1312 E Warner Ave - Plan - Laserfiche WebLink

Home Browse Search

ALL WORK SHALL COMPLY WITH ALL STATE AND LOCAL CODES AND ANY OTHER REGULATING AUTHORITIES WHICH HAVE AUTHORITY OVER ANY PORTION OF THE WORK. PRIOR TO COMMENCEMENT OF ANY WORK, THE CONTRACTOR SHALL VERIFY EXISTING CONDITIONS AND NOTIFY THE DESIGN PROFESSIONAL IN RESPONSIBLE CHARGE FROM TESLA OF ANY DISCREPANCIES. ANY WORK PERFORMED IN CONFLICT WITH THE CONTRACT DOCUMENTS SHALL BE CORRECTED AT THE SUBCONTRACTORS SOLE EXPENSE. SUBCONTRACTOR INITIATED CHANGES SHALL BE SUBMITTED IN WRITING TO TESLA FOR APPROVAL BEFORE MAKING ANY CHANGES. DEVIATION FROM PLANS BEFORE WRITTEN APPROVAL FROM TESLA PLACES LIABILITY ON THE SUBCONTRACTOR. ALL EQUIPMENT SHALL BE MOUNTED AS SHOWN. WHERE DETAILS ARE NOT PROVIDED, CONTRACTOR SHALL USE STANDARD CONSTRUCTION PRACTICES. ALL SURFACES SHALL BE PATCHED AND PAINTED AROUND NEW DEVICES AND EQUIPMENT TO MATCH EXISTING FINISHES. ANY METAL SHAVINGS FROM SITE WORK SHALL BE CLEANED FROM ALL SURFACES WHERE OXIDIZED OR CONDUCTIVE METAL SHAVINGS MY CAUSE RUST, ELECTRICAL SHORT CIRCUITS, OR OTHER DAMAGE. APPROVALS FROM BUILDING INSPECTORS SHALL NOT CONSTITUTE AUTHORITY TO DEVIATE FROM THE DRAWINGS. NEW PAVEMENT INSTALLED AS PART OF THIS PROJECT SHALL MATCH EXISTING PAVEMENT SECTION. ASPHALT AND GAB DEPTHS SHALL BE MAINTAINED. GENERAL NOTES GENERAL NOTES 1.ALL ELECTRICAL WORK SHALL COMPLY WITH THE NATIONAL ELECTRIC CODE AS AMENDED BY APPLICABLE STATE AND LOCAL CODES. 2.ALL WIRING SHALL BE MANAGED IN A PROFESSIONAL, WORKMAN-LIKE MANNER AND MUST BE SUPPORTED, SECURED, AND PROTECTED TO PREVENT DAMAGE. 3.AC CIRCUIT CONDUCTORS SHALL BE IDENTIFIED BY PHASE AND SYSTEM PER ART 210.5 OR 215.12. UNLESS OTHERWISE REQUIRED BY ART 210.5(1) OR AHJ, COLOR-CODING OF POWER CONDUCTORS SHALL BE AS FOLLOWS: CONDUCTOR 277/480V 120/208V PHASE A BROWN BLACK PHASE B ORANGE RED PHASE C YELLOW BLUE NEUTRAL GRAY WHITE 4.DC CIRCUIT CONDUCTORS SHALL BE IDENTIFIED PER ART 210.5 OR 215.12: CONDUCTOR STD COLOR ALT COLOR DC+RED RED-STRIPED DC-BLACK BLACK-STRIPED 5.TERMINATIONS OF AC, DC, AND COMMUNICATIONS CONDUCTORS SHALL BE PROFESSIONALLY AND LEGIBLY LABELED WITH CIRCUIT SCHEDULE IDENTIFIER, CONDUCTOR SIZE (AS APPLICABLE) AND TERMINATION TORQUE. 6.ALL EQUIPMENT SHALL BE LISTED BY A NRTL IN COMPLIANCE WITH ART 110.3. WHERE EXISTING NRTL LISTING CANNOT BE MAINTAINED, ENGINEERING APPROVAL SHALL BE OBTAINED PRIOR TO EQUIPMENT MODIFICATION, AND THE EQUIPMENT SHALL BE RELISTED BY A SUITABLE NRTL. 7.UNDERGROUND CONDUCTORS & CABLES TO BE INSTALLED IN CONDUIT UON. 8.ALL WIRES SHALL BE PROVIDED WITH STRAIN RELIEF AT ALL ENTRY INTO BOXES AS REQUIRED BY NRTL LISTING. 9.REFER TO MANUFACTURER'S CURRENT PLANNING AND INSTALLATION MANUAL FOR TORQUE SPECS FOR ALL BOLTS AND TERMINAL CONNECTIONS. 