1105 S Karen Ave - Plan - Laserfiche WebLink

Home Browse Search

SHEET NAME SHEET SIZE SHEET NUMBER ANSI B 11" X 17" SIGNATURE WITH SEAL PROJECT NAME & ADDRESS E1.0 DATE: 1/17/2024 11 0 5 S K A R E N A V E SA N T A A N A , CA , 92 7 0 4 JO R G E M A G A L L O N R E S I D E N C E DESCRIPTION DATE REV REVISIONS INITIAL DESIGN 1/17/2024 00 LEVION CONSTRUCTION LLC 2020 IOWA AVE SUITE 103, RIVERSIDE, CA 92507 CONTRACTOR LIC#: #1096696 PHONE #: 951-554-2201 GENERAL B ZACHARY WINGER NOTES NOTES NOTE:- (1) ENCHARGE BATTERY SYSTEM ENERGY CAPACITY SHALL BE SIZED TO SUPPLY ALL DESIRED LOADS DURING AN OUTAGE. POWER CAPACITY OF THE ENCHARGE BATTERY SYSTEM SHALL BE CAPABLE OF SUPPLYING THE LARGEST LOAD ON SITE, PER 2022 CEC 710.15(A) & CEC 710.15(E). (2) ENCHARGE BATTERY STORAGE DISCONNECT SHALL BE SECURED USING AN EATON TYPE-BR CIRCUIT BREAKER HOLD DOWN KIT #BRHDK125 (3) DISTANCE BETWEEN ENPOWER AND ENCHARGE SHOULD BE LESS THEN 5' ELSE AN AC DISCONNECT WILL BE REQUIRED (4) INSTALLER TO VERIFY HOW ENCLOSURE ARE COUPLED TOGETHER VIA CHASE NIPPLE/ CONDUIT 1.AFCI PROTECTION IS REQUIRED WHEN LOADS ARE RELOCATED MORE THAN 6' [210.12(D)]. 2.THE PV BREAKER SHALL BE AT THE FURTHEST POSITION AWAY FROM THE MAIN BREAKER [CEC 705.12(B)(2)(3)(B)]. 3.PV BREAKER(S) MAY CONNECT AT EITHER END, BUT NOT BOTH ENDS, OF A CENTER-FED PANEL [CEC 705.12(B)(2)(3)(D)]. 4.THE BACK-FED BREAKER SHALL BE SECURED IN PLACE BY AN ADDITIONAL FASTENER PER SECTION [408.36 (D)]. 5.VERIFY UFER OR ADD GROUND RODS (MIN. 2) SPACED A MIN. 6' APART (CEC 250). 6.BOND COLD WATER AND GAS LINES TO GROUNDING ELECTRODE CONDUCTOR PER [CEC 250.105(A)&(B)]. 7.PANEL MODIFICATIONS REQUIRE A 3RD/ PARTY FIELD EVALUATION, TO RECERTIFY THE MODIFIED PANEL. THE EVALUATION REPORT IS TO BE GIVEN TO THE INSPECTOR AT TIME OF INSPECTION. IF UNABLE TO RECERTIFY A NEW PANEL WILL BE REQUIRED. 1.THIS SYSTEM SHALL COMPLY WITH ALL APPLICABLE CODES (MENTIONED ON PAGE1) INCLUDING:UL STANDARD 1741,AND THE MANUFACTURERS' LISTINGS AND INSTALLATION INSTRUCTIONS. 2.ALL WORK TO COMPLY WITH CEC 3.UTILITY SHALL BE NOTIFIED BEFORE ACTIVATION OF PV 4.REMOVAL OF A UTILITY-INTERACTIVE MICRO-INVERTER OR OTHER EQUIPMENT SHALL NOT SYSTEM DISCONNECT THE BUILDING CONNECTION BETWEEN THE GROUNDING ELECTRODE CONDUCTOR AND THE PV SOURCE AND/OR OUTPUT CIRCUIT GROUNDED CONDUCTOR 5.ALL PV SYSTEM COMPONENTS SHALL BE LISTED BY A RECOGNIZED TESTING 6.WIRING MATERIALS SHALL COMPLY WITH MAXIMUM CONTINUOUS CURRENT OUTPUT AGENCY AT 25° C; WIRE SHALL BE WET RATED AT 90°C 7.EXPOSED PHOTOVOLTAIC SYSTEM CONDUCTORS ON THE ROOF WILL BE USE-2 OR PV TYPE WIRE. 8.ALL EXTERIOR CONDUIT, FITTINGS, AND BOXES SHALL BE RAIN-TIGHT AND APPROVED FOR USE IN WET LOCATIONS 9.ALL METALLIC RACEWAYS AND EQUIPMENT SHALL BE BONDED AND ELECTRICALLY CONTINUOUS 10.FOR UNGROUNDED SYSTEMS, THE PHOTOVOLTAIC SOURCE AND OUTPUT CIRCUITS SHALL BE PROVIDED WITH A GROUND-FAULT PROTECTION DEVICE OR SYSTEM THAT DETECTS A GROUND FAULT, INDICATES THAT FAULT HAS OCCURED, AND AUTOMATICALLY DISCONNECTS ALL CONDUCTORS OR CAUSES