|
INDEX
<br />A1
<br />A2 SITE PLAN
<br />S102'8/($1'%$//$67/$<287
<br />E 1a SINGLE LINE DIAGRAM
<br />E2 PLACARD
<br />E3 LABELS
<br />SOLAR PROPERTY PLAN
<br />PROJECT INFORMATION
<br /> ALL WORK SHALL COMPLY WITH THE:
<br /> 2022 CALIFORNIA BUILDING CODE (CBC)
<br /> 2022 CALIFORNIA RESIDENTIAL CODE (CRC)
<br /> 2022 CALIFORNIA FIRE CODE (CFC)
<br /> 2022 CALIFORNIA ELECTRICAL CODE (CEC)
<br /> 2022 CALIFORNIA MECHANICAL CODE (CMC)
<br /> 2022 CALIFORNIA PLUMBING CODE (CPC)
<br /> 2022 CALIFORNIA ENERGY CODE (CEnC)
<br /> 2022 CALIFORNIA GREEN BUILDING STANDARDS CODE (CGBSC)
<br /> 2023 COUNTY OF LOS ANGELES FIRE CODE
<br /> ALL OTHER ORDINANCES ADOPTED BY THE LOCAL GOVERNING AGENCIES
<br />SCOPE OF WORK
<br />VICINITY MAP
<br />AERIAL MAP
<br />1. 1.ALL WORK SHALL BE IN ACCORDANCE WITH THE LATEST EDITION OF THE NEC (NATIONAL ELECTRIC CODE), NFPA
<br />(NATIONAL FIRE PROTECTION ASSOCIATION), AND ALL APPLICABLE LOCAL, STATE, AND FEDERAL CODES, LAWS AND REGULATIONS.
<br />2. 2.ALL WORK SHALL CONFIRM TO APPLICABLE STATE AND FEDERAL SAFETY CODES INCLUDING OSHA AND CAL OSHA. NO "HOT" WORK IS AUTHORIZED. ALL "HOT"
<br />WORK SHALL BE APPROVED IN WRITING WITH THE GENERAL CONTRACTOR AND OWNER.
<br />3. COORDINATE ALL WORK WITH ARCHITECTURAL, MECHANICAL AND STRUCTURAL DRAWINGS, INSTALL ALL WORK TO CLEAR NEW AND EXISTING ARCHITECTURAL AND
<br />STRUTURAL MEMBERS. NO ITEM SUCH AS A PIPE, DUCT, ETC. SHALL BE IN CONTACT WITH ANY ELECTRICAL EQUIPMENT.
<br />4. CONTRACTOR SHALL ASSUME SOLE AND COMPLETE RESPONSIBILITY FOR JOB SITE CONDITIONS DURING THE COURSE OF CONSTRUCTION OF THIS PROJECT,
<br />INCLUDING SAFETY OF ALL PERSONS AND PROPERTY AND SECURITY OF THE WORKSITE. THIS REQUIREMENT SHALL APPLY CONTINUOUSLY AND NOT BE LIMITED TO
<br />NORMAL WORKING HOURS.
<br />5. NOTIFY THE PRIME CONTRACTOR OR OWNER IMMEDIATELY AFTER DISCOVERING ANY HAZARDOUS MATERIAL.
<br />6. DRAWINGS ARE DIAGRAMMATIC AND INDICATE GENERAL ARRANGEMENT OF SYSTEMS AND WORK INCLUDED. VERIFY THE EXACT LOCATIONS AND CONDITIONS OF
<br />ALL EQUIPMENT REQUIRING ELECTRICAL CONNECTIONS PRIOR TO ANY WORK. LOCATIONS FOR EQUIPMENT SHALL BE TAKEN FROM THE OTHER SHEETS WHERE THEY
<br />OCCUR. EXTEND WIRING FROM ALL JUNCTION BOXES, CONTROL PANELS, PUMPS, RECEPTACLES, SWITCHES, ETC. AND MAKE ALL FINAL CONNECTIONS TO THE
<br />EQUIPMENT AS REQUIRED.
