|
Wa
<br />s
<br />h
<br />e
<br />r
<br />Dr
<br />y
<br />e
<br />r
<br />REF.
<br />DW
<br />280 CFM Vent
<br />Hood
<br />Min. 50 CFM W/Humidity sensor
<br />exhaust fan W/Min. 5 air changes
<br />per hour.
<br />Fans shall be Energy Star compliant
<br />and be ducted to terminate outside
<br />of the building.
<br />SYMBOLS:
<br />Smoke & Carbon Monoxide
<br />Combination Detector
<br />S/C
<br />Hard wired Smoke Detector
<br />W/backup battery
<br />SD
<br />Hard wired Carbon MonoxideCM
<br />Recessed Can Lights (LED Lights)
<br />Outlet (AFCI)
<br />Outlet GFCI (Ground Fault Circuit
<br />Interrupter)GFCI
<br />Outlet GFCI (Ground Fault Circuit
<br />Interrupter) / WaterproofGFCI
<br />WP
<br />Outlet - Cable / TV /Phone
<br />Switch
<br />Switch W/Occupancy SensorOS
<br />ATTIC VENTILATION CALCULATIONS
<br />ATTIC VENTILATION SHALL NOT BE LESS THAN 1/150
<br />OF THE AREA OF THE SPACE VENTILATED.
<br />TOTAL ROOF AREA VENTILATION AREA REQ.
<br />500 SQ FT 3.5 SQ FT
<br />VENT SIZE & AREA TOTAL No. OF VENTS -> VNET AREA
<br />24" x 12" Dormer = .7 SQ FT 5 VENTS @ .7 SQ FT
<br />REQUIRED < PROVIDED
<br />3.5 SQ FT < 3.5 SQ FT
<br />DORMER
<br />VENT
<br />DORMER
<br />VENT
<br />DORMER
<br />VENT
<br />Roofing Material Type
<br />Class "A" Shingles per
<br />ICC # ESR-1745
<br />To match existing
<br />DORMER
<br />VENT
<br />DORMER
<br />VENT
<br />(N
<br />)
<br />
<br />3
<br />
<br />:
<br />1
<br />2
<br />(N
<br />)
<br />
<br />3
<br />
<br />:
<br />1
<br />2
<br />(E) 4 :12
<br />(E
<br />)
<br />
<br />4
<br />
<br />:
<br />1
<br />2
<br />(E
<br />)
<br />
<br />4
<br />
<br />:
<br />1
<br />2
<br />1' - 0"
<br />1'
<br />
<br />-
<br />
<br />0
<br />"
<br />7' - 6"
<br />16' - 10 1/2"
<br />23
<br />'
<br />
<br />-
<br />
<br />0
<br />"
<br />1'
<br />
<br />-
<br />
<br />0
<br />"
<br />19' - 0"
<br />5
<br />A2
<br />6
<br />A2
<br />EX
<br />I
<br />S
<br />T
<br />I
<br />N
<br />G
<br />
<br />E
<br />A
<br />V
<br />E
<br />
<br />T
<br />O
<br />
<br />B
<br />E
<br />
<br />D
<br />E
<br />M
<br />O
<br />L
<br />I
<br />S
<br />H
<br />E
<br />D
<br />1
<br />H
<br />O
<br />U
<br />R
<br />
<br />F
<br />I
<br />R
<br />E
<br />
<br />R
<br />A
<br />T
<br />E
<br />D
<br />
<br />E
<br />A
<br />V
<br />E
<br />
<br />P
<br />E
<br />R
<br />
<br />D
<br />E
<br />T
<br />A
<br />I
<br />L
<br />
<br />(
<br />I
<br />F
<br />
<br />A
<br />P
<br />P
<br />L
<br />I
<br />C
<br />A
<br />B
<br />L
<br />E
<br />)
<br />GFCI
<br />WP
<br />Linen
<br />GF
<br />C
<br />I
<br />WP
<br />GF
<br />C
<br />I
<br />WP
<br />GF
<br />C
<br />I
<br />WP
<br />GFCI
<br />WP
<br />GFCI
<br />WP
<br />GFCI
<br />WP
<br />SHEET TITLE:
<br />SCALE:
<br />SHEET NO.
