Laserfiche WebLink
CONTINUE PLYWOOD AND METAL STUD <br />FRAMING TO UNDERSIDE OF EXISTING <br />ROOF FRAMING <br />EXISTING PLYWOOD ROOF DECK <br />EXISTING 2x ROOF FRAMING <br />CONTINUOUS SLIP TRACK WITH 2" <br />FLANGE. WITH W/4-10g SCREWS @ <br />EA FRAMING MEMBER. <br />VARIES <br />V.I.F. <br />9/ <br />1 <br />6 <br />" <br />9/ <br />1 <br />6 <br />" <br />20 GAUGE, 3 5/8" METAL STUD WALL FRAMING AT 8" O.C. <br />AT INVENTORY ROOMS. PROVIDE 16" O.C. AT NON- <br />INVENTORY ROOM WALLS <br />NOTE: PROVIDE FIRE SEALANT AT <br />ANY PENETRATIONS IN RATED WALLS <br />PROVIDE (1) LAYER 5/8" GYPSUM <br />BOARD ON THIS SIDE. HOLD <br />BOTTOM EDGE 1/4" ABOVE FINISH <br />FLOOR. FASTEN TO METAL STUDS <br />WITH #6 X 1 5/8" DRYWALL <br />SCREWS 12" O.C. IN FIELD AND <br />8" O.C. AT SEAMS. <br />NON-INVENTORY SIDE <br />4" BASE (SEE INTERIOR FINISHES SCHEDULE) <br />PROVIDE (1) LAYER 5/8" GYPSUM BOARD ON <br />(1) LAYER 3/4" CDX FIRE RETARDANT <br />PLYWOOD ON INSIDE SURFACE OF ALL <br />INVENTORY WALLS <br />BATT INSULATION FULL HEIGHT OF PARTITION <br />INVENTORY SIDE <br />PROVIDE FIRE INSULATION AS REQUIRED <br />FOR FIRE STOPPING <br />CONTINUOUS TRACK W/ 1/4" ∅, 3/4" LONG HILTI <br />POWDER ACTUATED ANCHORS @ 32" O.C. <br />CONTINUE GYPSUM BOARD AND <br />METAL STUD FRAMING TO 6" <br />ABOVE SUSPEND. CLG. <br />FINISHED FLOOR 0'-0" <br />VARIES <br />SEE PLAN <br />6" <br />SLATWALL, SEE F.F.E. PLAN <br />DETAIL TYPICAL FOR WALL TYPE 4A4A <br />WALL TYPE <br />SEE DETAIL 10 <br />NOTE: <br />ATTACH BOTTOM OF BRACE TO TOP TRACK OF WALL WITH (3) #8 SHEET <br />METAL SCREWS EACH BRACE. DO NOT ATTACH THROUGH CEILING TILE. <br />(2) 7/16" #8 SHARP POINT SCREWS <br />METAL SLIP TRACK ATTACHED TO <br />FRAMING, DECK OR CROSS BRACE <br />WITH #8 SCREWS (TYP. AT EACH END) <br />20 GA., 3 5/8" STUD BRACE <br />AT 8'-0" O.C. MAX. ALTERNATE <br />DIRECTIONS <br />PROVIDE 1/2" <br />GAP BETWEEN <br />BRACE & <br />FRAMING OR <br />DECK FOR <br />DEFLECTION. <br />8" <br /> <br />NOTE: <br />UNISTRUT SHALL BE CONNECTED TO <br />EXISTING JOISTS ± 6" WITHIN PANEL <br />POINTS WITH P1000 UNISTRUT <br />FASTENERS AND BOLTED BETWEEN <br />OPEN WEB STEEL JOIST FLANGES AT <br />CONTRACTORS DISCRETION (TYP.) <br />NOTE: <br />ICC-ES # FOR METAL STUDS.........ESR-3064P <br />(STUDS SHALL BE PER "STEEL STUD <br />MANUFACTURERS ASSOCIATION") <br />ICC-ES # FOR FASTENERS..........ESR-3056 <br />(ITW "SHEET METAL" BUILDEX SCREWS) <br />ICC-ES # FOR SHOT PINS..........ESR-1663 <br />(.145" ∅POWDER DRIVEN HILTI PINS) <br />3 5/8" METAL STUD <br />5/8" GYPSUM BOARD (TYP.) <br />FULL INSULATION (TYP.) <br />ATTACH CABINET AS PER <br />MANUFACTURER'S SPECIFICATIONS <br />LARSEN C2409-R CABINET. <br />SEE ARCH PLAN FOR HINGE <br />ORIENTATION. SPECIFY ORIENTATION <br />WHEN ORDERING. <br />5 <br />A.5.0 <br />LINE OF ROUGH <br />OPENING <br />R. <br />O <br />. <br />2' <br />- <br />1 <br />" <br />R.O. <br />10 1/2" <br />FL <br />O <br />O <br />R <br /> <br />T <br />O <br /> <br />H <br />E <br />A <br />D <br />4' <br />- <br />0 <br />" <br />EXISTING WALL TO REMAIN <br />EXISTING STOREFRONT SYSTEM <br />SECURITY SHUTTER RAIL GUIDE <br />STOREFRONT FRAME BEYOND <br />SECURITY SHUTTER HEADER BOX <br />MOUNTED TO EXISTING WALL <br />SECURITY SHUTTER STOPS <br />AT FINISH FLOOR <br />FINISH FLOOR 0'-0" <br />TOP OF EXISTING <br />STOREFRONT <br />VARIES <br />V.I.F. <br />SECURITY SHUTTER POST <br />1/2" THICK SOLID SURFACE SILL WITH HALF <br />BULLNOSE EDGE BY CABINET CONTRACTOR. <br />OVERHANG 1/2" FROM FACE OF WALL BELOW. <br />EXISTING WINDOW SYSTEM <br />CONTINUOUS SEALANT <br />AT WINDOW FRAME <br />AND SILL JOINT <br />PATCH AND REPAIR <br />SURFACE AS REQUIRED FOR <br />CORIAN SOLID SURFACE <br />SILL INSTALLATION. <br /> 1/2"CAULK <br />EXISTING WALL <br />EXISTING WINDOW SILL <br />20 GAUGE, 2 1/2" METAL STUD WALL FRAMING <br />AT 16" O.C. <br />4" BASE (SEE INTERIOR FINISHES SCHEDULE) <br />BATT INSULATION, FULL HEIGHT <br />CONTINUOUS TRACK W/ 1/4" ∅, 3/4" LONG HILTI <br />POWDER ACTUATED ANCHORS @ 32" O.C. <br />(1) LAYER 5/8" GYPSUM BOARD. <br />ALIGN FACE OF GYPSUM BOARD <br />EXISTING WALL BEYOND <br />GC TO COORDINATE SHUTTER INSTALLATION WITH NEW <br />SILL TO ENSURE PROPER CLEARANCE <br />EXISTING PLANTER <br />EXISTING WALL TO REMAIN <br />SUSPENDED CEILING <br />SECURITY SHUTTER RAIL GUIDE <br />TRACK MOUNTED TO WINDOW JAMB <br />EXISTING STOREFRONT SYSTEM <br />SECURITY SHUTTER RAIL GUIDE <br />STOREFRONT FRAME BEYOND <br />SECURITY SHUTTER HEADER <br />BOX MOUNTED TO <br />STOREFRONT FRAMING <br />SECURITY SHUTTER STOPS <br />AT FINISH FLOOR <br />FINISH FLOOR 0'-0" <br />TOP OF EXISTING <br />STOREFRONT <br />VARIES <br />V.I.F. <br />CEILING EDGE SUPPORT ANGLE <br />CONTINUE METAL STUD <br />FRAMING TO UNDERSIDE OF EXISTING <br />ROOF FRAMING <br />EXISTING PLYWOOD ROOF DECK <br />EXISTING 2x ROOF FRAMING <br />CONTINUOUS SLIP TRACK WITH 2" <br />FLANGE. WITH W/4-10g SCREWS @ <br />EA FRAMING MEMBER. <br />VARIES <br />V.I.F. <br />9/ <br />1 <br />6 <br />" <br />9/ <br />1 <br />6 <br />" <br />20 GAUGE, 3 5/8" METAL STUD