|
Job No:
<br />Drawn by:
<br />Sheet:
<br />G-3
<br />Date:
<br />Scale:N.T.S.
<br />DA
<br />T
<br />E
<br />DE
<br />S
<br />C
<br />R
<br />I
<br />P
<br />T
<br />I
<br />O
<br />N
<br />RE
<br />V
<br />I
<br />S
<br />I
<br />O
<br />N
<br />5.504.4.3 Paints and coatings. Architectural paints and coatings shall comply with VOC limits in Table 1 of
<br />the ARB Architectural Coatings Suggested Control Measure, as shown in Table 5.504.4.3, unless more
<br />stringent local limits apply. The VOC content limit for coatings that do not meet the definitions for the specialty
<br />coatings categories listed in Table 5.504.4.3 shall be determined by classifying the coating as a Flat, Nonflat
<br />or Nonflat-High Gloss coating, based on its gloss, as defined in Subsections 4.21, 4.36 and 4.37 of the 2007
<br />California Air Resources Board Suggested Control Measure, and the corresponding Flat, Nonflat or
<br />Nonflat-High Gloss VOC limit in Table 5.504.4.3 shall apply.
<br />5.504.4.3.1 Aerosol Paints and coatings. Aerosol paints and coatings shall meet the PWMIR Limits for
<br />ROC in Section 94522(a)(3) and other requirements, including prohibitions on use of certain toxic
<br />compounds and ozone depleting substances, in Sections 94522(c)(2) and (d)(2) of California Code of
<br />Regulations, Title 17, commencing with Section 94520; and in areas under the jurisdiction of the
<br />Bay Area Air Quality Management District additionally comply with the percent VOC by weight of product
<br />limits of Regulation 8 Rule 49.
<br />5.504.4.4.1 Carpet cushion. All carpet cushion installed in the building interior shall meet the
<br />requirements of the California Department of Public Health,"Standard Method for the Testing and
<br />Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental
<br />Chambers,"Version 1.2, January 2017 (Emission testing method for California Specifications
<br />01350).
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />https://www.cdph.ca.gov/Programs/CCDPHP/DEODC/EHLB/IAQ/Pages/VOC.aspx#material
<br />5.504.4.4.2 Carpet adhesive. All carpet adhesive shall meet the requirements of Table 5.504.4.1.
<br />5.504.4.5 Composite wood products. Hardwood plywood, particleboard and medium density fiberboard
<br />composite wood products used on the interior or exterior of the buildings shall meet the requirements for
<br />formaldehyde as specified in ARB's Air Toxics Control Measure (ATCM) for Composite Wood (17 CCR 93120 et
<br />seq.). Those materials not exempted under the ATCM must meet the specified emission limits, as shown in
<br />Table 5.504.4.5.
<br />5.504.4.5.3 Documentation. Verification of compliance with this section shall be provided as
<br />requested by the enforcing agency. Documentation shall include at least one of the following:
<br />1. Product certifications and specifications.
<br />2. Chain of custody certifications.
<br />3. Product labeled and invoiced as meeting the Composite Wood Products regulation (see
<br /> CCR, Title 17, Section 93120, et seq.).
<br />4. Exterior grade products marked as meeting the PS-1 or PS-2 standards of the
<br /> Engineered Wood Association, the Australian AS/NZS 2269 or European 636 3S
<br /> standards.
<br />5. Other methods acceptable to the enforcing agency.