<br />7. THE INTENT OF THESE DRAWINGS IS FOR A COMPLETE ELECTRICAL SYSTEM. ANY ERRORS OR UNCERTAINTY SHALL BE BROUGHT TO THE ATTENTION OF THE PRIME
<br />CONTRACTOR AND ENGINEER AS SOON AS FOUND.
<br />8. THE COMPLETE ELECTRICAL INSTALLATION SHALL BE TESTED AS A COMPLETE WORKING SYSTEM.
<br />9. RESTORE ALL DAMAGES RESULTING FROM WORK AND LEAVE PREMISES IN CLEAN CONDITION WHEN FINISHED WITH
<br />10.FIRE STOP ALL PENETRATIONS THROUGH FIRE RATED SURFACES.
<br />11.ALL NEW CIRCUIT BREAKERS SHALL BE RATED 10,000 AIC OR HIGHER
<br />12.ALL CONDUITS SHALL BE EMT, INTERMEDIATE METAL CONDUIT, OR RIGID STEEL. MINIMUM SIZE SHALL BE 1/2". ALL CONDUIT, BOXES, AND ELECTRICAL FITTINGS SHALL BE
<br />STEEL.
<br />13.DO NOT USE THE WORKING SPACE WITHIN ANY EXIT SIGN OR ASSOCIATED JUNCTION BOX FOR ANY OTHER CIRCUIT.
<br />14.PROVIDE EXPANSION AND DEFLECTION FITTINGS IN CONDUITS CROSSING BUILDING EXPANSION AND SEISMIC JOINTS.
<br />15.PROVIDE JUNCTION AND/OR PULL BOXES WHEN NECESSARY OR REQUIRED BY NEC.
<br />16.ALL CONDUCTORS SHALL BE COPPER, THHN, #12 AWG MINIMUM. UNLESS IN A WET LOCATION IN WHICH CASE THEN SHALL BE USED.
<br />17.INSTALL GREEN INSULATED GROUND WIRE IN ALL CIRCUITS. SIZE PER NEC REQUIREMENTS OR THE SAME AS PHASE CONDUCTORS, WHICHEVER IS LARGER. UNLESS
<br />INDICATED OTHERWISE.
<br />18.ALL NEW WIRING, CONDUIT, AND JUNCTION BOXES SHALL BE CONCEALED WITHIN NEW WALLS, CEILINGS OR FLOOR SPACES. SURFACE MOUNT CONDUIT ON OLD
<br />WALLS AND CEILINGS. RUN ALL SURFACE RACEWAY TIGHT TO THE STRUCTURE, PARALLEL TO BUILDING LINES.
<br />19.NO FOREIGN EQUIPMENT SHALL BE LOCATED WITHIN THE SPACE ABOVE OR BELOW THE ELECTRIC PANELS.
<br />20.PROVIDE SIGNAGE ON ALL ELECTRIC PANELS TO KEEP THE SPACE 36" IN FRONT OF THE PANELS FREE OF OBSTRUCTIONS.
<br />21.PROVIDE WARNING LABEL ON ALL PANELS "WARNING, ELECTRICAL ARC FLASH HAZARD, PERSONAL PROTECTION EQUIPMENT REQUIRED, FAILURE TO COMPLY CAN
<br />RESULY IN INJURY OR DEATH, REFER TO NFPA 70E." WHERE THE TERMINAL OF THE DISCONNECTING MEANS MAY BE ENERGIZED IN THE OPEN POSITION, A WARNING
<br />SIGN SHALL BE MOUNTED ON OR ADJACENT TO THE DISCONNECTING MEANS. THE SIGN SHALL BE CLEARLY LEGIBLE AND HAVE THE FOLLOWING WORDS OR
<br />EQUIVALENT: "WARNING - ELECTRIC SHOCK HAZARD, DO NOT TOUCH TERMINALS. TERMINALS ON BOTH THE LINE AND THE LOAD SIDES MAY BE ENERGIZED IN THE OPEN
<br />POSITION."
