEWAYS SHALL BE INSTALLED BETWEEN THE
<br />PANELBOARD AND THE SYSTEM ISOLATION EQUIPMENT TO ALLOW THE
<br />CONNECTION OF BACKUP POWER SOURCE.
<br />HEAT PUMP SPACE HEATER READY. SYSTEMS USING A GAS OR PROPANE
<br />FURNACE SHALL INCLUDE A DEDICATED 240-VOLT BRANCH CIRCUIT WITH 3
<br />FEET OF THE FURNACE. THE BRANCH CIRCUIT SHALL BE RATED AT 30 AMPS
<br />MINIMUM. THE MAIN ELECTRICAL SERVICE SHALL HAVE A RESERVED SPACE
<br />TO ALLOW FOR THE INSTALLATION OF A DOUBLE POLE CIRCUIT BREAKER.
<br />THE RESERVED SPACE SHALL BE PERMANENTLY MARKED AS “FOR FUTURE
<br />240V USE”. (CALIFORNIA ENERGY CODE 150.0(T))
<br />ELECTRIC COOKTOP READY. SYSTEMS USING A GAS OR PROPANE
<br />COOKTOP SHALL INCLUDE A DEDICATED 240-VOLT BRANCH CIRCUIT WITH 3
<br />FEET OF THE COOKTOP. THE BRANCH CIRCUIT SHALL BE RATED AT 50 AMPS
<br />MINIMUM. THE MAIN ELECTRICAL SERVICE SHALL HAVE A RESERVED SPACE
<br />TO ALLOW FOR THE INSTALLATION OF A DOUBLE POLE CIRCUIT BREAKER.
<br />THE RESERVED SPACE SHALL BE PERMANENTLY MARKED AS “FOR FUTURE
<br />240V USE”. (CALIFORNIA ENERGY CODE 150.0(U))
<br />ELECTRICAL CLOTHES DRYER READY. SYSTEMS USING A GAS OR PROPANE
<br />DRYER SHALL INCLUDE A DEDICATED 240-VOLT BRANCH CIRCUIT WITH 3
<br />FEET OF THE CLOTHES DRYER. THE BRANCH CIRCUIT SHALL BE RATED AT
<br />30 AMPS MINIMUM. THE MAIN ELECTRICAL SERVICE SHALL HAVE A
<br />RESERVED SPACE TO ALLOW FOR THE INSTALLATION OF A DOUBLE POLE
<br />CIRCUIT BREAKER. THE RESERVED SPACE SHALL BE PERMANENTLY
<br />MARKED AS “FOR FUTURE 240V USE”. (CALIFORNIA ENERGY CODE 150.0(V))
<br />1. AT BEDROOMS PROVIDE ONE OPENABLE ESCAPE
<br />WINDOW OR DOOR MEETING ALL OF THE FOLLOWING:
<br />A. AN OPENABLE AREA OF NOT LESS THAN 5.7 SQ.
<br />FT. (5.0 SF. AT GRADE LEVEL)
<br />B. A MINIMUM CLEAR 24 INCH HEIGHT AND 20 INCH
<br />WIDTH
<br />C. CLEAR OPENING NOT OVER 44 INCHES ABOVE THE
<br />FLOOR. CBC 1026.2
<br />2. SHOWERS SHALL BE FINISHED 72" ABOVE DRAIN WITH
<br />MATERIALS NOT ADVERSELY AFFECTED BY MOISTURE.
<br />3. ANTI-SCALDING SHOWER AND TUB-SHOWER VALVES
<br />REQUIRED.
<br />4.ADDITIONS THAT EXCEED 50% OF EXISTING LIVING
<br />FLOOR AREA REQUIRE UNDER GROUNDING OF ALL
<br />EXISTING ABOVE GROUND UTILITIES. "PER BUILDING
<br />POLICY, WHERE FEASIBLE, AND AS DETERMINED BY
<br />THE BUILDING INSPECTOR, ALL ABOVE-GROUND
<br />UTILITIES SHALL BE RELOCATED UNDERGROUND."