<br />PR
<br />O
<br />J
<br />E
<br />C
<br />T
<br />DA
<br />T
<br />E
<br />RE
<br />V
<br />I
<br />S
<br />I
<br />O
<br />N
<br />PROJECT NUMBER:
<br />OWNER / CLIENT:
<br />DATE ISSUED:
<br />DATE SUBMITTED:
<br />DRAWN BY:
<br />CHECKED BY:
<br />THESE DRAWINGS ARE THE PROPERTY
<br />OF TREEIUM INC AND SHALL NOT BE
<br />USED ON ANY OTHER WORK EXCEPT
<br />BY AGREEMENT WITH TREEIUM INC
<br />48
<br />2
<br />1
<br />
<br />L
<br />A
<br />N
<br />K
<br />E
<br />R
<br />S
<br />H
<br />I
<br />M
<br />
<br />B
<br />L
<br />V
<br />D
<br />
<br />S
<br />T
<br />E
<br />
<br />F
<br />
<br />#
<br />4
<br />4
<br />5
<br />
<br />NO
<br />R
<br />T
<br />H
<br />
<br />H
<br />O
<br />L
<br />L
<br />Y
<br />W
<br />O
<br />O
<br />D
<br />,
<br />
<br />C
<br />A
<br />31
<br />0
<br />.
<br />6
<br />9
<br />4
<br />.
<br />0
<br />8
<br />3
<br />5
<br />WW
<br />W
<br />.
<br />A
<br />V
<br />D
<br />E
<br />S
<br />I
<br />G
<br />N
<br />.
<br />L
<br />A
<br />AV
<br />
<br />D
<br />E
<br />S
<br />I
<br />G
<br />N
<br />As indicated
<br />AVD24D019
<br />Debbini, Lubna
<br />Roof +
<br />Electrical Plan
<br />A3
<br />To
<br />w
<br />n
<br />e
<br />r
<br />
<br />A
<br />D
<br />U
<br />11
<br />0
<br />8
<br />
<br />N
<br />
<br />T
<br />o
<br />w
<br />n
<br />e
<br />r
<br />
<br />S
<br />t
<br />
<br />&
<br />
<br />1
<br />1
<br />0
<br />8
<br />
<br />N
<br />To
<br />w
<br />n
<br />e
<br />r
<br />
<br />S
<br />t
<br />r
<br />e
<br />e
<br />t
<br />
<br />#
<br />2
<br />Sa
<br />n
<br />t
<br />a
<br />
<br />A
<br />n
<br />a
<br />,
<br />
<br />C
<br />A
<br />
<br />9
<br />2
<br />7
<br />0
<br />3
<br />ER/CB
<br />Checker
<br />---
<br />A. PANEL LOCATIONS
<br />PANELS SHALL NOT BE LOCATED IN THE VICINITY OF EASILY GINITABLE MATERIAL, SUCH AS CLOTHES CLOSETS, OR IN
<br />BATHROOMS [CEC 240-24(D)]
<br />B.NON-METALLIC SHEATHED CABLE [CEC 334]
<br />NON-METALLIC SHEATHED CABLE SHALL BE:
<br />1. PROTECTED BY RIGID METAL CONDUIT, ELECTRICAL METALLIC, TUBING SCHEDULE 80 PVC CONDUIT, PIPE OR OTHER
<br />MEANS WHEN CABLE IS EXPOSED OR SUBJECT TO PHYSICAL DAMAGE. [CEC 334.15(B)]
<br />2. PROTECTED BY A 1/16” STEEL PLATE OR SLEEVE OR BE NOT LESS THAN 1-1/4" FROM THE NEAREST EDGE OF THE
<br />FRAMING MEMBER, WHEN INSTALLED THROUGH FRAMING MEMBERS. STEEL PLATES ARE SLEEVES ARE REQUIRED ON ALL
<br />DOUBLE SHEAR WALLS WHEN CABLE IS INSTALLED EITHER THROUGH PARALLEL TO FRAMING MEMBERS [CEC 334.17]
<br />3.PROTECTED BY GUARD STRIPS WITHIN 6 FEET OF AN ATTIC ACCESS WHEN NO PERMANENT STAIRS OR LADDERS ARE
<br />PROVIDED [CEC 334.23, 320.23]
<br />4.PROTECTED BY GUARD STRIPS IN THE ENTIRE ATTIC WHEN PERMANENT STAIRS OR LADDER ARE PROVIDED. ACCESS
<br />PANELS OR DOOR FROM THE SECOND FLOOR INTO THE ATTIC ARE CONSIDERED PERMANENT ACCESS AND GUARD STRIPS
<br />ARE REQUIRED IN THE ENTIRE ATTIC.
