Laserfiche WebLink
PRINTS ARE THE EXCLUSIVE PROPERTY OF STRATUS. THIS MATERIAL SHALL NOT BE USED, DUPLICATED, OR OTHERWISE REPRODUCED WITHOUT THE PRIOR WRITTEN CONSENT OF STRATUS. <br />ADDRESS: <br />ORDER NUMBER: <br />SITE NUMBER: <br />ELECTRONIC FILE NAME: <br />PROJECT NUMBER: <br />PROJECT MANAGER: <br />PAGE NO.:stratusunlimited.com <br />8 8 8 . 5 0 3 .1 5 6 9 <br />8959 Tyler Boulevard <br />Mentor, Ohio 44060 <br />Rev # Req # Date/Artist DescriptionRev # Req # Date/Artist Description <br />Rev 7 475943 05/09/24 Z-RE 1205134 <br />401 N GRANDE AVE <br />SANTA ANA, CA 92701-4343 <br />86352 <br />JENEVY EIR5403 <br />5 <br />CLIENT: <br />Original <br />Rev 1 <br />Rev 2 <br />Rev 3 <br />Rev 4 <br />Rev 5 <br />Rev 6 <br />458195 <br />459440 <br />459775 <br />462357 <br />462947 <br />470995 <br />472786 <br />01/04/24 RH <br />01/10/24 RH <br />01/12/24 Z-SA <br />02/05/24 Z-CH <br />02/08/24 Z-CH <br />04/04/24 Z-SA <br />04/17/24 Z-RAG:\ACCOUNTS\C\CHEVRON PRODUCTS CO\EXTRA <br />5403_Santa Ana_R6 <br />Revised artwork <br />35.6 square feet <br />approx. 201.41 lbs <br />THIS SIGN IS INTENDED TO BE INSTALLED IN <br />ACCORDANCE WITH THE REQUIREMENTS OF <br />ARTICLE 600 OF THE NATIONAL ELECTRICAL <br />CODE AND/OR OTHER APPLICABLE LOCAL <br />CODES. THIS INCLUDES PROPER GROUNDING <br />AND BONDING OF THE SIGN. <br />THE LOCATION OF THE DISCONNECT SWITCH <br />AFTER INSTALLATION SHALL COMPLY WITH <br />ARTICLE 600.6(A) (1) OF THE NATIONAL <br />ELECTRIC CODE. <br />1'-5-5/8" <br />8-1/8" <br />5'-3-3/4" 2'-11-7/8" <br /> 9'-8-1/2" Backer & Swoosh <br />1'-1/4" <br />1'-6-5/8" <br />Swoosh <br />3-1/2" <br />2-1/2"4-1/2" <br />1" <br />3'-8" <br />Backer <br />SIMULATED NIGHT VIEW <br />Rubber disconnect <br />switch on top right <br />side of panel <br />STUD <br />WALL <br />CONCRET <br />E <br />MASONRY <br />WALL <br />Thru bolt - all thread fasteners w/ wood blocking or angle iron stringer <br />Toggle bolts w/ hollow core- plywood backing <br />Kwik Bolts or Expansion lag bolts & shields w/ solid concrete <br />*MOUNTING METHOD: <br />(Use appropriate method following wall inspection) <br />Silicone caulk all penetrations <br />Steel Angle or approved <br />blocking <br />Plastic Bushing <br />Wire Nut <br />Junction Box <br />Electrical conduit <br />& fitting <br />Anchor bolt (may vary) <br />w/ mounting angle <br />Bolt, Hex head, 1/4”-20 <br />w/ nut & washer <br />#18ga PLTC Wire <br />Power supply box <br />Stud for Grounding <br />Power supply <br />12 ga Stranded THHN Wire <br />Fitting & Conduit - To Primary <br />12 ga Stranded THHN Wire <br />Fitting & Conduit - To Primary <br />Disconnect Switch w/ lock <br />Thru bolt - all thread fasteners w/ wood blocking or angle iron stringer <br />Toggle bolts w/ hollow core- plywood backing <br />Kwik Bolts or Expansion lag bolts & shields w/ solid concrete <br />*MOUNTING METHOD: <br />(Use appropriate method following wall inspection) <br />4mm ACM backer w/ <br />internal angle framework <br />Aluminum returns <br />Polycarbonate Back <br />18 ga PLTC Wire <br />Crimp Connector <br />LED modules <br />Weep holes 5/16” dia <br />w/ light baffle if req’d. <br />Exterior locations only <br />3/8” Riv nut w/ hex bolt <br />& lock washer <br />Acrylic Face <br />Spacer <br />ACM baffle <br />Pan head screw <br />Trimcap <br />FACE/HALO LIT LED | BACKER | REMOTE <br />SS Threaded Rod w/ <br />Hex Nut & Nylock Washer <br />Rubber Disconnect Switch <br />FACES: SWOOSH & “MILE”: 3/16" #7328 White acrylic w/ surface applied trans. Yellow vinyl overlays; <br />“EXTRA”: 3/16" #7328 White acrylic <br />ILLUM.: <br />INSTALL: <br />QUANTITY: <br />FACE ILLUM. (All letters and swoosh): Sloan Prism12 6500K White LED’s as required by manufacturer; <br />SWOOSH HALO ILLUM.: Sloan Prism12 Red LED’s as required by manufacturer; <br />“EXTRA MILE” HALO ILLUM.: Sloan Prism12 Red & 6500K White LED’s as required by manufacturer; <br />Interior 4mm ACM baffle for all letters and swoosh; See following page for LED layouts; <br />REMOTE POWER SUPPLIES; All UL labels to be applied on the bottom right of each illuminated sign; <br />Power to run through standoff, not a separate penetration; Exterior rubber disconnect switch to be added <br />WALL MAT.: <br />Extra Mile & Swoosh to be pin mounted off backer surface with 1" x 1/2" dia. spacer painted to match backer <br />to allow for halo illumination; Backer thru bolted to wall surface using all thread into blocking as required; <br />12" standard length of threaded rod will be supplied unless otherwise noted; 3/8" threaded rod into blocking <br />or Stratus approved equivalent; Spacers to be provided andAll nuts are to be Nylock to resist back out; <br />painted to match backer; Eye bolt to be removed and plug to be inserted and painted Chevron Red after install is complete <br />Compression sleeves required to avoid crushing wall & achieve max tensioning <br />TRIMCAP: <br />RETURNS: <br />BACKS: <br />SWOOSH: 3/4" Yellow Jewelite trimcap; All trimcap seams to be on top of swoosh <br />“EXTRA MILE”: 3/4" Gray Jewelite trimcap; All trimcap seams to be on top of letters <br />3/16" Clear polycarbonate w/ second surface applied 3M 3630-73 Dark Red vinyl overlays <br />(1) ONE LETTERSET on BACKER REQUIRED FOR WEST ELEVATION <br />Stucco <br />BACKER: <br />SWOOSH: 3-1/2" deep .040 alum. painted Yellow; <br />“EXTRA MILE”: 4-1/2" deep .040 alum. painted Gray <br />3" x 3" x 1-1/2" x 1/8" angle iron glued to inside corners of brake formed 4mm TOR Red Alpolic ACM with <br />2-1/2" returns; Additional 1-1/2" x 1-1/2" 1/8" angle glued to the top inside length of the backer, to run the length <br />of backer; 2" x 2" x 1/8" angle frame for attaching to wall with 1" x 1" notch cut to accept eyebolt <br />TOR Red Alpolic ACM <br />COLOR PALETTE <br />PMS 7405 C Yellow <br />3M 3630-15 Yellow <br />All paint finishes to be Satin <br />unless otherwise noted <br />PMS Cool Gray 10 C <br />Scale: 3/4"=1'-0" <br />FACE / HALO LIT CHANNEL LETTERS ON PANEL 44-PCE01 <br />Updated art board <br />401 N Grand Ave - <br />1011198557/29/2024