<br />5.ALL NEW WINDOWS INCLUDING:
<br />U-FACTORS = 0.30 & SHGC = 0.23
<br />NOTES:
<br />22X30
<br />ATTIC
<br />HB
<br />(N)FAU 17
<br />D1
<br />16
<br />D1
<br />AFCI
<br />(N) SD
<br />WHOLE
<br />HOUSE FAN
<br />50 CFM
<br />ALL SERVICES SUPPYING DWELLING UNITS SHALL
<br />BE PROVIDED A SURGE PROTECTION DEVICE. THE
<br />SPD SHALL BE AN INTEGRAL PART OF THE
<br />SERVICE EQUIPMENT OR SHALL BE LOCATED
<br />IMMEDIATELY ADJACENT THERETO. (CEC 230.667)
<br />PAD SUPPORTING CONDENSER
<br />SHALL BE A MINIMUM OF 3"
<br />ABOVE THE GRADE.
<br />HOOD OVER ELECTRIC
<br />RANGE SHALL BE
<br />160CFM OR 65% CE FOR
<br />ELECTRICAL RANGE
<br />(MAX 3 SONES)
<br />PROVIDED UFER OR OTHER
<br />APPROVED GROUND PER CEC 250.
<br />NOTE:
<br />THE MAIN PANELBOARD SHALL HAVE A
<br />MINIMUM BUSBAR RATING OF 225.
<br />RHEEM-HEAT PUMP
<br />40 GAL
<br />ELEC. HEAT PUMP
<br />PROVIDE BLOCKING FOR
<br />FUTURE ADA GRAB BAR
<br />ELECTRICAL PLAN
<br />SCALE: 1/4" = 1'-0"
<br />12'-9"
<br />27
<br />'
<br />-
<br />1
<br />"
<br />25'-0"
<br />10
<br />'
<br />-
<br />0
<br />"
<br />W/D WH
<br />PANTRY
<br />DW
<br />16
<br />'
<br />-
<br />4
<br />"
<br />9'
<br />-
<br />6
<br />"
<br />5'
<br />-
<br />6
<br />"
<br />13'-0"2'-1"8'-3"
<br />21'
<br />-
<br />0
<br />"
<br />(N) ADU
<br />ELEC
<br />PANEL
<br />200 AMP
<br />COND.
<br />(N) KITCHEN
<br />(N) 9'-0" CL. HT.
<br />(N) BEDROOM #1
<br />(N) 9'-0" CL. HT.
<br />(N) LIVING ROOM
<br />(N) 9'-0" CL. HT.
<br />(N) BATH
<br />(N) 9'-0" CL. HT.
<br />(N) 2'0"X2'0" SLD
<br />OBS TEMP WD
<br />(N) 4'0"X4'0" SLD WD
<br />(N) 5'0"X4'0" SLD TEMP. WD
<br />(N
<br />)
<br />
<br />4
<br />'
<br />0
<br />"
<br />X
<br />4
<br />'
<br />0
<br />"
<br />
<br />S
<br />L
<br />D
<br />
<br />W
<br />D
<br />(N
<br />)
<br />
<br />3
<br />'
<br />0
<br />"
<br />X
<br />3
<br />'
<br />0
<br />"
<br />
<br />S
<br />L
<br />D
<br />
<br />W
<br />D
<br />(N
<br />)
<br />
<br />3
<br />'
<br />0
<br />"
<br />X
<br />6
<br />'
<br />8
<br />"
<br />
<br />E
<br />N
<br />T
<br />R
<br />Y
<br />
<br />D
<br />R
<br />.
<br />(N) 2'6"X6'8"
<br />LOUVER DR.
<br />(N) PORCH
<br />(N) 9'-0" CL. HT.
<br />3'
<br />-
<br />0
<br />"
<br />10'-6"
<br />ESS READY
<br />SEE DIAGRAM
<br />AFCI
<br />AFCIAFCI
<br />AFCI
<br />AFCI
<br />AFCI
<br />AFCIAFCI
<br />S
<br />GFCI
<br />SS
<br />VS
<br />GFCI
<br />TYPE 1 CLOTHES DRYER EXHAUST DUCT
<br />(MIN. 4 INCH DIA. AND 0.16" THICK RIGID
<br />METAL TO OUTSIDE OF THE BUILDING
<br />AND EQUIPPED WITH A BACK-DRAFT
<br />DAMPER. EXHAUST DUCT LENGTH IS
<br />LIMITED TO 14 FT. WITH 2 ELBOWS.