<br />5. HAVING A BENDING RADIUS NOT LESS THAN 5 TIMES THE DIAMETER OF THE CABLE [CEC 334.24]
<br />6. SUPPORTED AT INTERVALS NOT EXCEEDING 4-1/2 FEET AND WITHIN 12 ” OF EVERY OUTLET BOX, JUNCTION BOX, CABINET
<br />OR FITTING [CEC 334.30]
<br />C.CIRCUITS AND RECEPTACLES
<br />1. TAMPER-RESISTANT RECEPTACLES SHALL BE INSTALLED AS SPECIFIED IN DWELLING UNITS IN ALL AREAS SPECIFIED
<br />IN 210.52 [CEC 406.12]
<br />2.RECEPTACLES SHALL BE INSTALLED SO THAT NO POINT ALONG THE FLOOR LINE IN ANY WALL SPACES IS MORE THAN
<br />6 FT FROM AN OUTLET, INCLUDING ANY WALL SPACE 2FT WIDE OR GREATER. NOTE: A FIXED PANEL OF SLIDING GLASS DOOR
<br />IS CONSIDERED WALL SPACE. [CEC 210.52(A)].
<br />3. IN KITCHENS, BREAKFAST ROOMS, PANTRIES AND DINING ROOMS A MINIMUM OF 2-20A CIRCUITS SHALL BE PROVIDED
<br />[CEC 210.11(C)(1)]. COUNTER SPACE RECEPTACLES SHALL BE GFCI [CEC 210.8(A)] AND INSTALLED:
<br />3.1.AT EACH WALL COUNTER SPACE THAT IS 12IN. OR GREATER [CEC 210.52(C)(1)]
<br />3.2.NO MORE THAN 48IN. O.C. [CEC 210.52(C)(1)]
<br />3.3.MAXIMUM 24IN. FROM THE END OF THE SURFACE [CEC 210.52(C)(1)]
<br />3.4.MAXIMUM 20IN. ABOVE COUNTER SURFACE [CEC 210.52(C)(5)]
<br />3.5.ON ISLAND COUNTER SPACES (ONE RECEPTACLE MIN) NOT MORE THAN 12IN. BELOW COUNTER SURFACE
<br />[CEC 210.52(C)(5) EXEMPTION]. AN ISLAND WITH LESS THAN 12IN BEHIND A RANGE TOP OF SINK IS CONSIDERED AS DIVING
<br />THE COUNTERTOP INTO TWO SEPARATE SPACES [CEC 210.52(C)(2)]
<br />3.6.ON PENINSULAR COUNTER SPACES (ONE RECEPTACLE MIN) NOT MORE THAN 12IN. BELOW COUNTER
<br />SURFACE [CEC 210.52 (C)(5) EXCEPTION]
<br />4.BATHROOMS SHALL HAVE A SEPARATE 20A CIRCUIT [CEC 210.11(C)(3)] WITH AT LEAST ONE GFCI WALL RECEPTACLES
<br />WITHIN 36IN OF EACH BASIN [CEC 210.8(A)(1); CEC 210.52(D)]
<br />5.LAUNDRY ROOMS SHALL HAVE A SEPARATE 20A CIRCUIT WITH AT LEAST ONE RECEPTACLE SHALL BE PROVIDED [CEC
<br />201.11(C)(2)]. ALL RECEPTACLES WITHIN 6 FT. OF THE SINK SHALL BE GFCI
<br />6.IN GARAGES, AT LEAST ONE GFCI RECEPTACLE SHALL BE PROVIDED [CEC 210.52(G)]. ALL OTHER GARAGE