<br />TABLE 5.504.4.1 - ADHESIVE VOC LIMIT1,2
<br />Less Water and Less Exempt Compounds in Grams per Liter
<br />ARCHITECTURAL APPLICATIONS CURRENT VOC LIMIT
<br />INDOOR CARPET ADHESIVES 50
<br />CARPET PAD ADHESIVES 50
<br />OUTDOOR CARPET ADHESIVES 150
<br />WOOD FLOORING ADHESIVES 100
<br />RUBBER FLOOR ADHESIVES 60
<br />SUBFLOOR ADHESIVES 50
<br />CERAMIC TILE ADHESIVES 65
<br />VCT & ASPHALT TILE ADHESIVES 50
<br />DRYWALL & PANEL ADHESIVES 50
<br />COVE BASE ADHESIVES 50
<br />MULTIPURPOSE CONSTRUCTION ADHESIVES 70
<br />STRUCTURAL GLAZING ADHESIVES 100
<br />SINGLE-PLY ROOF MEMBRANE ADHESIVES 250
<br />OTHER ADHESIVES NOT SPECIFICALLY LISTED 50
<br />SPECIALTY APPLICATIONS
<br />PVC WELDING 510
<br />CPVC WELDING 490
<br />ABS WELDING 325
<br />PLASTIC CEMENT WELDING 250
<br />ADHESIVE PRIMER FOR PLASTIC 550
<br />CONTACT ADHESIVE 80
<br />SPECIAL PURPOSE CONTACT ADHESIVE 250
<br />STRUCTURAL WOOD MEMBER ADHESIVE 140
<br />TOP & TRIM ADHESIVE 250
<br />SUBSTRATE SPECIFIC APPLICATIONS
<br />METAL TO METAL 30
<br />PLASTIC FOAMS 50
<br />POROUS MATERIAL (EXCEPT WOOD)50
<br />WOOD 30
<br />FIBERGLASS 80
<br />1. IF AN ADHESIVE IS USED TO BOND DISSIMILAR SUBSTRATES TOGETHER, THE ADHESIVE
<br />WITH THE HIGHEST VOC CONTENT SHALL BE ALLOWED.
<br />2. FOR ADDITIONAL INFORMATION REGARDING METHODS TO MEASURE THE VOC
<br />CONTENT SPECIFIED IN THIS TABLE, SEE SOUTH COAST AIR QUALITY MANAGEMENT
<br />DISTRICT RULE 1168, www.arb.ca.gov/DRDB/SC/CURHTML/R1168.PDF
<br />TABLE 5.504.4.2 - SEALANT VOC LIMIT
<br />Less Water and Less Exempt Compounds in Grams per Liter
<br />SEALANTS CURRENT VOC LIMIT
<br />ARCHITECTURAL 250
<br />MARINE DECK 760
<br />NONMEMBRANE ROOF 300
<br />ROADWAY 250
<br />SINGLE-PLY ROOF MEMBRANE 450
<br />OTHER 420
<br />SEALANT PRIMERS
<br />ARCHITECTURAL
<br /> NONPOROUS 250
<br /> POROUS 775
<br />MODIFIED BITUMINOUS 500
<br />MARINE DECK 760
<br />OTHER 750
<br />NOTE: FOR ADDITIONAL INFORMATION REGARDING METHODS TO MEASURE THE VOC
<br />CONTENT SPECIFIED IN THESE TABLES, SEE SOUTH COAST AIR QUALITY MANAGEMENT
<br />DISTRICT RULE 1168.
<br />TABLE 5.504.4.3 - CONT.
<br />GRAMS OF VOC PER LITER OF COATING, LESS WATER & LESS EXEMPT COMPOUNDS
<br />COATING CATEGORY CURRENT VOC LIMIT
<br />SPECIALTY COATINGS
<br />ALUMINUM ROOF COATINGS 400
<br />BASEMENT SPECIALTY COATINGS 400
<br />BITUMINOUS ROOF COATINGS 50
<br />BITUMINOUS ROOF PRIMERS 350
<br />BOND BREAKERS 350
<br />CONCRETE CURING COMPOUNDS 350
<br />CONCRETE/MASONRY SEALERS 100
<br />DRIVEWAY SEALERS 50
<br />DRY FOG COATINGS 150
<br />FAUX FINISHING COATINGS 350
<br />FIRE RESISTIVE COATINGS 350
<br />FLOOR COATINGS 100
<br />FORM-RELEASE COMPOUNDS 250
<br />GRAPHIC ARTS COATINGS (SIGN PAINTS)500
<br />HIGH-TEMPERATURE COATINGS 420
<br />INDUSTRIAL MAINTENANCE COATINGS 250
<br />LOW SOLIDS COATINGS1 120
<br />MAGNESITE CEMENT COATINGS 450
<br />MASTIC TEXTURE COATINGS 100
<br />METALLIC PIGMENTED COATINGS 500
<br />MULTICOLOR COATINGS 250
<br />PRETREATMENT WASH PRIMERS 420
<br />PRIMERS, SEALERS, & UNDERCOATERS 100
<br />REACTIVE PENETRATING SEALERS 350
<br />RECYCLED COATINGS 250
<br />ROOF COATINGS 50
<br />RUST PREVENTATIVE COATINGS 250
<br />SHELLACS:
<br />CLEAR 730
<br />OPAQUE 550
<br />SPECIALTY PRIMERS, SEALERS & UNDERCOATERS 100
<br />STAINS 250
<br />STONE CONSOLIDANTS 450
<br />SWIMMING POOL COATINGS 340
<br />TRAFFIC MARKING COATINGS 100
<br />TUB & TILE REFINISH COATINGS 420
<br />WATERPROOFING MEMBRANES 250
<br />WOOD COATINGS 275
<br />WOOD PRESERVATIVES 350
<br />ZINC-RICH PRIMERS 340
<br />1. GRAMS OF VOC PER LITER OF COATING, INCLUDING WATER & EXEMPT COMPOUNDS
<br />2. THE SPECIFIED LIMITS REMAIN IN EFFECT UNLESS REVISED LIMITS ARE LISTED IN SUBSEQUENT COLUMNS IN
<br />THE TABLE.
