1414 W Edinger Ave - Plan - Laserfiche WebLink

Home Browse Search

FIN. FLR. LEV. WHERE REQUIRED) (USE REDUCING TYPE COMB. "Y" & 1/8" BEND 6" Thk. CONCRETE PAD SEWER MATERIAL AND SIZE AS SPECIFIED DUTY REQUIRED w/ COVER FOR GRADE OR PAVING CAST IRON CLEANOUT (V E R I F Y @ S I T E ) VA R I E S 6" DIA. SEWER UP TO SAME SIZE AS EXTENSION CAST IRON CENTER PIPE SLEEVE. INSULATION LATION) IN (AND INSU- IF WALL IS PRE- THRU SLEEVE: DO NOT BUTT AGAINST WALL. CONTINUES WILL NOT HAVE OMIT SLEEVE. CONCEALED PIPE ESCUTCHEON TO CAST CONCRETE, CORE DRILL AND COVER PENETRATION. REFER TO SPECIFICATIONS FOR ALTERNATIVE INSTALLATIONS. REFER TO ARCHITECTURAL DRAWINGS FOR WALL LOCATIONS. PROVIDE GALVANIZED STEEL PIPE SLEEVE EXPOSED PIPE SHALL HAVE ESCUTCHEON TO COVER PENETRATION. GROUTED INTO WALL. PIPE OR CONDUIT UNIT CONSTRUCTION IF WALL IS MASONRY OR POURED CONCRETE, INSULATED PIPE UNINSULATED PIPE GLASS INSULATION SPACE BETWEEN SLEEVE AND PIPE SOLID WITH FIBER- PACK ANNULAR (FOR ACOUSTICS). CAST IRON LONG SWEEP 1/4" BEND OR CAST IRON SLEEVE FLUSH WITH WALL PIPE OR MINIMUM 18 GA GALVANIZED STEEL WALLBOARD, PROVIDE PLACE AS REQUIRED. OR GROUT SLEEVE IN METAL SLEEVE. CAULK GALVANIZED SHEET ROOFING CONSTRUCTION VENT STACK ROOF CONSTRUCTION LEAD FLASHING MOP IN WITH ROOFING MATERIAL INCREASER WHEN REQUIRED SHEET LEAD FLASHING MI N . 1 2 " AS REQUIRED SLEEVE ROOF MIN.12" TURN LEAD DOWN INTO STACK WOOD STRUCTURE 4"=5/8". LOCATE HANGERS WITHIN 1'-0" OF VALVES AND FITTINGS. DO NOT SUSPEND PIPE FROM JOIST BRACING MEMBERS. REFER TO CODES AND SPECIFICATIONS FOR FURTHER INFORMATION. PROVIDE SEISMIC CHAINS AND PERFORATED STRAP IRON AND STEEL ARE NOT ACCEPTABLE. WATER PIPE AGAINST SWAYING DUE TO CHANGES IN WATER VELOCITY. LOCATE HANGERS WITHIN 1'-0" OF EQUIPMENT CONNECTIONS. ANCHOR PROVIDE SUPPLEMENTAL STEEL STRUTS BETWEEN JOISTS IF REQUIRED. BRACING IF/AS REQUIRED BY LOCAL AUTHORITIES. PENETRATE VAPOR BARRIER. DO NOT HANG ONE PIPE FROM ANOTHER ROD SIZES FOR PIPE SIZE: 2" AND SMALLER=3/8", 2 1/2" TO 3"=1/2", INDICATED IN TABLE. CAST IRON: 10' AND WITHIN 1'-0" OF ALL JOINTS. DRAINABLE LOCATIONS. HANGER SPACING FOR PIPE SIZES: AS EXCEPT IN CHASES. SLOPE ALL WATER PIPING SLIGHTLY TOWARD THICKNESS WHEN SIZING HANGERS AND SHIELDS. HERE. DO NOT INSTALL HANGER INSIDE INSULATION OR OTHERWISE PROVIDE UPPER ATTACHMENT AS REQUIRED FOR CASES NOT SHOWN ALL INSULATED PIPE. VERIFY INSULATION PROVIDE GALVANIZED STEEL SHEILD FOR 8'6'1" 3" 4"10' 10'10' 10' 1-1/2" 2" 2-1/2" 1-1/4" 10'6' 10' 10'10' 10' 6'10' AND SMALLER HA N G E R S P A C I N G ST E E L P I P E HA N G E R S P A C I N G PI P E S I Z E CO P P E R P I P E 1/2"1/2" 