<br />RECEPTACLES EXCEPT THOSE DEDICATED TO AN APPLIANCE OR THAT ARE NOT READILY ACCESSIBLE SHALL BE GFCI [CEC
<br />210.8(A)(2)]
<br />7.IN HALLWAYS OF 10 FT. OR MORE IN LENGTH, AT LEAST ONE RECEPTACLE SHALL BE PROVIDED [CEC 210.8(A)(7)]
<br />8.OUTDOOR OUTLETS SHALL BE GFCI [CEC 210.8(A)(3)]. ONE OUTLET SHALL BE INSTALLED AT THE FRONT OF THE
<br />DWELLING AND ONE AT THE REAR OF THE DWELLING. RECEPTACLES SHALL BE ACCESSIBLE AT GRADE LEVEL AND NOT
<br />MORE THAN 6-1/2 FT. ABOVE GRADE [CEC 210.52(E)]
<br />9.ALL CRAWL SPACE RECEPTACLES SHALL BE GFCI [CEC 210.8(A)(4)]
<br />10.ALL INFINISHED BASEMENT RECEPTACLES SHALL BE GFCI [CEC 210.8(A)(5)] OR ARE SERVICE A DEDICATED
<br />APPLIANCES [CEC 210.8(A)(5)]
<br />11. ALL RECEPTACLES WITHIN 6 FT. OF A WET BAR SHALL BE GFCI [CEC 210.8(A)(7)]
<br />12.ALL RECEPTACLES ON 15A OR 20A BRANCH CIRCUITS THAT SUPPLY FAMILY ROOMS, DINING ROOMS, LIVING ROOMS,
<br />PARLORS, LABRARIES, DENS, BEDROOMS, SUNROOMS, RECREATION ROOMS, CLOSETS HALLWAYS OR SIMILAR ROOMS OR
<br />AREAS SHALL BE PROTECTED BY COMBINATION-TYPE-ARC-FAULT CIRCUIT INTERRUPTERS (AFCI), INCLUDING SWITCHED
<br />OUTLETS [CEC 210.12(A)]
<br />13.ALL RECEPTACLES SERVING APPLIANCES OR MOTORS WITH A RATING OF 1 HP OR 6 AMPS SHALL BE ON A SEPARATE
<br />CIRCUIT.
<br />14.FOR HVAC EQUIPMENT, A SEPARATE 15A OR 20A CIRCUIT WITH AN ACCESSIBLE RECEPTACLE AT THE EQUIPMENT
<br />SHALL BE PROVIDED WITHIN 25 FT OF THE EQUIPMENT [CEC 210.63]. IF LOCATED IN AN UNDER-FLOOR AEA, THE RECEPTACLE
<br />SHALL BE GFCI [CEC 210.8(4)]
<br />15. BASEMENT, GARAGES AND ACCESSORY BUILDINGS. FOR ONE-FAMILY DWELLING, AT LEAST ONE RECEPTACLE OUTLET
<br />SHALL BE INSTALLED IN THE AREAS SPECIFIED IN 210.2(G)(1) THROUGH (3)/ THESE RECEPTACLES SHALL BE IN ADDITION TO
<br />RECEPTACLES REQUIRED FOR SPECIFIC EQUIPMENT.
<br />15.1.GARAGES. IN EACH ATTACHED GARAGE AND IN EACH DETACHED GARAGE WITH ELECTRICAL POWER THE
<br />BRANCH CIRCUIT SUPPLYING THIS RECEPTACLE(S) SHALL NOT SUPPLY OUTLETS OF SIDE OF THE GARAGE. AT LEAST ONE
<br />RECEPTACLE OUTLET SHALL BE INSTALLED FOR EACH CAR SPACE.