<br />3. VALUES IN THIS TABLE ARE DERIVED FROM THOSE SPECIFIED BY THE CALIFORNIA AIR RESOURCES BOARD,
<br />ARCHITECTURAL COATINGS SUGGESTED CONTROL MEASURE, FEB. 1, 2008. MORE INFORMATION IS AVAILABLE
<br />FROM THE AIR RESOURCES BOARD.
<br />TABLE 5.504.4.5 - FORMALDEHYDE LIMITS1
<br />MAXIMUM FORMALDEHYDE EMISSIONS IN PARTS PER MILLION
<br />PRODUCT CURRENT LIMIT
<br />HARDWOOD PLYWOOD VENEER CORE 0.05
<br />HARDWOOD PLYWOOD COMPOSITE CORE 0.05
<br />PARTICLE BOARD 0.09
<br />MEDIUM DENSITY FIBERBOARD 0.11
<br />THIN MEDIUM DENSITY FIBERBOARD2 0.13
<br />1. VALUES IN THIS TABLE ARE DERIVED FROM THOSE SPECIFIED BY THE CALIFORNIA AIR RESOURCES BOARD, AIR
<br />TOXICS CONTROL MEASURE FOR COMPOSITE WOOD AS TESTED IN ACCORDANCE WITH ASTM E 1333. FOR
<br />ADDITIONAL INFORMATION, SEE CALIFORNIA CODE OF REGULATIONS, TITLE 17, SECTIONS 93120 THROUGH 93120.12.
<br />2. THIN MEDIUM DENSITY FIBERBOARD HAS A MAXIMUM THICKNESS OF 5/16 INCHES (8 MM).
<br />5.508.2 Supermarket refrigerant leak reduction. New commercial refrigeration systems shall comply with the
<br />provisions of this section when installed in retail food stores 8,000 square feet or more conditioned area, and that
<br />utilize either refrigerated display cases, or walk-in coolers or freezers connected to remote compressor units or
<br />condensing units. The leak reduction measures apply to refrigeration systems containing high-global-warming potential
<br />(high-GWP) refrigerants with a GWP of 150 or greater. New refrigeration systems include both new facilities and the
<br />replacement of existing refrigeration systems in existing facilities.
<br />Exception: Refrigeration systems containing low-global warming potential (low-GWP) refrigerant with a GWP
<br />value less than 150 are not subject to this section. Low-GWP refrigerants are nonozone-depleting refrigerants
<br />that include ammonia, carbon dioxide (CO2), and potentially other refrigerants.
<br />5.508.2.1 Refrigerant piping. Piping compliant with the California Mechanical Code shall be installed to be
<br />accessible for leak protection and repairs. Piping runs using threaded pipe, copper tubing with an outside
<br />diameter (OD) less than 1/4 inch, flared tubing connections and short radius elbows shall not be used in
<br />refrigerant systems except as noted below.
<br />5.508.2.1.1 Threaded pipe. Threaded connections are permitted at the compressor rack.
<br />5.508.2.1.2 Copper pipe. Copper tubing with an OD less than 1/4 inch may be used in systems with a
<br />refrigerant charge of 5 pounds or less.
<br />5.508.2.1.2.1 Anchorage. One-fouth-inch OD tubing shall be securely clamped to a rigid base to
<br />keep vibration levels below 8 mils.