<br />22.UPDATE PANEL BOARD DIRECTORY AS CIRCUITS ARE INSTALLED. PREPARE NEW TYPE WRITTEN PANEL SCHEDULES.
<br />23.ALL EXTERIOR EQUIPMENT SHALL BE IN WEATHERPROOF (NEMA 3R) ENCLOSURES. ALL NEW WIRING SHALL BE IN CONDUIT, SUITABLE FOR SUN EXPOSURE AND WET
<br />LOCATIONS. FIELD APPLIED COATINGS ARE NOT ACCEPTABLE.
<br />24.DC SOLAR POWER SHALL BE NEGATIVELY GROUNDED.
<br />25.ALL MARKING SHALL BE PER CODE REQUIREMENTS.
<br />26.INVERTERS MUST COMPLY WITH UL 1741 TO PREVENT ISLANDING ON POWER FAILURE. THE INVERTERS SHALL NOT PUT POWER ON TO THE GRID IF THE GRID IS OFF-LINE.
<br />INVERTERS ARE FULLY COMPLIANT WITH NEC 690.61
<br />27.NOTHING IN THESE PLANS SHALL BE CONSTUED TO CONTRADICT NEC, UL OR LOCAL CODES.
<br />28.ALL SYSTEM COMPONENTS (MODULES AND INVERTERS ETC.) SHALL BE UL LISTED, UL2703 AND UL1703.
<br />29.MOUNT TO ROOF USING UL APPROVED MOUNTING HARDWARE. FOLLOW MANUFACTURERS INSTALLATION MANUALS.
<br />30.MARK THE NEC REQUIRED CLEAR SPACE ON THE FLOOR IN FRONT OF ALL DEVICES BEING INSTALLED.
<br />31.SUPPORT ALL ROOF MOUNTED CONDUIT WITH FOAM "SLEEPERS" IN UL APPROVED SYSTEM.
<br />32.PV MODULES SHALL NOT BE INSTALLED OVER ANY PLUMBING OR MECHANICAL VENTS, EXHAUSTS OR CHIMNEYS.
<br />33.REMOVAL OF INVERTER, METER OR OTHER EQUIPMENT SHALL NOT DISCONNECT THE BONDING CONNECTION BETWEEN THE GROUNDING ELECTRODE CONDUTCTOR
<br />AND THE PHOTOVOTAIC SOURCE AND/OR OUTPUT CIRCUIT GROUNDED CONDUCTOR.
<br />34.ALL PV MODULES AND ASSOCIATED EQUIPMENT SHALL BE PROTECTED FROM ANY PHYSICAL DAMAGE AND ACCESS BY UNQUALIFIED PERSONS
<br />35.UTILITY IS 480Y/277V 3 PHASE 4W. PV SYSTEM IS UTILITY INTERACTIVE.
<br />36.SYSTEM CARRIES A "CLASS A" FIRE RATING.