<br />(N) SD+CO
<br />PHOTOELEC.
<br />HB
<br />AFCI
<br />GFCI
<br />AFCI
<br />GFCI
<br />AFCI
<br />GFCI
<br />AFCI
<br />GFCI
<br />AFCI
<br />GFCI
<br />AFCI
<br />GFCI
<br />AFCI
<br />(N) LED
<br />PHOTO
<br />CONTROL &
<br />MOTION
<br />SENSOR
<br />(N) LED
<br />PHOTO
<br />CONTROL &
<br />MOTION
<br />SENSOR
<br />D
<br />S
<br />SS
<br />SS
<br />S
<br />S
<br />DD
<br />3 3
<br />AFCI
<br />S
<br />(N) LED
<br />PHOTO
<br />CONTROL &
<br />MOTION
<br />SENSOR
<br />(N) LED
<br />PHOTO
<br />CONTROL &
<br />MOTION
<br />SENSOR
<br />(N) LED
<br />PHOTO
<br />CONTROL &
<br />MOTION
<br />SENSOR
<br />(N) LED
<br />PHOTO
<br />CONTROL &
<br />MOTION
<br />SENSOR
<br />PROVIDE NOTE: "EFFECTIVE JANUARY 1, 2014, SENATE
<br />BILL 407 REQUIRES A BUILDING PERMIT APPLICANT TO
<br />REPLACE ALL NONCOMPLIANT PLUMBING FIXTURES IN
<br />PROPERTIES BUILT AND AVAILABLE FOR USE ON OR
<br />BEFORE JANUARY 1, 1994 WITH WATER-CONSERVING
<br />PLUMBING FIXTURES AS A CONDITION FOR APPROVAL
<br />OF A FINAL BUILDING PERMIT FOR BUILDING
<br />ALTERATIONS OR IMPROVEMENTS. CONTRACTOR
<br />SHALL COMPLETE SB 407 AFFIDAVIT FORM AND
<br />SUBMIT TO THE INSPECTOR PRIOR TO FINAL
<br />INSPECTION. NON COMPLIANT PLUMBING FIXTURES
<br />MEANS ANY OF THE FOLLOWIN
<br />1.ANY TOILET MANUFACTURED TO USE MORE
<br />THAN 1.28 GALLONS OF WATER PER FLUSH
<br />2.ANY URINAL MANUFACTURED TO USE MORE
<br />THAN ONE GALLON OF WATER PER FLUSH
<br />3. ANY SHOWERHEAD MANUFACTURED TO HAVE A
<br />FLOW CAPACITY OF MORE THAN 1.8 GPM
<br />4.ANY INTERIOR FAUCET THAT EMITS MORE THAN
<br />2.0 GPM.
<br />1.THE WHOLE-BUILDING VENTILATION EXHAUST FAN WILL OPERATE
<br />CONTINUOUSLY AND IS REQUIRED TO BE RATED FOR SOUND AT A
<br />MAXIMUM OF 1 SONE. THIS EXHAUST FAN CAN BE CONTROLLED BY
<br />A STANDARD ON/OFF SWITCH BUT THE SWITCH MUST BE LABELED
<br />CLEARLY DISPLAYING THE FOLLOWING TEXT, OR EQUIVALENT. "THIS
<br />SWITCH CONTROLS THE INDOOR AIR QUALITY VENTILATION FOR
<br />THE HOUSE. LEAVE SWITCH IN THE "ON" POSITION AT ALL TIMES
<br />UNLESS THE OUTDOORAIR QUALITY IS VERY POOR." [150.0(o)J]
<br />WHOLE HOUSE FAN INFO:
<br />MANUF. = PANASONIC
<br />MODEL # = RG-R811LA
<br />1 SONE RATING
<br />WHOLE HOUSE FAN NOTES:
<br />AGING-IN-PLACE/FALL PREVENTION NOTES:
<br />A.REINFORCEMENT FOR GRAB BARS. [R327.1.1]
<br />AT LEAST ONE BATHROOM ON THE ENTRY LEVEL SHALL BE
<br />PROVIDED WITH REINFORCEMENT INSTALLED IN ACCORDANCE
<br />WITH THIS SECTION. WHERE THERE IS NO BATHROOM ON THE
<br />ENTRY LEVEL, AT LEAST ONE BATHROOM ON THE 2ND OR 3RD
<br />FLOOR OF THE DWELLING SHALL COMPLY WITH THIS SECTION.