<br />5.508.2.1.3 Flared tubing connections. Double-flared tubing connections may be used for pressure
<br />controls, valve pilot lines and oil.
<br />Exception: Single-flared tubing connections may be used with a multiring seal coated with
<br />industrial sealant suitable for use with refrigerants and tightened in accordance with manufacturer's
<br />recommendations.
<br />5.508.2.1.4 Elbows. Short radius elbows are only permitted where space limitations prohibit use of
<br />long radius elbows.
<br />5.508.2.2 Valves. Valves Valves and fittings shall comply with the California Mechanical Code and as
<br />follows.
<br />5.508.2.2.1 Pressure relief valves. For vessels containing high-GWP refrigerant, a rupture disc shall
<br />be installed between the outlet of the vessel and the inlet of the pressure relief valve.
<br />5.508.2.2.1.1 Pressure detection. A pressure gauge, pressure transducer or other device shall
<br />be installed in the space between the rupture disc and the relief valve inlet to indicate a disc
<br />rupture or discharge of the relief valve.
<br />5.508.2.2.2 Access valves. Only Schrader access valves with a brass or steel body are
<br />permitted for use.
<br />5.508.2.2.2.1 Valve caps. For systems with a refrigerant charge of 5 pounds or more, valve caps
<br />shall be brass or steel and not plastic.
<br />5.508.2.2.2.2 Seal caps. If designed for it, the cap shall have a neoprene O-ring in place.
<br />5.508.2.2.2.2.1 Chain tethers. Chain tethers to fit ovr the stem are required for valves
<br />designed to have seal caps.
<br />Exception: Valves with seal caps that are not removed from the valve during stem
<br />operation.
<br />5.508.2.3 Refrigerated service cases. Refrigerated service cases holding food products containing vinegar and
<br />salt shall have evaporator coils of corrosion-resistant material, such as stainless steel; or be coated to prevent
<br />corrosion from these substances.
<br />5.508.2.3.1 Coil coating. Consideration shall be given to the heat transfer efficiency of coil coating to
<br />maximize energy efficiency.
<br />5.508.2.4 Refrigerant receivers. Refrigerant receivers with capacities greater than 200 pounds shall be fitted
<br />with a device tha indicates the level of refrigerant in the receiver.
<br />5.508.2.5 Pressure testing. The system shall be pressure tested during installation prior to evacuation and
<br />charging.
<br />5.508.2.5.1 Minimum pressure. The system shall be charged with regulated dry nitrogen and
<br />appropriate tracer gas to bring system pressure up to 300 psig minimum.
<br />5.508.2.5.2 Leaks. Check the system for leaks, repair any leaks, and retest for pressure using the same
<br />gauge.
<br />5.508.2.5.3 Allowable pressure change. The system shall stand, unaltered, for 24 hours with no more
<br />than a +/- one pound pressure change from 300 psig, measured with the same gauge.
<br />5.508.2.6 Evacuation. The system shall be evacuated after pressure testing and prior to charging.
<br />5.508.2.6.1 First vacuum. Pull a system vacuum down to at least 1000 microns (+/- 50 microns), and
<br />hold for 30 minutes.
<br />5.508.2.6.2 Second vacuum. Pull a second system vacuum to a minimum of 500 microns and hold for 30
<br />minutes.
<br />5.508.2.6.3 Third vacuum. Pull a third vacuum down to a minimum of 300 microns, and hold for 24 hours
<br />with a maximum drift of 100 microns over a 24-hour period.
<br />CHAPTER 7
<br />INSTALLER & SPECIAL INSPECTOR QUALIFICATIONS
<br />702 QUALIFICATIONS
<br />702.1 INSTALLER TRAINING. HVAC system installers shall be trained and certified in the proper
<br />installation of HVAC systems including ducts and equipment by a nationally or regionally recognized training or
<br />certification program. Uncertified persons may perform HVAC installations when under the direct supervision and
<br />responsibility of a person trained and certified to install HVAC systems or contractor licensed to install HVAC systems.
<br />Examples of acceptable HVAC training and certification programs include but are not limited to the following:
<br />1. State certified apprenticeship programs.
<br />2. Public utility training programs.
<br />3. Training programs sponsored by trade, labor or statewide energy consulting or verification organizations.
<br />4. Programs sponsored by manufacturing organizations.