<br />37.ALL ELECTRICAL WORK SHALL BE DESIGNED PER 2020 LOS ANGELES COUNTY ELECTRICAL CODE, 2019 CALIFORNIA ELECTRICAL CODE, 2017 NATIONAL ELECTRICAL
<br />CODE, AND 2019 BUILDING ENERGY EFFICIENCY STANDARDS.110.2 APPROVAL: ADD NOTE ON THE PLANS STATING ALL ELECTRICAL EQUIPMENT SHALL BE LABELED,
<br />LISTED, OR CERTIFIED BY A NATIONALLY RECOGNIZED TESTING LABORATORY ACCREDITED BY THE UNITED STATES OCCUPATIONAL SAFETY HEALTH ADMINISTRATION
<br />38.THE MAXIMUM COMBINED VOLTAGE DROP ON BOTH INSTALLED FEEDER CONDUCTORS AND BRANCH CIRCUIT CONDUCTORS TO THE FARTHEST CONNECTED LOAD
<br />OR OUTLET SHALL NOT EXCEED 5 PERCENT(ART. 130.5(c) )
<br />ELECTRICAL CONSTRUCTION GENERAL NOTES
<br />6$55$</$<287
<br />CODE INFORMATION
<br />PV PERMIT PACKAGE
<br />2041 E WILSHIRE AVENUE, SANTA ANA, CA 92705
<br />190.12KW GRID TIED SOLAR PHOTOVOLTAIC SYSTEM
<br />PROJECT NAME: FREUDENBERG-NOK
<br />AIN: 402-111-39
<br />NUMBER OF STORIES: 2
<br />COMMERCIAL PROPERTY
<br />CONSTRUCTION TYPE: V-N WITH AUTOMATIC FIRE SPRINKLERS
<br />OCCUPANCY: TYPE B-2 MFG / WAREHOUSE
<br />ROOF TYPE: 60MIL PVC
<br />BUILDING CLEAR HEIGHT: 27FT
<br />FIRE SPRINKLERS: YES
<br />OCCUPANCY CLASSIFICATION: B, S-2, U
<br />PROPERTY TYPE: COMMERCIAL/ INDUSTRIAL
<br />SITE AREA: 68,999 SQ.FT
<br />BUILDING AREA: 27,819 SQ.FT
<br />EXISTING SERVICE - 3-PHASE, 4-WIRE, 480Y/277, 65KAIC
<br />MAIN SERVICE BUS SIZE: 3000A
<br />MAIN CIRCUIT BREAKER SIZE: 3000A
<br />SECTION A: 2000A, SECTION B: 1000A, SECTION C: 1000A, SECTION D: 800A
<br />MAIN SERVICE PANEL BRAND: CUTLER HAMMER
<br />SUBMITTAL FOR CITY BUILDING AND ELECTRICAL REVIEW
<br />SOLAR PHOTOVOLTAIC SYSTEM: THIS PROJECT ENTAILS THE INSTALLATION OF A PHOTOVOLTAIC
<br />SYSTEM AT )5(8'(1%(5*.
<br />WILL BE A NET ENERGY METERING.
<br />THIS SYSTEM WILL BE INTERCONNECTED TO AND WILL BE OPERATED IN PARALLEL WITH THE
<br />ELECTRIC GRID PER THE REQUIREMENTS OF
<br />THE NATIONAL ELECTRICAL CODE AND UTILITY INTERCONNECT AGREEMENT.
<br />CONDITIONS OF APPROVAL:
<br />ALL CONSTRUCTION SHALL OCCUR BETWEEN THE HOURS OF 7AM & 6PM, EXCEPT FOR THE
<br />PURPOSE OF EMERGENCIES
<br />SOLAR (ROOF MOUNT):
<br />(388) HANWHA Q CELLS Q.PEAK 490W MODULES
<br />(3) STP CORE1-62-US (240V) STRING INVERTER
<br />(132) AP SYSTEMS RAPID SHUTDOWN
<br />SYSTEM SIZE (DC STC): 190.12KW
<br />SYSTEM SIZE (AC CEC): 173.69KW
<br />STORM WATER PREVENTION NOTES
<br />STORM WATER POLLUTION PREVENTION DEVICES AND PRACTICES SHALL BE INSTALLED AND/OR INSTITUTED AS NECESSARY TO ENSURE COMPLIANCE WITH THE CITY WATER
<br />QUALITY STANDARDS CONTAINED IN LOCAL REGULATIONS, FEDERAL REGULATIONS AND ANY EROSION CONTROL PLAN ASSOCIATED WITH THIS PROJECT. ALL SUCH DEVICES
<br />AND PRACTICES SHALL BE MAINTAINED, INSPECTED AND/OR MONITORED TO ENSURE ADEQUACY AND PROPER FUNCTION THROUGHOUT THE DURATION
<br />OF THE CONSTRUCTION PROJECT.