<br />1.REINFORCEMENT SHALL BE SOLID LUMBER OR OTHER
<br />CONSTRUCTION MATERIALS APPROVED BY THE ENFORCING
<br />AGENCY.
<br />2.REINFORCEMENT SHALL NOT BE LESS THAN 2 BY 8 INCH NOMINAL
<br />LUMBER (1-1/2” X 7-1/4” ACTUAL DIMENSION) OR OTHER
<br />CONSTRUCTION MATERIAL PROVIDING EQUAL HEIGHT AND LOAD
<br />CAPACITY. REINFORCEMENT SHALL BE LOCATED BETWEEN 32” AND
<br />39-1/4” ABOVE THE FINISHED FLOOR, FLUSH WITH THE WALL
<br />FRAMING.
<br />3.WATER CLOSET REINFORCEMENT SHALL BE INSTALLED ON BOTH
<br />SIDE WALLS OF THE FIXTURE, OR ONE SIDE WALL AND THE BACK
<br />WALL.
<br />4.SHOWER REINFORCEMENT SHALL BE CONTINUOUS WHERE WALL
<br />FRAMING IS PROVIDED.
<br />5.BATHTUB AND COMBINATION BATHTUB/SHOWER
<br />REINFORCEMENT SHALL BE CONTINUOUS ON EACH END OF THE
<br />BATHTUB AND THE BACK WALL. ADDITIONALLY, BACK WALL
<br />REINFORCEMENT FOR A LOWER GRAB BAR SHALL BE PROVIDED
<br />WITH THE BOTTOM EDGE LOCATED NO MORE THAN 6” ABOVE THE
<br />BATHTUB RIM.
<br />6.WHERE THE WATER CLOSET IS NOT PLACED ADJACENT TO A SIDE
<br />WALL CAPABLE OF ACCOMMODATING A GRAB BAR, THE BATHROOM
<br />SHALL HAVE PROVISIONS FOR INSTALLATION OF FLOOR-MOUNTED,
<br />FOLDAWAY OR SIMILAR ALTERNATE GRAB BAR REINFORCEMENTS
<br />APPROVED BY THE ENFORCING AGENCY.
<br />B.DOCUMENTATION FOR GRAB BAR REINFORCEMENT. [R327.1.1.1]
<br />INFORMATION AND/OR DRAWINGS IDENTIFYING THE LOCATION OF
<br />GRAB BAR REINFORCEMENT SHALL BE PLACED IN THE OPERATION &
<br />MAINTENANCE MANUAL IN ACCORDANCE WITH THE CALIFORNIA
<br />GREEN BUILDING STANDARDS CODE, CH. 4, DIVISION 4.4.
<br />C.DOORBELL BUTTONS. [R327.1.4]
<br />DOORBELL BUTTONS OR CONTROLS, WHEN INSTALLED, SHALL NOT
<br />EXCEED 48” ABOVE EXTERIOR FLOOR OR LANDING, MEASURED
<br />FROM THE TOP OF THE DOORBELL BUTTON ASSEMBLY. WHERE
<br />DOORBELL BUTTONS INTEGRATED WITH OTHER FEATURES ARE
<br />REQUIRED TO BE INSTALLED ABOVE 48” MEASURED FROM THE
<br />EXTERIOR FLOOR OR LANDING, A STANDARD DOORBELL BUTTON OR
<br />CONTROL SHALL ALSO BE PROVIDED AT A HEIGHT NOT EXCEEDING
<br />48” ABOVE EXTERIOR FLOOR OR LANDING, MEASURED FROM THE
<br />TOP OF THE DOORBELL BUTTON OR CONTROL.