3/4" 6'6' 6'6' HANG PIPE LARGER THAN 4" FROM TOP OF JOISTS AND CAST IRON PIPE 2" ADJUSTABLE BAND HANGER FOR PIPE 3-1/2" AND SMALLER SIDE BEAM CONNECTOR CHORD OF WOOD TRUSS ATTACHED TO TOP ONLY AT PANEL POINT CONTACT BARE COPPER PIPE PROVIDE COPPER WHERE HANGERS COATED HANGERS ALL-THREAD ROD WALL CONDENSATE DRAIN VENT FLEX. HOSE CONNECTION DRAIN FIN. FLOOR LAVATORY OR SINK TAILPIECE SLIP JOINT P-TRAP ROOF HVAC UNIT ON ROOF 3" HIGH,RUNNING TRAP. HANGER ROD HEAVY DUTY SUPPORT NUT LOCKING NUT 8" LONG MINIMUM WITH VAPOR BARRIER INSULATION INSULATION VAPOR BARRIER SHEET STEEL SADDLE 16 GA. ZINC COATED CLEVIS HANGER PIPEHEAVY DUTY NO VAPOR BARRIER INSULATION SINGLE HORIZONTAL RUNS CLEVIS HANGER CLEVIS HANGER PIPE SINGLE HORIZONTAL RUNS CLEVIS HANGER HANGER ROD LOCKING NUT SUPPORT NUT MAX.4"-0" MAX.12" H NOTES: 1.DETAIL PROVIDED FOR UTILITY REQUIREMENTS. REFER TO MANUFACTURER'S INSTALLATION GUIDE FOR ADDITIONAL INFORMATION. HENRY SCHEIN DENTAL REP WILL PROVIDE INSTALLATION TEMPLATE UPON REQUEST. 2.INSTALLATION MUST CONFORM TO ALL LOCAL ELECTRICAL AND PLUMBING CODES. 3.ALL UTILITIES HEREIN TO BE SUPPLIED & INSTALLED BY LICENSED CONTRACTORS. FINAL CONNECTIONS TO EQUIPMENT BY HENRY SCHEIN DENTAL. 4.ALL VALVES, BOXES AND PIPES FROM FLOOR MUST BE NO HIGHER THAN 5 1/4" A.F.F. 5.ALL PLUMBED SYSTEMS MUST BE FLUSHED CLEAN OF ANY DEBRIS PRIOR TO EQUIPMENT INSTALLATION. 3 DCI EDGE SERIES 5 CABINET UTILITIES TOP VIEW COMPRESSED AIR: 1/2" SUPPLY LINE FROM COMPRESSOR BY PLUMBER. STUB-UP FROM FLOOR 1”-2”. TERMINATE WITH 3/8” ANGLE VALVE. PRESSURE 100 PSI MAX. WATER: 1/2" COLD WATER SUPPLY LINE BY PLUMBER. STUB-UP FROM FLOOR 1”-2”. TERMINATE WITH 3/8" ANGLE VALVE. PRESSURE 40 PSI MAX. ELECTRICAL: 16" FLEX CONDUIT WITH TWO GANG BOX & 115V QUAD OUTLET BY ELECTRICIAN. MAX DRAW: 15A CENTRAL VACUUM: 5/8" RISER BY PLUMBER (SCH. 40 PVC OR TYPE M COPPER). TERMINATE 1"-2" A.F.F. A W E V UTILITIES TO BE RUN IN FLOOR OR WALL BASED ON SITE CONDITIONS CL W C A V 3-3/8" SUPPORT WALL FOR FREESTANDING CABINET CONDUIT: PVC CONDUIT WITH PULL-STRING BY ELECTRICIAN. 6" MIN. RADIUS FOR ALL BENDS. STUB-UP FLUSH WITH SUB-FLOOR, MARK LOCATION AT FINISH. QUANTITY OF CONDUIT TERMINATIONS WILL VARY, SEE SHEET SE.1 FOR SIZES & LOCATIONS. C ELEVATION VIEW CL AVAILABLE SPACE FOR PLACEMENT OF UTILITIES (LOCATE AS NEEDED) W A E CABINET TOE KICK UTILITIES TO STUB-OUT FROM WALL 6" (MIN.) FINISHED FLOOR ALLOW 16" ELECTRICAL WHIP TO EXTEND FROM STUB-OUT FOR HOOK-UPS V CABINET BASE CUT-OUTS WITHIN CABINET BASE DWV WYE FITTING VACUUM LINE GUIDELINES SUB FLOOR BRANCH EXAMPLES THE VACUUM PIPING LAYOUT HAS A LARGE EFFECT ON THE EFFICIENCY AND