<br />15.2.ACCESSORY BUILDINGS. IN EACH ACCESSORY BUILDING WITH ELECTRICAL POWER.
<br />15.3.BASEMENT. IN EACH SEPARATE UNFINISHED PORTION OF A BASEMENT.
<br />D.LIGHTING [CEC 210.70]
<br />1.SWITCHED LIGHTING SHALL BE INSTALLED IN:
<br />1.1 ALL HABITABLE ROOMS, BATHROOMS, HALLWAYS, AND STAIRWAYS AT EACH LEVEL.
<br />1.2 GARAGES.
<br />1.3 AT ALL OUTDOOR ENTRANCES AND EXITS.
<br />1.4 IN ALL ATTICS, UNDER FLOOR AREAS, UTILITY ROOMS AND BASEMENTS USED FOR STORAGE.
<br />1.5 NEAR HVAC EQUIPMENT IN ATTIC, UNDER FLOOR AREAS, ROOMS OR BASEMENTS, WITH A SWITCH AT THE
<br />ACCESS POINT.
<br />2.LIGHTING INSTALLED IN A CLOSET SHALL BE A SURFACE MOUNTED OR RECESSED FLUORESCENT FIXTURE OR
<br />A SURFACE MOUNTED INCANDESCENT FIXTURE WITH COMPLETELY ENCLOSED LAMPS OR RECESSED INCANDESCENT
<br />FIXTURE WITH COMPLETELY ENCLOSED LAMPS. SURFACE INCANDESCENT LIGHTING SHALL BE INSTALLED A MINIMUM OF
<br />12IN. FROM THE NEAREST POINT OF A STORAGE SPACE. SURFACE FLUORESCENT LIGHTING AND RECESSED LIGHTING SHALL
<br />BE INSTALLED A MINIMUM OF 6 IN. FROM THE NEAREST POINT OF A STORAGE SPACE [CEC 410.16(C)]
<br />3. 100% OF THE LUMINARIES IN A KITCHEN MUST BE HIGH EFFICACY.
<br />4. IN BATHROOMS, GARAGES, LAUNDRY ROOMS, AND UTILITY ROOMS, AT LEAST ONE LUMINAIRE IN EACH OF THESE
<br />SPACES SHALL BE CONTROLLED BY A VACANCY SENSOR.
<br />5. BEDROOMS, LIVING ROOMS, FAMILY ROOMS AND OTHER ROOMS USED FOR LIVING AND SLEEPING MUST HAVE HIGH
<br />EFFICACY LIGHTING, AND MAY REQUIRE AN OCCUPANT SENSOR WITH A MANUAL-ON/AUTO-OFF FEATURE, OR DIMMERS.
<br />6. EXTERIOR LIGHTING MUST BE HIGH EFFICACY, A PHOTOCELL AND MOTION SENSOR MAY BE INSTALLED.
<br />E.FANS
<br />1. IN BATHROOMS CONTAINING TUBS OR SHOWERS, A FAN CAPABLE OF EXHAUSTING 50 CFM SHALL BE INSTALLED
<br />[ENERGY STANDARDS 150(O)]
<br />2. KITCHEN REQUIRED EXHAUST FAN WITH A MINIMUM 100 CFM DUCTED TO THE EXTERIOR.
