824 S Harbor Blvd - Plan - Laserfiche WebLink

Home Browse Search

GRAHAM GIBSON CALVIN LOTZ 23.04.13 23.04.13 SCALE:DWG TITLE:PAGE #: REV.#BY DATE DESCRIPTION ORIGINAL BY: REVIEWED BY: DATE: DATE: PLACARDS & NOTES INDIVIDUAL PLOT PLAN NTS COMMUNITY NAME BUILDER ADDRESS SITE ADDRESS DESIGNER INFORMATION 824 SOUTH HARBOR BOULEVARD SANTA ANA, CA 92704 SANTA ANA 7 6531 IRVINE CENTER DR. #200 IRVINE, CA 92618 CITY VENTURES: 01 MA 23.10.05 LAYOUT UPDATE INSTALLATION NOTES: SOLAR CONTRACTOR - 1.ALL PV ROOF ATTACHMENTS WILL BE SPACED ALONG MODULE RACKING RAILS AT NOT GREATER THAN 48" O.C. 2.ALL PV ROOF ATTACHMENTS WILL BE STAGGERED BY ROW AMONGST THE ROOF FRAMING MEMBERS, TO MAXIMUM EXTENT POSSIBLE. 3.ROOF PENETRATIONS ASSOCIATED WITH SOLAR RACKING WILL BE SEALED WITH AN APPROVED SEALANT. 4.ROOFTOP WIRE TRANSITION WILL BE INSTALLED PER MANUFACTURER'S INSTRUCTIONS. IT WILL BE FLASHED AND SEALED. 5.PV ARRAY WILL BE A MINIMUM OF 3" ABOVE THE COMPOSITE SHINGLE ROOF SURFACE. 6.THE RACKING SYSTEM AND SOLAR PV ARRAY WILL BE INSTALLED ACCORDING TO THE MANUFACTURER'S MANUAL AND INSTALLATION GUIDES. 7.MID CLAMPS REQUIRE .37 INCH (3/8") SPACE BETWEEN PV MODULES. RAILS SHALL EXTEND 2" BEYOND ARRAY. SOLAR CONTRACTOR IS RESPONSIBLE FOR PROPER RAIL LENGTH AND INSTALLATION. 8.THE MAXIMUM HEIGHT OF A SOLAR COLLECTOR SHALL BE NO MORE THAN TWO FEET, MEASURED PERPENDICULAR TO THE ROOF SURFACE, AND MY NOT EXCEED THE MAXIMUM OVERALL BUILDING HEIGHT. 9.ALL SOLAR ENERGY SYSTEM APPURTENANCES SHALL BE SCREENED TO THE MAXIMUM EXTENT POSSIBLE WITHOUT COMPROMISING THE EFFECTIVENESS OF THE SOLAR COLLECTORS, AND SHALL BE OF A COLOR SIMILAR TO THE COLOR OF THE SURFACE UPON WITH THEY ARE MOUNTED. 10.THE ADDRESS OF EACH UNIT SHALL BE VISIBLE ON THE SITE PLAN. 11.RAIL/RACKING/MOUNTING SYSTEM HAS BEEN TESTED BASED ON UL 2703 AND CLASSIFIED AS CLASS A FIRE RATED COMPONENTS. (SEE MASTER PERMIT SET AND PROVIDED SPEC SHEETS) 12.PV PANEL HAS BEEN TESTED BASED ON UL 1703. (SEE MASTER PERMIT SET AND PROVIDED SPEC SHEETS) ELECTRICAL NOTES: GENERAL - 1) ALL PV EQUIPMENT WILL BE TESTED AND LISTED FOR ITS USE BY A NATIONALLY RECOGNIZED TESTING LABORATORY (NRTL). 2) THE GROUNDING OF THE PHOTOVOLTAIC SYSTEM SHALL COMPLY WITH THE APPLICABLE VERSION OF THE NEC/CEC. 3) ALL GROUNDING ELECTRODE CONDUCTORS WILL BE INSTALLED IN A CONTINUOUS LENGTH EXCEPT WHERE SPLICED BY AN IRREVERSIBLE CONNECTOR OR EXOTHERMIC WELD. 4) NON-CURRENT CARRYING METAL PARTS SHALL BE CHECKED FOR PROPER GROUNDING, NOTING THAT TERMINAL LUGS BOLTED ON AN ENCLOSURE'S FINISHED SURFACE MAY BE ELECTRICALLY INSULATED BECAUSE OF PAINT/FINISH. PAINT/FINISH AT POINT OF CONTACT SHALL BE PROPERLY REMOVED. 5) ROOF PENETRATIONS WILL BE COMPLETED AND SEALED PER APPLICABLE CODE. 6) ALL CONDUCTORS WILL HAVE A 90°C RATING TO ENSURE CODE COMPLIANCE. 7) PV INVERTERS ARE TESTED AND LISTED FOR COMPLIANCE WITH RAPID SHUTDOWN REQUIREMENTS OF SECTION 690.12 OF THE CEC. SOLAR CONTRACTOR - 8) MODULE CERTIFICATIONS WILL INCLUDE UL1703, IEC61215, IEC61730. 9) CONDUIT AND CONDUCTOR SPECIFICATIONS ARE BASED ON MINIMUM CODE REQUIREMENTS. 10) RACEWAY POINT OF PENETRATION FROM EXTERIOR TO INTERIOR WILL BE SEALED TO PREVENT INGRESS OF WATER AND INSECTS. 11) MODULE AND MODULE LEVEL POWER ELECTRONICS WIRING SHALL BE LOCATED AND SECURED UNDER THE ARRAY USING SUITABLE WIRING CLIPS. WIRING SHALL NOT MAKE CONTACT WITH THE ROOF SURFACE AND SHALL BE MANAGED IN A WORKMAN-LIKE MANNER. 12) EQUIPMENT GROUNDING CONDUCTORS WILL BE SIZED IN ACCORDANCE WITH CEC 250.122. 13) CONDUCTOR TERMINATIONS WILL BE TORQUED PER DEVICE LISTING, OR MANUFACTURER'S RECOMMENDATIONS. 14) CABLE OR OTHER MEANS TO CONNECT INVERTER TO INTERNET 15) INSTALLATION SHALL BE COMPLETED IN A NEAT AND WORKMAN-LIKE MANNER. 16) SPACE REQUIREMENTS FOR ALL ELECTRICAL EQUIPMENT WILL COMPLY WITH CEC ARTICLE 110.26. SIGNAGE - 17) PV SYSTEMS SHALL BE CLEARLY MARKED IN ACCORDANCE WITH CEC ARTICLE 690 AND OTHER APPLICABLE STATE AND LOCAL CODES. 18) ALL SAFETY MARKING / PLACARDS SHALL BE PERMANENTLY ATTACHED BY ADHESIVE OR OTHER MECHANICAL MEANS. 19) MARKING / PLACARDS WILL BE METAL OR PLASTIC WITH ENGRAVED OR MACHINE PRINTED LETTERING IN COMPLIANCE WITH ANSI STANDARDS. 20) ALL WIRING/RACEWAYS/JUNCTION BOXES WILL BE MARKED "WARNING: PHOTOVOLTAIC POWER SOURCE," OR EQUIVALENT; WIRING/RACEWAYS SHALL BE MARKED EVERY 10'. CA License #: 1003498 Classification: B, C10, C46 Namaste Solar Electric 888 Federal Boulevard Denver, CO 80204 Designer: Owner: Sunnova Energy Corporation 6531 Irvine Center Dr. #200 Irvine, CA 92618 4 824 S Harbor Blvd 11/15/2023