THE MICRO-INVERTER TO AUTOMATICALLY CEASE SUPPLYING POWER TO OUTPUT CIRCUITS (CEC 690.35(C)) 11.ANY REQUIRED GROUNDING ELECTRODE CONDUCTOR WILL BE CONTINUOUS, EXCEPT FOR SPLICES OR JOINTS AT BUSBARS WITHIN LISTED EQUIPMENT (CEC 250.64C) 12.ALL PV MODULES AND ASSOCIATED EQUIPMENT SHALL BE PROTECTED FROM ANY PHYSICAL DAMAGE 13.ALL FIELD-INSTALLED JUNCTION, PULL, AND OUTLET BOXES LOCATED BEHIND MODULES SHALL BE ACCESSIBLE DIRECTLY OR BY DISPLACEMENT OF A MODULE SECURED BY REMOVABLE FASTENERS 14.FOR GROUNDED SYSTEMS, THE MICRO-INVERTER IS EQUIPPED WITH GROUND FAULT PROTECTION AND A GFI FUSE PORT FOR GROUND FAULT INDICATION 15.WHEN BACKFED BREAKER IS THE METHOD OF UTILITY INTERCONNECTION, THE BREAKERS SHALL NOT READ "LINE AND LOAD" 16.THE INSTALLED SOLAR SYSTEM HAS A DISTRIBUTED WEIGHT OF LESS THAN 4 PSF 17.THE CONCENTRATED LOAD FOR EACH VERTICAL SUPPORT IS LESS THAN 45 LBS 19.THE WORKING CLEARANCES AROUND THE EXISTING ELECTRICAL EQUIPMENT AS WELL 18.AC DISCONNECT IS A "KNIFE BLADE" TYPE DISCONNECT AS THE NEW ELECTRICAL EQUIPMENT WILL BE MAINTAINED 20.THE PHOTOVOLTAIC MICRO-INVERTER WILL BE LISTED AS UL 1741 21.SMOKE ALARMS AND CARBON MONOXIDE ALARMS ARE REQUIRED TO BE RETROFITTED COMPLIANT ONTO THE EXISTING DWELLING AS PER THE 2022 CRC. THESE SMOKE ALARMS ARE REQUIRED TO BE IN ALL BEDROOMS, OUTSIDE EACH BEDROOM, AND AT LEAST ONE ON EACH FLOOR OF THE HOUSE. CARBON MONOXIDE ALARMS ARE REQUIRED TO BE RETROFITTED OUTSIDE EACH BEDROOM AND AT LEAST ONE ON EACH FLOOR OF THE HOUSE. THESE ALARMS MAY BE SOLELY BATTERY OPERATED IF THE PHOTOVOLTAIC PROJECT DOES NOT INVOLVE THE REMOVAL OF INTERIOR WALL AND CEILING FINISHES INSIDE THE HOME; OTHERWISE, THE ALARMS MUST BE HARD WIRED AND INTERCONNECTED. (CRC R314, R315) 22.SMOKE AND CARBON MONOXIDE ALARMS ARE REQUIRED PER CRC SECTIONS R314 AND 315 TO BE VERIFIED AND INSPECTED BY THE INSPECTOR IN THE FIELD. 23.WHEN APPLYING THE 120% RULE OF CEC 705.12(D)(2), THE SOLAR BREAKER TO BE POSITIONED AT THE OPPOSITE END OF THE BUS FROM THE MAIN BREAKER PER 705.12(D)(7) 24.PLUMBING AND MECHANICAL VENTS THROUGH THE ROOF SHALL NOT BE COVERED BY SOLAR MODULES - NO BUILDING, PLUMBING, OR MECHANICAL VENTS TO BE COVERED OR OBSTRUCTED 25.EXISTING UFER. IF THERE IS NO UFER,INSTALL (2) NEW 5/8"X8' GROUND ROD 6' APART.WATER BOND <5' FROM BLDG ENTRANCE. #4 AWG GEC TO BOND GROUND ROD AND WATER PIPE. SPLICES SHALL BE IRREVERSIBLE CRIMPED 26.PLAQUES SHALL BE METAL OR PLASTIC, WITH ENGRAVED OR MACHINE PRINTED LETTERS, OR ELECTRO-PHOTO PLATING, IN A CONTRASTING COLOR TO THE PLAQUE-PLACARD IS TWO COLOR/RED FACE-WHITE CORE ENGRAVED PLASTIC. PLAQUE SHALL BE ATTACHED TO THE SERVICE EQUIPMENT WITH POP-RIVETS OR SCREWS.PLAQUE AT MSP 27. THE PV DISCONNECTING MEANS SHALL BE INSTALLED AT A READILY ACCESSIBLE LOCATION EITHER ON THE OUTSIDE OF A BUILDING OR STRUCTURE OR INSIDE NEAREST THE POINT OF ENTRANCE OF THE SYSTEM CONDUCTORS. A SINGLE, VISIBLE-OPEN, LOCKABLE AC DISCONNECT SHALL BE WITHIN THREE FEET OF THE METER ON THE EXTERIOR OF THE BUILDING. 1 1105 S Karen Ave 8/22/2024