<br />3. HUMIDITY CONTROLS SHALL BE CAPABLE OF ADJUSTMENT BETWEEN A RELATIVE HUMIDITY RANGE OF 50% TO A
<br />MAXIMUM 80% A HUMIDITY CONTROL MAY UTILIZE MANUAL AUTOMATIC
<br />F.SMOKE ALARMS
<br />IN NEW CONSTRUCTION. SMOKE ALARMS SHALL RECEIVE THEIR PRIMARY POWER FRONT THE BUILDING WIRING. THE
<br />WIRING SHALL BE PERMANENT AND INSTALLED WITHOUT A DISCONNECTING SWITCH OTHER THAN THOSE REQUIRED OR
<br />OVERCURRENT PROTECTION [CRC R314.4]
<br />A DOMESTIC CLOTHES DRYER DUCT SHALL BE OF METAL AND A MINIMUM OF 4 ” IN DIAMETER. THE EXHAUST DUCT SHALL NOT
<br />EXCEED A TOTAL COMBINED HORIZONTAL AND VERTICAL LENGTH OF 14 ’, INCLUDING TWO 90 DEGREE ELBOWS. TWO FEET
<br />SHALL BE DEDUCTED FOR EACH 90 DEGREE ELBOW IN EXCESS OF TWO (504.3.1.1 & 504.3.1.2 CMC)
<br />ELECTRICAL NOTES
<br />NOTE ALL BATHROOMS FANS:
<br />MINIMUM 50 CFM FAN TESTED AT A STATIC PRESSURE OF .25 WC AND RATED @ 3 SONES OR LESS REQUIRED TO BE INSTALLED
<br />FAN MUST BE ATTACHED TO A MINIMUM 4 ” DUCT AND NO LONGER THAN 70 ’ OF FLEX DUCT. SUBTRACT 15 ’ OF ALLOWED LENGTH
<br />FOR EACH ELBOW.
<br />NOTE ALL KITCHEN RANGE HOODS:
<br />MINIMUM 100 CFM FAN TESTED AT A STATIC PRESSURE OF .25 WC AND RATED @ 3 SONES OR LESS REQUIRED TO BE INSTALLED.
<br />FAN MUST BE ATTACHED TO A MINIMUM 5 ” SMOOTH DUCT AND NO LONGER THAN 85 ’. SUBTRACT 15’ OF ALLOWED LENGTH FOR
<br />EACH ELBOW.
<br /> 3/8" = 1'-0"1 Roof Plan
<br /> 3/8" = 1'-0"2 Electrical Plan
<br />ELECTRIC READY NOTES
<br />1.WATER HEATING SYSTEM (WATER HEATER) (SECTION 150.0(N))
<br />A.SYSTEMS USING GAS OR PROPANE WATER HEATERS TO SERVE INDIVIDUAL DWELLING UNITS SHALL DESIGNATE A SPACE AT
<br />LEAST 2.5 FEET BY 2.5 FEET WIDE AND 7 FEET TALL SUITABLE FOR THE FUTURE INSTALLATION OF A HEAT PUMP WATER HEATER
<br />(HPWH) BY MEETING EITHER A OR B LISTED UNDER SECTION 150.0(N).
<br />I.IF THE DESIGNATED SPACE IS WITHIN 3 FEET FROM THE WATER HEATER:
<br />A.A DEDICATED 125 VOLT, 20 AMP ELECTRICAL RECEPTACLE THAT IS CONNECTED TO THE ELECTRIC PANEL WITH A 120/240 VOLT 3
<br />CONDUCTOR, 10 AWG COPPER BRANCH CIRCUIT, WITHIN 3 FEET FROM THE WATER HEATER.
<br />II. ISOLATE BOTH ENDS OF THE UNUSED CONDUCTOR.
<br />B.A RESERVED SINGLE POLE CIRCUIT BREAKER SPACE IN THE ELECTRICAL PANEL ADJACENT TO THE CIRCUIT BREAKER
<br />C.A CONDENSATE DRAIN THAT ALLOWS NATURAL DRAINING OF THE WATER HEATER.
<br />D.. IF THE DESIGNATED SPACE IS MORE THAN 3 FEET FROM THE WATER HEATER: SEE ADDITIONAL CODE REQUIREMENTS.
<br />B.WHEN A SECOND WATER HEATER IS INSTALLED AS PART OF THE ADDITION SHALL COMPLY WITH SECTION (150.2(A)(D).
<br />1108 N Towner St &
<br />#212/13/2024
|