10.ALL CONDUCTOR TERMINATIONS ON BUSSING OR TRANSFORMER SPADES SHALL BE MADE WITH HIGH-PRESS CRIMP LUGS UON. 11.ALL TERMINATIONS OF ALUMINUM CONDUCTORS SHALL BE PROPERLY INSTALLED WITH BEST PRACTICES INCLUDING BUT NOT LIMITED TO: ·USE OF TERMINATION EQUIPMENT RATED FOR ALUMINUM AT THE CONDUCTOR TEMPERATURE, CURRENT, AND VOLTAGE ·ALLOWANCE FOR MOVEMENT DUE TO THERMAL EXPANSION/CONTRACTION ·PROPER COATING OF EXPOSED ALUMINUM WITH ANTI-OXIDIZATION COMPOUND ·USE OF CALIBRATED DEVICES TO TORQUE AND MARK TERMINALS TO REQUIRED SETTINGS 12.DUCT SEAL COMPOUND SHALL BE APPLIED WHEREVER CONDUITS TRANSITION INDOOR/OUTDOOR OR UNDERGROUND/ABOVEGROUND. REFER TO EQUIPMENT NOTES FOR ADDITIONAL DUCT SEAL REQUIREMENTS. 13.BELL ENDS SHALL BE INSTALLED WHEREVER CONDUIT ENTERS EQUIPMENT FROM UNDERGROUND AND WHEREVER POTENTIAL FOR DAMAGE TO CONDUCTORS IS PRESENT AT ANY POINT. BELL ENDS SHALL NOT PREVENT THE USE OF GROUNDING FITTINGS OR COUPLERS WHEN REQUIRED. 14.ALL STUB-UPS WITHIN FLOOR-MOUNTED EQUIPMENT SHALL BE 3-5" ABOVE FINISHED GRADE. 15.ALL CONDUITS EXPOSED TO VEHICULAR OR EQUIVALENT PHYSICAL DAMAGE SHALL BE RIGID GALVANIZED STEEL. 16.GROUND LUGS SHALL BE RATED FOR THEIR ENVIRONMENT AND CONDITION OF USE. ELECTRICAL NOTES 1.LOAD SIDE INTERCONNECTIONS SHALL COMPLY WITH NEC ART 705.12(B). 2.WHERE THE INTERCONNECTION POINT OCCURS ON FEEDERS, THE FEEDER AMPACITY SHALL NOT BE LESS THAN THE SUM OF ALL THE SOURCES CONNECTED TO THE FEEDER UNLESS THE FEEDER IS PROTECTED ON THE LOAD SIDE OF THE INTERCONNECTION POINT WITH OVERCURRENT PROTECTION NO GREATER THAN THE AMPACITY OF THE FEEDER. 3.TAP CONNECTIONS SHALL COMPLY WITH ART 240.21(B). 4.WHERE THE SUM OF ALL THE OVERCURRENT DEVICE RATINGS ON THE PANEL LOAD SIDE OF A MAIN OVERCURRENT PROTECTION DEVICE ARE LESS THAN THE RATING OF THE PANEL, PERMANENT WARNING LABELS WITH THE FOLLOWING WORDING MUST BE APPLIED: WARNING: THIS EQUIPMENT FED BY MULTIPLE SOURCES. TOTAL RATING OF ALL OVERCURRENT DEVICES EXCLUDING MAIN SUPPLY OVERCURRENT DEVICE SHALL NOT EXCEED THE AMPACITY OF THE BUSBAR. 5.WHERE THE SUM OF THE UTILITY OVERCURRENT DEVICE AND 125% OF INVERTER OUTPUT CIRCUIT CURRENT DOES NOT EXCEED 120% OF THE RATING OF THE BUSBAR, THE INTERCONNECTION POINT MUST BE ON THE OPPOSITE END OF THE BUSBAR FROM THE INCOMING UTILITY SOURCE AND A PERMANENT WARNING LABEL MUST BE APPLIED TO THE INTERCONNECTION POINT. 6.LOAD SIDE INTERCONNECTIONS SHALL BE MADE IN ACCORDANCE WITH THE EQUIPMENT MANUFACTURER'S INSTRUCTIONS AND SHALL NOT INVALIDATE THE NRTL LISTING OF THE EQUIPMENT. WHERE EXISTING NRTL LISTING CANNOT BE MAINTAINED, EQUIPMENT MUST BE RELISTED BY AN APPROVED NRTL SUITABLE FOR THE EQUIPMENT. UTILITY-INTERACTIVE INVERTER LOAD-SIDE INTERCONNECTION NOTES 1.CAT5E/6 SHIELDED CABLE RUNS, WHICH INCLUDE INDIVIDUAL DAISY CHAINS OF INVERTERS FOR DIRECT MONITORING, HAVE A MAXIMUM TOTAL DISTANCE OF 328 FEET (100M) PER CHAIN. 2.RS485 CABLE RUNS, WHICH INCLUDE INDIVIDUAL DAISY CHAINS OF INVERTERS FOR DIRECT MONITORING, HAVE A MAXIMUM TOTAL DISTANCE OF 3280 FEET (1000M) PER CHAIN. 