<br />5. Other programs acceptable to the enforcing agency.
<br />702.2 SPECIAL INSPECTION [HCD]. When required by the enforcing agency, the owner or the
<br />responsible entity acting as the owner's agent shall employ one or more special inspectors to provide inspection or
<br />other duties necessary to substantiate compliance with this code. Special inspectors shall demonstrate competence
<br />to the satisfaction of the enforcing agency for the particular type of inspection or task to be performed. In addition to
<br />other certifications or qualifications acceptable to the enforcing agency, the following certifications or education may be
<br />considered by the enforcing agency when evaluating the qualifications of a special inspector:
<br />1. Certification by a national or regional green building program or standard publisher.
<br />2. Certification by a statewide energy consulting or verification organization, such as HERS raters, building
<br /> performance contractors, and home energy auditors.
<br />3. Successful completion of a third party apprentice training program in the appropriate trade.
<br />4. Other programs acceptable to the enforcing agency.
<br />Notes:
<br />1. Special inspectors shall be independent entities with no financial interest in the materials or the
<br />project they are inspecting for compliance with this code.
<br />2. HERS raters are special inspectors certified by the California Energy Commission (CEC) to rate
<br />homes in California according to the Home Energy Rating System (HERS).
<br />[BSC-CG] When required by the enforcing agency, the owner or the responsible entity acting as the owner's agent
<br />shall employ one or more special inspectors to provide inspection or other duties necessary to substantiate
<br />compliance with this code. Special inspectors shall demonstrate competence to the satisfaction of the enforcing
<br />agency for the particular type of inspection or task to be performed. In addition, the special inspector shall have a
<br />certification from a recognized state, national or international association, as determined by the local agency. The
<br />area of certification shall be closely related to the primary job function, as determined by the local agency.
<br />Note: Special inspectors shall be independent entities with no financial interest in the materials or the
<br />project they are inspecting for compliance with this code.
<br />703 VERIFICATIONS
<br />703.1 DOCUMENTATION. Documentation used to show compliance with this code shall include but is not limited to,
<br />construction documents, plans, specifications, builder or installer certification, inspection reports, or other methods
<br />acceptable to the enforcing agency which demonstrate substantial conformance. When specific documentation or
<br />special inspection is necessary to verify compliance, that method of compliance will be specified in the appropriate
<br />section or identified applicable checklist.
<br />2022 CALIFORNIA GREEN BUILDING STANDARDS CODE
<br />NONRESIDENTIAL MANDATORY MEASURES, SHEET 3 (January 2023)
<br />SECTION 5.505 INDOOR MOISTURE CONTROL
<br />5.505.1 INDOOR MOISTURE CONTROL. Buildings shall meet or exceed the provisions of California Building Code,
<br />CCR, Title 24, Part 2, Sections 1202 (Ventilation) and Chapter 14 (Exterior Walls). For additional measures, see
<br />Section 5.407.2 of this code.
<br />SECTION 5.506 INDOOR AIR QUALITY
<br />5.506.1 OUTSIDE AIR DELIVERY. For mechanically or naturally ventilated spaces in buildings, meet the minimum
<br />requirements of Section 120.1 (Requirements For Ventilation) of the California Energy Code, or the applicable local
<br />code, whichever is more stringent, and Division 1, Chapter 4 of CCR, Title 8.
<br />5.506.2 CARBON DIOXIDE (CO2) MONITORING. For buildings or additions equipped with demand control
<br />ventilation, CO2 sensors and ventilation controls shall be specified and installed in accordance with the requirements
<br />of the California Energy Code, Section 120(c)(4).
<br />5.506.3 Carbon dioxide (CO2) monitoring in classrooms.
<br />(DSA-SS) Each public K-12 school classroom, as listed in Table 120.1-A of the California Energy Code, shall be
<br />equipped with a carbon dioxide monitor or sensor that meets the following requirements:
<br />1. The monitor or sensor shall be permanently affixed in a tamper-proof manner in each classroom between 3 and
<br />6 feet (914 mm and 1829 mm) above the floor and at least 5 feet (1524 mm) away from door and operable
<br />windows.
<br />2. When the monitor or sensor is not integral to an Energy Management Control System (EMCS), the monitor or
<br />sensor shall display the carbon dioxide readings on the device. When the sensor is integral to an EMCS, the
<br />carbon dioxide readings shall be available to and regularly monitored by facility personnel.
