2202 N Santiago St - Plan - Laserfiche WebLink

Home Browse Search

1. No enforced DC/AC ratio. See the compatibility calculator at https://enphase.com/en-us/support/module-compatibility. 2. Nominal voltage range can be extended beyond nominal if required by the utility. 3. Limits may vary. Refer to local requirements to define the number of microinverters per branch in your area. To learn more about Enphase offerings, visit enphase.com © 2022 Enphase Energy. All rights reserved. All trademarks or brands used are the property of Enphase Energy, Inc. 10-18-2022 INPUT DATA (DC) IQ7HS-66-M-US Commonly used module pairings¹ 320 W - 460 W + Module compatibility Maximum input DC voltage 66-cell PV modules 59 V Peak power tracking voltage Operating range Min/Max start voltage 38 V - 43 V 20 V - 59 V 30 V / 59 V Max DC short circuit current (module Isc) Overvoltage class DC port DC port backfeed current PV array conﬁguration 15 A II 0 A 1 x 1 ungrounded array; No additional DC side protection required; AC side protection requires max 20A per branch circuit OUTPUT DATA (AC) @240 VAC @208 VAC Peak output power 384 VA 369 VA Maximum continuous output power 384 VA 369 VA Nominal (L-L) voltage/range² 240 V / 211-264 V 208 V / 183-229 V Maximum continuous output current 1.60 A (240V) 1.77 A (208V) Nominal frequency 60 Hz 60 Hz Extended frequency range 47 to 68 Hz 47 to 68 Hz AC short circuit fault current over 3 cycles 4.82 A 4.82 A Maximum units per 20 A (L-L) branch circuit³ 10 9 Overvoltage class AC port III III AC port backfeed current 18 mA 18 mA Power factor setting 1.0 1.0 Power factor (adjustable) 0.85 leading ...0.85 lagging 0.85 leading ...0.85 lagging EFFICIENCY @240 V @208 V CEC weighted efﬁciency 97.0 % 96.5 % MECHANICAL DATA Ambient temperature range Relative humidity range Connector type Dimensions (WxHxD) Weight Cooling Approved for wet locations Pollution degree Enclosure Environmental category / UV exposure rating Altitude -40ºC to +60ºC 4% to 100% (condensing) Staubli made MC4 212 mm x 175 mm x 30.2 mm (without bracket) 1.08 kg (2.38 lbs) Natural convection - No fans Yes PD3 Class II, corrosion resistant polymeric enclosure NEMA type 6 / outdoor 2000m FEATURES Communication Power Line Communication (PLC) Disconnecting means The AC and DC connectors have been evaluated and approved by UL for use as the load-break disconnect means required by NEC 690 and C22.1-2018 Rule 64-220. Compliance CA Rule 21 (UL 1741-SA), HECO v1.1 UL 62109-1, UL1741/IEEE1547, FCC Part 15 Class B, ICES-0003 Class B, CAN/CSA-C22.2 NO. 107.1-01 This product is UL Listed as PV Rapid Shut Down Equipment and conforms with NEC-2014, NEC- 2017 section 690.12, NEC 2020 and C22.1-2015 Rule 64-218 Rapid Shutdown of PV Systems, for AC and DC conductors, when installed according to manufacturer’s instructions. Enphase IQ7HS Microinverter The high-powered smart grid-ready Enphase IQ7HS Microinverter™ with integrated MC4 connectors dramatically simplify the installation process while achieving the highest system efﬁciency. The IQ Series Microinverters extend the reliability standards set forth by previous generations and undergo over a million hours of power-on testing, enabling Enphase to provide an industry-leading warranty of up to 25 years. Enphase IQ7HS Microinverter To learn more about Enphase offerings, visit enphase.com Data Sheet Enphase Microinverters Region: AMERICAS Easy to Install • Lightweight and simple • Faster installation with improved, lighter two-wire cabling • Built-in rapid shutdown compliant (NEC 2014, 2017 & 2020) Efﬁcient and Reliable • Optimized for high powered 66-cell* modules • Highest CEC efﬁciency of 97.0% • More than a million hours of testing • Class II double-insulated enclosure • UL listed Smart Grid Ready • Complies with advanced grid support, voltage and frequency ride-through requirements • Remotely updates to respond to changing grid requirements • Conﬁgurable for varying grid proﬁles • Meets CA Rule 21 (UL 1741-SA) * The IQ7HS is required to support 66-cell modules. 2202 N Santiago St 01/25/23