Laserfiche WebLink
ROOF MOUNT CROSS SECTION DETAIL <br />NTS <br />ROOF FRAMING <br />SEE TABLE ON SHEET PV-3 <br />PV MODULE <br />FINISHED ROOF <br />GROUND END/MID CLAMP <br />SHEATHING <br />RAIL <br />ECOFASTEN CLICKFIT UNIVERSAL TILE <br />HOOK ROOF MOUNT WITH (2) SCREWS <br />CONNECTED TO ROOF FRAMING <br />WATERPROOF BUTYL <br />(2) 5/16" x 4" LAG SCREWS PROVIDED <br />BY MANUFACTURER CONNECTED <br />INTO ROOF FRAMING <br />EMBEDMENT DEPTH SEE <br />TABLE ON SHEET PV-3 <br />GENERAL ROOF MOUNT DETAIL <br />NTS ROOF MOUNT PLAN VIEW DETAIL <br />NTS <br />ENGINEERED PLANS COMPLETED BY ENGINEERS IN THE USA <br />CALIFORNIA LICENSE NO. C83664 <br />VANDERVOORT, DAVID <br />2307 NORTH TOWNER STREET <br />SANTA ANA, CA 92706 <br /> PN/PARCEL NO: 00121406 <br />EXO ENERGY <br />1358 LA MIRADA DRIVE <br />SAN MARCOS, CA 92071 <br />(208) 351-4153 <br />MICHAEL ESPINOZA <br />CSLB: 1063308 <br />S-1 <br />DATE: <br />SCOTT E. WYSSLING, P.E. <br />7/26/2024 <br />swyssling@wysslingconsulting.com <br />(201) 874-3483 <br />DESIGN ENGINEER <br />SOLAR COMPANY/CLIENT <br />76 N. MEADOWBROOK DRIVE <br />ALPINE, UTAH 84004 <br />STRUCTURAL <br />DETAILS <br />ECOFASTEN CLICKFIT UNIVERSAL TILE HOOK <br />FLASHING ROOF MOUNT SEE ROOF MOUNT CROSS <br />SECTION DETAIL THIS SHEET FOR CONNECTION TO <br />ROOF FRAMING <br />ROOF FRAM <br />I <br />N <br />G <br />SEE TABLE <br /> <br />O <br />N <br /> <br />S <br />H <br />E <br />E <br />T <br /> <br />P <br />V <br />- <br />3 <br />FINISHED ROOF <br />ROOF SHEATHING <br />PV MODULE <br />RAIL <br />3" MIN - 6" <br />MAX SPACE <br />FROM ROOF <br />SURFACE ECOFASTEN CLICKFIT UNIVERSAL TILE <br />HOOK ROOF MOUNT WITH (2) SCREWS <br />CONNECTED TO ROOF FRAMING <br />(2) 5/16" x 4" LAG SCREWS <br />PROVIDED BY MANUFACTURER <br />CONNECTED INTO ROOF FRAMING <br />1.CONTRACTOR IS TO FOLLOW THE PLAN FOR INSTALLING <br />ROOF MOUNTS. <br />2.IF THE CONTRACTOR IDENTIFIES THE ROOF FRAMING IS <br />DIFFERENT FROM WHAT IS IDENTIFIED ON THIS PLAN, <br />CONTRACTOR SHALL NOTIFY THE ENGINEER BEFORE <br />PROCEEDING WITH INSTALLATION. <br />3.CONTRACTOR IS TO LOCATE THE ROOF FRAMING BY <br />UTILIZING A HAMMER. <br />4.WHEN THE ROOF FRAMING IS LOCATED, CONTRACTOR IS TO <br />DRILL A PILOT HOLE TO CONFIRM CENTER OF ROOF FRAMING. <br />IF THE ROOF FRAMING IS MISSED, AND A NEW PILOT HOLE IS <br />TO BE DRILLED, CONTRACTOR TO UTILIZE SILICON/CAULK TO <br />SEAL THE ORIGINAL PILOT HOLE. <br />5.DIRECT TO DECK MOUNTS ARE ONLY TO BE USED WITH <br />APPROVED DESIGN BY THE ENGINEER. DIRECT TO DECK <br />MOUNT INSTALLATION IS NOT A SUBSTITUTION FOR LAG <br />SCREWS INTO ROOF FRAMING. <br />6.CONTRACTOR TO FOLLOW MANUFACTURERS <br />SPECIFICATIONS FOR INSTALLATION AND REQUIRED SCREWS. <br />MOUNT INSTALLATION NOTES <br />Signed 7/26/2024 <br />2307 N Towner St <br />8/23/2024