<br />3. A monitor shall provide notification though a visual indicator on the monitor when the carbon dioxide levels in the
<br />classroom have exceeded 1,100ppm. A sensor integral to an EMCS shall provide notification to facility
<br />personnel through a visual and/or audible indicator when the carbon dioxide levels in the classroom have
<br />exceeded 1,100ppm.
<br />4. The monitor or sensor shall measure carbon dioxide levels at minimum 15- minute intervals and shall maintain a
<br />record of previous carbon dioxide measurements of not less than 30 days duration.
<br />5. The monitor or sensor used to measure carbon dioxide levels shall have the capacity to measure carbon dioxide
<br />levels with a range of 400ppm to 2000ppm or greater.
<br />6. The monitor or sensor shall be certified by the manufacturer to be accurate within 75ppm at 1,000ppm carbon
<br />dioxide concentration and shall be certified by the manufacturer to require calibration no more frequently than
<br />once every 5 years.
<br />SECTION 5.507 ENVIRONMENTAL COMFORT
<br />5.507.4 ACOUSTICAL CONTROL. Employ building assemblies and components with Sound Transmission Class
<br />(STC) values determined in accordance with ASTM E 90 and ASTM E 413, or Outdoor-Indoor Sound Transmission
<br />Class (OITC) determined in accordance with ASTM E 1332, using either the prescriptive or performance method in
<br />Section 5.507.4.1 or 5.507.4.2.
<br />Exception: Buildings with few or no occupants or where occupants are not likely to be affected by exterior
<br />noise, as determined by the enforcement authority, such as factories, stadiums, storage, enclosed parking
<br />structures and utility buildings.
<br />Exception: [DSA-SS] For public schools and community colleges, the requirements of this section and all
<br />subsections apply only to new construction.
<br />5.507.4.1 Exterior noise transmission, prescriptive method. Wall and roof-ceiling assemblies exposed to
<br />the noise source making up the building or addition envelope or altered envelope shall meet a composite STC
<br />rating of at least 50 or a composite OITC rating of no less than 40, with exterior windows of a minimum STC of
<br />40 or OITC of 30 in the following locations:
<br />1. Within the 65 CNEL noise contour of an airport.
<br />Exceptions:
<br />1. Ldn or CNEL for military airports shall be determined by the facility Air Installation Compatible
<br /> Land Use Zone (AICUZ) plan.
<br />2. Ldn or CNEL for other airports and heliports for which a land use plan has not been developed
<br /> shall be determined by the local general plan noise element.
<br />2. Within the 65 CNEL or Ldn noise contour of a freeway or expressway, railroad, industrial source or
<br /> fixed-guideway source as determined by the Noise Element of the General Plan.
<br />5.507.4.1.1. Noise exposure where noise contours are not readily available. Buildings exposed to a
<br />noise level of 65 dB Leq - 1-hr during any hour of operation shall have building, addition or alteration
<br />exterior wall and roof-ceiling assemblies exposed to the noise source meeting a composite STC rating of
<br />at least 45 (or OITC 35), with exterior windows of a minimum STC of 40 (or OITC 30).
<br />5.507.4.2 Performance Method. For buildings located as defined in Section 5.507.4.1 or 5.507.4.1.1, wall and
<br />roof-ceiling assemblies exposed to the noise source making up the building or addition envelope or altered
<br />envelope shall be constructed to provide an interior noise environment attributable to exterior sources that does
<br />not exceed an hourly equivalent noise level (Leq-1Hr) of 50 dBA in occupied areas during any hour of operation.
<br />5.507.4.2.1 Site Features. Exterior features such as sound walls or earth berms may be utilized as
<br />appropriate to the building, addition or alteration project to mitigate sound migration to the interior.
<br />5.507.4.2.2 Documentation of Compliance. An acoustical analysis documenting complying interior
<br />soundlevels shall be prepared by personnel approved by the architect or engineer of record.
<br />5.507.4.3 Interior sound transmission. Wall and floor-ceiling assemblies separating tenant spaces and tenant
<br />spaces and public places shall have an STC of at least 40.
<br />Note: Examples of assemblies and their various STC ratings may be found at the California Office of
<br />Noise Control: www.toolbase.org/PDF/CaseStudies/stc_icc_ratings.pdf.