<br />COMPLIANCE WITH THE WATER QUALITY STANDARDS AND ANY EROSION CONTROL PLAN ASSOCIATED WITH THIS PROJECT INCLUDES, BUT IS NOT LIMITED TO THE FOLLOWING:
<br />1.ALL POLLUTANTS SHALL BE RETAINED ON SITE UNTIL PROPERLY DISPOSED OF, AND MAY NOT BE TRANSPORTED FROM THE SITE VIA SHEET FLOW, SWALES, AREA DRAINS,
<br />NATURAL DRAINAGE COURSES OR WIND.
<br />2.STOCKPILES OF CONSTRUCTION-RELATED MATERIALS SHALL BE PROTECTED FROM BEING TRANSPORTED FROM THE SITE BY FORCES OF WIND OR WATER FLOW.
<br />3.TRASH AND CONSTRUCTION SOLID WASTES SHALL BE DEPOSITED INTO COVERED RECEPTACLES TO PREVENT CONTAMINATION OF RAINWATER AND DISPERSAL BY WIND.
<br />NOTE:ALL ELECTRICAL WORK SHALL BE DESIGNED PER 2023 LOS ANGELES COUNTY ELECTRICAL CODE, 2022 CALIFORNIA ELECTRICAL CODE, 2022 CALIFORNIA ELECTRICAL
<br />CODE, AND 2020 NATIONAL ELECTRICAL CODE.
<br />NOTE: (110.2) ALL ELECTRICAL EQUIPMENT SHALL BE LABELED, LISTED, OR CERTIFICATE BY A NATIONALLY RECOGNIZED TESTING LABORATORY ACCREDITED BY THE UNITED
<br />STATES OCCUPATIONAL SAFETY HEALTH ADMINISTRATION.
<br />NOTE: 130.5(C) VOLTAGE DROP NOTE: THE MAXIMUM COMBINED VOLTAGE DROP ON BOTH INSTALLED FEEDER CONDUCTORS AND BRANCH CIRCUIT CONDUCTORS TO THE
<br />FARTHEST CONNECTED LOAD OR OUTLET SHALL NOT EXCEED 5 PERCENT.
<br />T1 TITLE PAGE
<br />SPACE FOR STAMP
<br />S6758&785$/'(7$,/6
<br />DESIGNER
<br />DATE
<br />AHJ
<br />UTILITY
<br />MOUNTING SYSTEM
<br />MODULE SCALE
<br />CITY OF SANTA ANA
<br />SCE
<br />SOLLEGA RACKING SYSTEM
<br />(388) HANWHA Q.PEAK 490W (Q.PEAK DUO XL-G10.3/BFG 490)
<br />PROJECT ADDRESS
<br />FREUDENBERG - NOK
<br />2041 E WILSHIRE AVENUE
<br />SANTA ANA, CA 92705
<br />RAHUL DISA
<br />AS INDICATED
<br />03-08-2024
<br />28476 WESTINGHOUSE PLACE, VALENCIA, CA 91355
<br />PHONE: (661) 294-9495
<br />CA LICENSE: #927678 (B, C-10, & C-39)
<br />INVERTER
<br />MARK FIGEARO
<br />(3) STP CORE1-62-US (STP-62-US-41) (480V) STRING INVERTER
<br />D(/&75,&$/DATASHEET
<br />E 1b SINGLE LINE DIAGRAM
<br />DESCRIPTION
<br />190.12 KW (DC) PHOTOVOLTAIC SYSTEM
<br />173.69 KW (CEC-AC) PHOTOVOLTAIC SYSTEM
<br />PAGE NAME
<br />7,7/(3$*(
<br />PAGE NO.
<br />7
<br />D6758&785$/DATASHEET
<br />D6758&785$/DATASHEET
<br />D6758&785$/DATASHEET
<br />D6758&785$/DATASHEET
<br />((/(&75,&$/(48,30(17
<br />S2STRUCTURAL DETAILS
<br />S%8,/',1*(/(9$7,216
<br />Bldg# 101118991
<br />Elec# 20182594
<br />
<br />APPROVALS:
<br />PLNG - ASevilla
<br />BLDG - WLee
<br />ELEC - MSmith
<br />2041 E Wilshire Ave-
<br />101118991 & 201825946/3/2024
|