WALL FRAMING AT 16" O.C. <br />NOTE: PROVIDE FIRE SEALANT AT <br />ANY PENETRATIONS IN RATED WALLS <br />4" BASE (SEE INTERIOR FINISHES SCHEDULE) <br />BATT INSULATION FULL HEIGHT OF PARTITION <br />PROVIDE FIRE INSULATION AS REQUIRED <br />FOR FIRE STOPPING <br />CONTINUOUS TRACK W/ 1/4" ∅, 3/4" LONG HILTI <br />POWDER ACTUATED ANCHORS @ 32" O.C. <br />CONTINUE GYPSUM BOARD TO <br />6" ABOVE SUSPEND. CLG. <br />FINISHED FLOOR 0'-0" <br />VARIES <br />SEE PLAN <br />(1) LAYER 5/8" GYPSUM BOARD ON BOTH SIDES OF <br />FRAMING. HOLD BOTTOM EDGE 1/4" ABOVE FINISH FLOOR. <br />FASTEN TO METAL STUDS WITH #6 X 1 5/8" DRYWALL <br />SCREWS 12" O.C. IN FIELD AND 8" O.C. AT SEAMS. <br />6" <br />1 DETAIL TYPICAL FOR WALL TYPE 1 <br />2 SAME AS WALL TYPE 1 EXCEPT: INSTALL 3/4" CDX <br />PLYWOOD IN LIEU OF GYPSUM BOARD ON TELCO SIDE <br />WALL TYPE <br />SEE DETAIL 10 <br />1' <br />- <br />5 <br /> <br />1 <br />/ <br />2 <br />" <br />2' <br />- <br />4 <br /> <br />1 <br />/ <br />4 <br />" <br />3" THICK BRICK TO <br />MATCH EXISTING AT <br />PLANTER <br />4" <br />8" <br />NEW CONCRETE BLOCK AND <br />NEW FOOTING. <br />NEW 4" CONCRETE SIDEWALK, <br />ALIGN WITH EXISTING <br />FILL WITH <br />CONCRETE, TYP. <br />SIDEWALK0'-0" <br />FULL BRICK AT TOP <br />TO MATCH EXISTING <br />HORIZONTAL <br />REINFORCING <br />INTENT IS FOR NEW PLANTER <br />WALL TO MATCH EXISTING <br />1"1 1/2" <br />11 1/2" <br />CONTINUE GYPSUM BOARD AND METAL <br />STUD FRAMING TO UNDERSIDE OF <br />EXISTING ROOF FRAMING <br />EXISTING PLYWOOD ROOF DECK <br />EXISTING 2x ROOF FRAMING <br />CONTINUOUS SLIP TRACK WITH 2" <br />FLANGE. WITH W/4-10g SCREWS @ <br />EA FRAMING MEMBER. <br />VARIES <br />V.I.F. <br />9/ <br />1 <br />6 <br />" <br />9/ <br />1 <br />6 <br />" <br />20 GAUGE, 3 5/8" METAL STUD WALL FRAMING AT 16" O.C. <br />NOTE: PROVIDE FIRE SEALANT AT <br />ANY PENETRATIONS IN RATED WALLS <br />4" BASE (SEE INTERIOR FINISHES SCHEDULE) <br />BATT INSULATION FULL HEIGHT OF PARTITION <br />PROVIDE FIRE INSULATION AS REQUIRED <br />FOR FIRE STOPPING <br />CONTINUOUS TRACK W/ 1/4" ∅, 3/4" LONG HILTI <br />POWDER ACTUATED ANCHORS @ 32" O.C. <br />FINISHED FLOOR 0'-0" <br />VARIES <br />SEE PLAN <br />(1) LAYER TYPE X 5/8" GYPSUM BOARD ON BOTH SIDES OF <br />FRAMING. HOLD BOTTOM EDGE 1/4" ABOVE FINISH FLOOR. <br />FASTEN TO METAL STUDS WITH #6 X 1 5/8" DRYWALL <br />SCREWS 12" O.C. IN FIELD AND 8" O.C. AT SEAMS. <br />6 DETAIL TYPICAL FOR WALL TYPE 6 <br />WALL TYPE <br />SEE DETAIL 10 <br />6A SAME AS DETAIL 6 BUT INSTALL 3/4" CDX PLWOOD <br />ON TOP OF GYPSUM BOARD ON TELCO SIDE <br />CONTINUE METAL STUD FRAMING TO <br />UNDERSIDE OF EXISTING ROOF FRAMING <br />EXISTING PLYWOOD ROOF DECK <br />EXISTING 2x ROOF FRAMING <br />CONTINUOUS SLIP TRACK WITH 2" <br />FLANGE. WITH W/4-10g SCREWS @ EA <br />FRAMING MEMBER. (SEE DETAIL 10) <br />VARIES <br />V.I.F. <br />9/ <br />1 <br />6 <br />" <br />9/ <br />1 <br />6 <br />" <br />20 GAUGE, 6" METAL STUD FRAMING AT 16" O.C. <br />NOTE: PROVIDE FIRE SEALANT AT <br />ANY PENETRATIONS IN RATED WALLS <br />BATT INSULATION FULL HEIGHT OF PARTITION <br />PROVIDE FIRE <br />INSULATION AS <br />REQUIRED <br />FOR FIRE STOPPING <br />CONTINUE GYPSUM <br />BOARD TO 6" ABOVE <br />SUSPEND. CLG. <br />11'-1" <br />A.F.F. <br />(1) LAYER 5/8" GYPSUM BOARD <br />6" <br />SEE PLAN <br />20 GAUGE, 3 5/8" METAL STUD <br />WALL FRAMING AT 16" O.C. <br />20 GAUGE, 3 5/8" METAL STUD <br />WALL FRAMING AT 16" O.C. <br />11'-0" <br />A.F.F. <br />6" <br />5/8" GYPSUM BOARD. <br />9/ <br />1 <br />6 <br />" <br />9/ <br />1 <br />6 <br />" <br />CONTINUE GYPSUM BOARD TO <br />6" ABOVE SUSPEND. CLG.20 GAUGE, 3 5/8" METAL <br />STUD BRACING AT 48" O.C. <br />Kenneth A. Gruskin AIA <br />No. Date Description <br />Consultant: <br />Checked By: <br />Drawn By: <br />Job Address: <br />Drawing Title: <br />Revision Issue: <br />Professional Seal: <br />Drawing Number: <br />2024 Gruskin Architecture + Design, P.C.c <br />This document and the ideas and designs incorporated <br />herein, as an instrument of professional service, is the <br />property of GRUSKIN ARCHITECTURE + DESIGN, P.C., <br />and is not to be used in whole or in part for any other <br />project without the written authorization of GRUSKIN <br />ARCHITECTURE + DESIGN, P.C. <br />North <br />Arrow: <br />Job Name and Number: <br />Date Issued For <br />All Rights Reserved <br />Client: <br />Landlord: <br />Permit: <br />Bid: <br />Construction: <br />0006261 <br />AR91629 <br />5421 <br />9613 <br />39209 <br />10635 <br />2537 <br />11016 <br />5734 <br />ARC 2596 <br />4674 <br />2666 <br />AI 09999 <br />2796 <br />0401 011223 <br />2572 <br />17680 <br />RA-015432-B <br />025528-1 NY <br />TX <br />VA <br />VT <br />MA <br />MT <br />RI <br />PA <br />NY <br />NJ <br />NH <br />MD <br />LA <br />ME <br />KS <br />FL <br />DE <br />CT <br />AZ <br />AL <br />C-1967WY <br />RA011075GA <br />AR10400066IN <br />C 29898CA <br />NM 004168 <br />ARC-400347CO <br />HI AR 11489 <br />PR 19965 <br />OR 4899 <br />SC 6834 <br />NC 9961 <br />13761OH <br />05713IA <br />WV 3727 <br />IL 001-019152 <br />UT 5881358-0301 <br />ID AR-984459 <br />1301052379MI <br />ARC100723DC <br />WI 9900-005MN 44326 <br />A-3547NE <br />3811AR <br />5967KY 101374TN <br />MS 3860 <br />1666ND <br />A-2005029740MO <br />a4895OK <br />NV 5521 <br />WA 10344 <br />13167AK <br />SD 11532 <br />J: <br />\ <br />V <br />e <br />r <br />i <br />z <br />o <br />n <br />\ <br />0 <br />0 <br /> <br />S <br />t <br />o <br />r <br />e <br />s <br /> <br />b <br />y <br /> <br />S <br />t <br />a <br />t <br />e <br />\ <br />C <br />a <br />l <br />i <br />f <br />o <br />r <br />n <br />i <br />a <br />\ <br />2 <br />0 <br />2 <br />3 <br />- <br />0 <br />0 <br />6 <br />9 <br /> <br />M <br />e <br />t <br />r <br />o <br /> <br />P <br />o <br />i <br />n <br />t <br />e <br />- <br />S <br />a <br />n <br />t <br />a <br /> <br />A <br />n <br />a <br />, <br /> <br />C <br />A <br />\ <br />2 <br />. <br />D <br />r <br />a <br />w <br />i <br />n <br />g <br />s <br />\ <br />2 <br />. <br />4 <br /> <br />C <br />D <br />\ <br />0 <br />0 <br />- <br />2 <br />0 <br />2 <br />3 <br />- <br />0 <br />0 <br />6 <br />9 <br />- <br />C <br />u <br />r <br />r <br />e <br />n <br />t <br />\ <br />2 <br />0 <br />2 <br />3 <br />- <br />0 <br />0 <br />6 <br />9 <br />- <br />B <br />I <br />M <br />2 <br />3 <br />. <br />r <br />v <br />t <br />2023-0069 <br />Proposed <br />Store Design <br />for: VERIZON <br />Metro Pointe <br />3500 South Bristol Street <br />Suite 100 <br />Santa Ana, CA 92704 <br />3/15/24 <br />3/15/24 <br />ARCHITECTURAL DETAILS <br />A.5.0 <br />MB <br />KG <br />22 OF 81 <br />3/4" = 1'-0"2 WALL UP TO STRUCTURE ABOVE @ INVENTORY <br />Version: 050319 1 1/2" = 1'-0"10 STUD BRACING DETAIL <br />Version: 050818 <br />1" = 1'-0"4 <br />PLAN DETAIL FOR <br />FIRE EXTINGUISHER CABINET <br />Version: 050818 <br />1" = 1'-0"5 <br />ELEVATION FOR <br />FIRE EXTINGUISHER CABINET <br />Version: 050818 <br />1 1/2" = 1'-0"7 TYP. SECURITY SHUTTER SECTION - RETAIL SALES <br />Version: 110520 <br />1 1/2" = 1'-0"8 SILL DETAIL (EXPLODED) <br />Version: 050818 <br />1 1/2" = 1'-0"6 TYP. SECURITY SHUTTER SECTION-BOH <br />Version: 110520 <br />3/4" = 1'-0"1 WALL UP TO STRUCTURE ABOVE <br />Version: 050319 <br />1 1/2" = 1'-0"9 PLANTER DETAIL <br />Version: 050818 <br />3/4" = 1'-0"3 WALL UP TO STRUCTURE ABOVE - DEMISING WALL <br />Version: 050319 <br />3/4" = 1'-0"11 WALL UP TO STRUCTURE ABOVE <br />Version: 050319 <br />3500 S Bristol St Unit# 100 - <br />101119098, 20182666 & <br />401390437/11/2024