<br />ALL BRANCH CIRCUITS THAT SUPPLY 125 VOLT, SINGLE
<br />PHASE, 15 AND 20 AMPERE OUTLETS INSTALLED IN
<br />DWELLING UNITS SHALL BE PROTECTED BY AN ARC-FAULT
<br />CIRCUIT INTERRUPTER(S). [CEC 210.12] NOTE THIS
<br />REQUIREMENT IS FOR ENTIRE CIRCUIT, NOT JUST THE OUTLETS.
<br />NOTES:
<br />1)PROVIDE SMOKE ALARM IN EACH BEDROOM OR
<br />SLEEPING AREA, AND OUTSIDE OF EACH SEPARATE
<br />BEDROOM/SLEEPING AREA IN THE IMMEDIATE VICINITY OF THE
<br />BEDROOM/SLEEPING AREA. LOCATION OF SMOKE DETECTORS
<br />SHALL COMPLY WITH CRC SECTION R314.3.3. HARDWIRED AND
<br />INTERCONNECTED SMOKE ALARMS ARE REQUIRED. (CRC R314)
<br />2)PROVIDE CARBON MONOXIDE ALARM OUTSIDE OF EACH
<br />SEPARATE BEDROOM/SLEEPING AREA IN THE IMMEDIATE
<br />VICINITY OF THE BEDROOM/SLEEPING AREA. HARDWIRED AND
<br />INTERCONNECTED CARBON MONOXIDE ALARMS Are Required.
<br />(CRC R315)
<br />3)SMOKE ALARMS SHALL BE AT LEAST 3 ' FROM A SUPPLY
<br />REGISTER OR A BATHROOM DOOR/OPENING.
<br />4)SMOKE ALARMS SHALL BE AT LEAST 20 ' FROM COOKING
<br />APPLIANCE (10' FOR IONIZATION ALARM WITH SILENCING
<br />SWITCH OR PHOTOELECTRIC ALARM).
<br />NOTES:ELECTRICAL RECEPTACLE OUTLETS, SWITCHES AND CONTROLS
<br />SHALL BE LOCATED NO MORE THAN 48” MEASURED TO TOP OF
<br />THE OUTLET BOX AND NOT LESS THAN 15” MEASURED FROM
<br />BOTTOM OF THE OUTLET BOX ABOVE THE FINISH FLOOR.
<br />NOTES:
<br />SCALE:
<br />DRAWN BY:
<br />DATE:
<br />PLAN CHECK
<br />DRAWING TITLE:
<br />DATEREVISIONS:
<br />HN
<br />12-11-2024
<br />AS NOTED
<br />00-00-0000
<br />SHEET NO. OF SHEETS
<br />DATE
<br />00-00-2024--------
<br />00-00-0000
<br />00-00-0000
<br />00-00-0000
<br />00-00-0000
<br />CONSULTANT:
<br />21
<br />0
<br />
<br />W
<br />.
<br />
<br />H
<br />A
<br />R
<br />V
<br />E
<br />Y
<br />
<br />A
<br />V
<br />E
<br />.
<br />
<br />U
<br />N
<br />I
<br />T
<br />
<br />#
<br />2
<br />(
<br />A
<br />D
<br />U
<br />)
<br />,
<br />SA
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />7
<br />RESIDENTIAL PROJECT FOR:
<br />210 W. HARVEY AVE.(ADU),
<br />SANTA ANA, CA 92707
<br />DE
<br />T
<br />A
<br />C
<br />H
<br />E
<br />D
<br />
<br />A
<br />D
<br />U
<br />
<br />P
<br />R
<br />O
<br />J
<br />E
<br />C
<br />T
<br />Exp. date:
<br />STATE OF CALIFORNIACIVIL
<br />REGISTERED PROFESS IONAL ENGINEER
<br />HUE C . LUI
<br />C-66754
<br />9/26
<br />1/29/2025
<br />HA NGUYEN - 1/29/2025
<br />ELECTRICAL
<br />PLAN
<br />06 11
<br />A2
<br />210 W Harvey Ave
<br />Unit #24/22/2025
|