<br />SECTION 5.508 OUTDOOR AIR QUALITY
<br />5.508.1 Ozone depletion and greenhouse gas reductions. Installations of HVAC, refrigeration and fire suppression
<br />equipment shall comply with Sections 5.508.1.1 and 5.508.1.2.
<br />5.508.1.1 Chlorofluorocarbons (CFCs). Install HVAC, refrigeration and fire suppression equipment that do not
<br />contain CFCs.
<br />5.508.1.2 Halons. Install HVAC, refrigeration and fire suppression equipment that do not contain Halons.
<br />5.504.4.6 Resilient flooring systems. Where resilient flooring is installed, at least 80 percent of floor area
<br />receiving resilient flooring shall meet the requirements of the California Department of Public Health,"Standard
<br />Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using
<br />Environmental Chambers," Version 1.2, January 2017 (Emission testing method for California Specifications
<br />01350)
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />https://www.cdph.ca.gov/Programs/CCDPHP/DEODC/EHLB/IAQ/Pages/VOC.aspx#material
<br />5.504.4.6.1 Verification of compliance. Documentation shall be provided verifying that resilient flooring
<br />materials meet the pollutant emission limits.
<br />5.504.4.7 Thermal insulation
<br />Comply with the requirements of the California Department of Public Health, "Standard Method of the Testing
<br />and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers,
<br />"Version 1.2, January 1.2, January 2017 (Emission testing method for California Specification 01350).
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />https://www.cdph.ca.gov/Programs/CCDPHP/DEODC/EHLB/IAQ/Pages/VOC.aspx#material
<br />5.504.4.7.1 Verification of compliance.
<br />Documentation shall be provided verifying that thermal insulation materials meet the pollutant emission
<br />limits.
<br />5.504.4.8 Acoustical ceiling and wall panels.
<br />Comply with the requirements of the California Department of Public Health, "Standard Method for the Testing
<br />and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers, "
<br />Version 1.2, January 2017 (Emission testing method for California Specification 01350).
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />5.504.4.8.1 Verification of compliance. Documentation shall be provided verifying that acoustical
<br /> finish materials meet the pollutant emission limits.
<br />5.504.5.3 Filters. In mechanically ventilated buildings, provide regularly occupied areas of the building with air
<br />filtration media for outside and return air that provides at least a Minimum Efficiency Reporting Value (MERV) of
<br />13. MERV 13 filters shall be installed prior to occupancy, and recommendations for maintenance with filters of
<br />the same value shall be included in the operation and maintenance manual.
<br />Exceptions: Existing mechanical equipment.
<br /> 5.504.5.3.1 Labeling. Installed filters shall be clearly labeled by the manufacturer indicating the MERV
<br /> rating.
<br />5.504.7 ENVIRONMENTAL TOBACCO SMOKE (ETS) CONTROL. Where outdoor areas are provided for smoking,
<br />prohibit smoking within 25 feet of building entries, outdoor air intakes and operable windows and within the building as
<br />already prohibited by other laws or regulations; or as enforced by ordinances, regulations or policies of any city,
<br />county, city and county, California Community College, campus of the California State University, or campus of the
<br />University of California, whichever are more stringent. When ordinances, regulations or policies are not in place, post
<br />signage to inform building occupants of the prohibitions.
<br />5.504.4.3.2 Verification. Verification of compliance with this section shall be provided at the request of
<br />the enforcing agency. Documentation may include, but is not limited to, the following:
<br />1. Manufacturer's product specification
<br />2. Field verification of on-site product containers
<br />5.504.4.4 Carpet Systems.
<br />All carpet installed in the building interior shall meet the requirements of the California Department of Public
<br />Health, "Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor
<br />Sources Using Environmental Chambers." Version 1.2, January 2017 (Emission testing method for California
<br />Specifications 01350).
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />https://www.cdph.ca.gov/Programs/CCDPHP/DEODC/EHLB/IAQ/Pages/VOC.aspx#material
<br />5.504.4 FINISH MATERIAL POLLUTANT CONTROL. Finish materials shall comply with Sections 5.504.4.1 through
<br />5.504.4.6.