RELIABILITY OF THE DENTAL VACUUM SYSTEM. REFER TO MANUFACTURER'S PRE-INSTALLATION GUIDE PROVIDED BY HENRY SCHEIN EQUIPMENT SPECIALIST (FOR SPECIFIC SIZING OF STUB-UP, TRUNK, AND BRANCH LINES. IT IS HIGHLY RECOMMENDED THAT VACUUM LINES RUN UNDERNEATH DENTAL EQUIPMENT BY MEANS OF TRENCHING/CORING (CONCRETE SLAB) OR SUB-FLOOR (BASEMENT/CRAWL SPACE). ALL LINES ARE TO BE DESIGNED WITH PVC PIPING UNLESS DICTATED BY LOCAL CODES TO USE COPPER OR CAST IRON. I. STUB-UP TERMINATE VACUUM TRUNK LINE IN MECHANICAL ROOM. PLUMBER TO PROVIDE FPT ADAPTOR ON END OF STUB-OUT FROM FLOOR OR WALL, SIZE PER MANUFACTURER SPECIFICATIONS. SEE DETAILS (THIS SET) & MANUFACTURER TEMPLATES PROVIDED BY HENRY SCHEIN EQUIPMENT REP. IN THE CASE OF DUAL TRUNK LINE SYSTEM, PROVIDE ENOUGH SPACE BETWEEN STUB-UPS TO INSTALL BYPASS OR TANDEM COMPONENTS. 2. TRUNK LINE(S) DO NOT PIPE TRUNK LINE IN A SERIES MANNER FROM J-BOX TO J-BOX. A CONTINUOUS TRUNK LINE MUST BE MAINTAINED FROM THE PUMP TO THE FURTHEST J-BOX USING BRANCH LINES OFF OF THE TRUNK LINE TO PICK UP EACH VACUUM OUTLET. TRUNK LINE MAY FOLLOW DRAIN LINE TRENCHES WITHIN REASON. 3. BRANCH LINE(S) BRANCH LINES ARE TO HAVE "SWEEPING" 90 DEGREE TURNS TO AVOID VACUUM LOSS. "WYE" FITTINGS SHOULD BE USED TO JOIN BRANCH LINES TO THE TRUNK LINE. 4. PLUMBING AROUND FOOTINGS: IF VACUUM LINES ENCROACH ON EITHER A WALL OR COLUMN FOOTING, USE 45 DEGREE ELBOWS TO PIPE AROUND FOOTING TO FINAL LOCATION. DO NOT PIPE UNDER FOOTINGS. TURNS/INTERSECTIONS) VACUUM NOTES DWV WYE 45° ELBOW DWV OFFSET WYE DWV LONG SWEEP ELBOW FLOW TO PUMP FLOW TO PUMP DWV 45° ELBOWS REDUCER BUSHING TRUNK LINE BRANCH LINE STUB-UP IN TREATMENT FLOW VACUUM LINES MUST BE SUPPORTED EVERY 6'-0" TO PREVENT SAGGING. ENTIRE SYSTEM MUST MAINTAIN A MINIMUM OF 1/4" PER 10'-0" TOWARD THE VACUUM PUMP. DO NOT USE ANY 90° SHORT ELBOWS SCH 40 PVC TURNS/ INTERSECTIONS ARE TO BE PLUMBED USING ALLOWED DWV FITTINGS. DO NOT CREATE TRAPS IN TRUNK/BRANCH LINES. Scale Date Drawn By Checked By Project Number REVISIONS JOB SITE: PLAN: PHONE: PLAN CHECK / JOB NO. 50 S DE LACEY AVE. STE. 210 Pasadena, CA 91105 THESE PLANS ARE FOR REVIEW ONLY AND NOT FOR CONSTRUCTION UNLESS THEY INCLUDE THE STAMP AND SIGNATURE OF ARCHITECT/ENGINEER AND THE APPROVAL OF THE APPROPRIATE GOVERNMENT AGENCY C-38176 MARC A. ABDELSAYED RENEWAL DATE LICENSED A R CHITECT STATE OF C ALIFORNIA 07/31/2025 369 ARCHITECTS As Noted CA N A M D E N T A L - SA N T A A N A MARS NASRIN.P. 07/29/2024 MISC._24065 No.Description Date 1414 W. EDINGER AVE, SANTA ANA, CA. 92704 .PERMIT 09/04/2024 09 / 0 4 / 2 0 2 4 _ G C C o m m e n t 1 P.C.COMMENTS 02/01/2025 P-5.0 PLUMBING DETAILS