3.SWITCHES, METERS, POWERPACK CONTROLLERS, CT'S, AND PT'S, AND CONDUCTORS MARKED "PRE-INSTALLED" IN THE LINE DIAGRAM WILL ARRIVE TO SITE PRE-INSTALLED WITHIN THE SWITCHBOARD, AND WILL NOT REQUIRE ANY FIELD INSTALLATION OR MODIFICATION OF ANY KIND. 4.FIBER OPTIC CABLE RUNS SHALL UTILIZE OUTDOOR DUCT OR DIRECT BURIAL RATED SINGLE MODE (OS2) CABLES COMPATIBLE WITH COMMUNICATION WAVELENGTHS BETWEEN 1310 - 1550 NM. COMMUNICATION NOTES GENERAL NOTES 1.REFER TO THE SPECIFIC PRODUCT MANUFACTURER'S INSTALLATION AND OPERATION MANUAL FOR MORE INFORMATION. 2.BATTERY ENERGY STORAGE SYSTEM (BESS) SHALL BE SERVICED ONLY BY MANUFACTURER-CERTIFIED TECHNICIANS. 3.SECONDARY CONTAINMENT IS NOT REQUIRED FOR THE BATTERY BESS. 4.BATTERY PACK DC CONNECTIONS TO BESS INVERTER SHALL ONLY BE MADE WITH MANUFACTURER-PROVIDED CONDUCTOR HARNESSES. 5.BESS DISCONNECTING MEANS SHALL BE LABELED PER ART 706.7(D). BESS AND INTERCONNECTION SHALL BE LABELED PER ART 706.11. BESS NOTES SITE LEGEND (E) ACCESSIBLE PARKING SPACE (E) LIGHT POLE FH (E) FIRE HYDRANT G E SS SD T TV ? W GV HB IV WV WR T CO (E) STORM MANHOLE (E) GUY WIRE - ELECTRIC (E) HOSE BIB (E) GAS VALVE (E) IRRIGATION VALVE (E) WATER VALVE (E) SPRINKLER HEAD (E) WATER RISER (E) SPRINKLER HEAD (E) CLEANOUT (E) ELECTRIC MANHOLE (E) GAS MANHOLE (E) SANITARY SEWER MANHOLE (E) TELEPHONE MANHOLE (E) TELEVISION MANHOLE (E) UNKNOWN MANHOLE (E) POTABLE WATER MANHOLE (E) UTILITY POLE - ELECTRIC (E) UTILITY POLE - TELEPHONE (E) GUY WIRE (E) TREE UE (E) UNDERGROUND ELECTRIC LINE ST (E) UNDERGROUND STORM DRAIN LINE WL (E) UNDERGROUND WATER LINE UG (E) UNDERGROUND GAS LINE OE (E) OVERHEAD ELECTRIC LINE UT (E) UNDERGROUND TELEPHONE LINE SS (E) UNDERGROUND SANITARY SEWER LINE (E) VENT PIPE (E) ROOF ACCESS HATCH (E) EXHAUST FAN (E) SKYLIGHT (E) HVAC UNIT (E) OPERABLE SKYLIGHT (E) CONDENSATION CONDUIT LINEWL GAS ELE (E) GAS CONDUIT LINE (E) ELECTRICAL CONDUIT LINE (E) UTILITY POLE GENERAL NOTES 1.TESLA, AT THE TIME OF INSTALLATION, SHALL CONFIGURE THE AUGMENTED MEGAPACKS SUCH THAT: 1.1.THE INTERNAL MEGAPACK CONTROLLER ADJUSTS THE MAXIMUM ALLOWABLE CURRENT OF THE INVERTERS WITH FIRMWARE SO THAT THE AUGMENTED MEGAPACK'S CURRENT CAPABILITY AND THUS KVA RATING ARE MAINTAINED, REGARDLESS OF THE NUMBER OF INVERTERS. 1.2.THE CURRENT IS LIMITED AT THE INVERTER LEVEL, THE SHORT-CIRCUIT CONTRIBUTION OF THE AUGMENTED MEGAPACK REMAINS UNCHANGED. BESS AUGMENTATION NOTES 1"12"0 PROPRIETARY AND CONFIDENTIAL ABCDEFGH 1 2 3 4 5 6 DA T E NO . RE V I S I O N ORIGINAL SIZE 24"X36" SHEET SIZE ARCH "D" 3500 DEER CREEK RD. PALO ALTO, CA 94304 (650) 681-5000 CA L P I N E I I 13 1 2 E W A R N E R A V E SA N T A A N A , C A 9 2 7 0 5 NOTES G-002 REV: 0 PERMIT VQUIRINDONGOPLOT DATE: 10/27/2023 9:36 AM JB-###### CA L P I N E - - P H A S E 2 ME G A P A C K S Y S T E M A U G M E N T A T I O N 1312 E Warner Ave - 101117461 & 201815044/29/2024