<br />5.504.4.1 Adhesives, sealants and caulks. Adhesives, sealants, and caulks used on the project shall meet
<br />the requirements of the following standards:
<br />1. Adhesives, adhesive bonding primers, adhesive primers, sealants, sealant primers and caulks shall
<br />comply with local or regional air pollution control or air quality management district rules where
<br />applicable, or SCAQMD Rule 1168 VOC limits, as shown in Tables 5.504.4.1 and 5.504.4.2. Such
<br />products also shall comply with the Rule 1168 prohibition on the use of certain toxic compounds
<br />(chloroform, ethylene dichloride, methylene chloride, perchloroethylene and trichloroethylene), except for
<br />aerosol products as specified in subsection 2, below.
<br />2. Aerosol adhesives, and smaller unit sizes of adhesives, and sealant or caulking compounds (in
<br />units of product, less packaging, which do not weigh more than one pound and do not consist of more
<br />than 16 fluid ounces) shall comply with statewide VOC standards and other requirements, including
<br />prohibitions on use of certain toxic compounds, of California Code of Regulations, Title 17, commencing
<br />with Section 94507.
<br />Y N/A Y N/A Y N/A Y N/ARESPON.
<br />PARTY
<br />RESPON.
<br />PARTY
<br />RESPON.
<br />PARTY
<br />RESPON.
<br />PARTY
<br />Y = YES
<br />N/A = NOT APPLICABLE
<br />RESPON. PARTY = RESPONSIBLE PARTY (ie: ARCHITECT, ENGINEER,
<br />OWNER, CONTRACTOR, INSPECTOR ETC.)
<br />De
<br />s
<br />i
<br />g
<br />n
<br />10
<br />4
<br />9
<br />2
<br />
<br />T
<br />R
<br />A
<br />S
<br />K
<br />
<br />A
<br />V
<br />E
<br />,
<br />
<br />#
<br />B
<br />Ga
<br />r
<br />d
<br />e
<br />n
<br />
<br />G
<br />r
<br />o
<br />v
<br />e
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />8
<br />4
<br />3
<br />Ph
<br />o
<br />n
<br />e
<br />:
<br />
<br />(
<br />7
<br />1
<br />4
<br />)
<br />4
<br />1
<br />7
<br />-
<br />1
<br />8
<br />3
<br />9
<br />
<br />-
<br />
<br />(
<br />6
<br />5
<br />7
<br />)
<br />7
<br />2
<br />0
<br />-
<br />8
<br />5
<br />5
<br />5
<br />Em
<br />a
<br />i
<br />l
<br />:
<br />
<br />k
<br />i
<br />m
<br />k
<br />h
<br />u
<br />e
<br />.
<br />n
<br />g
<br />u
<br />y
<br />e
<br />n
<br />2
<br />0
<br />1
<br />8
<br />@
<br />g
<br />m
<br />a
<br />i
<br />l
<br />.
<br />c
<br />o
<br />m
<br />CALGREEN CHECKLIST
<br />37
<br />5
<br />1
<br />
<br />S
<br />.
<br />
<br />H
<br />A
<br />R
<br />B
<br />O
<br />R
<br />
<br />B
<br />L
<br />V
<br />D
<br />.
<br />
<br />S
<br />U
<br />I
<br />T
<br />E
<br />
<br />#
<br />F
<br />,
<br />
<br />S
<br />A
<br />N
<br />T
<br />A
<br />
<br />A
<br />N
<br />A
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />4
<br />LE
<br />G
<br />A
<br />L
<br />I
<br />Z
<br />E
<br />
<br />R
<br />E
<br />M
<br />O
<br />D
<br />E
<br />L
<br />I
<br />N
<br />G
<br />
<br />W
<br />O
<br />R
<br />K
<br />NE
<br />W
<br />
<br />W
<br />A
<br />L
<br />K
<br />-
<br />I
<br />N
<br />
<br />F
<br />R
<br />E
<br />E
<br />Z
<br />E
<br />R
<br />
<br />&
<br />
<br />N
<br />E
<br />W
<br />
<br />2
<br />N
<br />D
<br />
<br />F
<br />R
<br />O
<br />N
<br />T
<br />
<br />C
<br />O
<br />U
<br />N
<br />T
<br />E
<br />R
<br />
<br />S
<br />E
<br />R
<br />V
<br />I
<br />C
<br />E
<br />3751 S Harbor Blvd Unit#
<br />F1/30/2025
|