|
BI 7.2.3-15 Apr-2014, Rev 8
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br /> +(; '5,9( 21 6(7 6&5(:
<br />6/,'( 72 '(6,5('
<br />/2&$7,21
<br />
<br />
<br />
<br />%27+ 6,'(6 2) 6/27 6(55$7('
<br />,7(0 1247<
<br />
<br />'(6&5,37,21
<br />%$6( 3/$7( 48,&. +22. :,'( 7
<br />0,//
<br />/$* 6&5(: +(; +($' [ 66
<br />48,&. +22. 9(57,&$/ 7 0,//
<br />6(7 6&5(: +(; 62&.(7 ; 66
<br />68%)/$6+,1* 48,&. +22. 9 %$6( ;
<br />; 0,//
<br />
<br />'2 127 6&$/( '5$:,1*6+((7 2)
<br />5$'
<br />6&$/( :(,*+7
<br />5(9
<br />$
<br />6,=(
<br />7,7/(
<br />'$7(
<br />'5$:1 %<
<br />',0(16,216 $5( ,1 ,1&+(6
<br />72/(5$1&(6
<br />)5$&7,21$/
<br />7:2 3/$&( '(&,0$/
<br />7+5(( 3/$&( '(&,0$/
<br />35235,(7$5<$1'&21),'(17,$/
<br />7+( ,1)250$7,21 &217$,1(' ,1 7+,6 '5$:,1* ,6 7+( 62/( 3523(57< 2) 48,&. 02817 39 $1< 5(352'8&7,21 ,1 3$57 25 $6
<br />$ :+2/( :,7+287 7+( :5,77(1 3(50,66,21 2) 48,&. 02817 39 ,6 352+,%,7('
<br />
<br />81/(66 27+(5:,6( 63(&,),('
<br />
<br />40)7+ 48,&. +22.)/$7 7,/(
<br />02817
<br />
<br />®Quick Hook – Flat Tile Mount QMFTH
<br />Notes:
<br />1) Thread must be embedded in a rafter or other structural roof member.
<br />2) See IBC for required edge distances.
<br />IMPORTANT: To maintain waterproo ng of substrate it is important to make sure the aluminum sub- ashing is properly placed over the base plate and under the
<br />course of paper above. If the paper above does not reach, due to layout, place an additional piece of roo ng paper over the sub- ashing and under the next course
<br />of paper above. (See instructions on reverse)
<br />Quick Hook USA Failure Test Results
<br />Average Ultimate Load Capacities (lbf) in Douglas Fir
<br />Con guration Source Document Pullout Compression Shear Parallel to
<br />Rafter
<br />Shear Perpendicular
<br />to Rafter
<br />Centered: All base plate sizes with hook positioned
<br />directly over the lag screws (see Appendix A & B of
<br />referenced report for test setup)
<br />AME Report #112640C "Quick Hook USA-Flat Tile
<br />Mount" with 1.5 Base Plate
<br />This report shows results for Quick Hook USA, both
<br />Flat and Curved Tile models, when the hook is posi-
<br />tioned directly over the lag screws
<br />876 685 1058 583
<br />Offset 4.5" Base Plate: 4.5" wide base plate with
<br />hook positioned at opposite end of base plate from lag
<br />screws (see Appendix A & B of referenced report for
<br />test setup)
<br />AME Report #112640C "Quick Hook USA-Curved Tile
<br />Mount with 4.5" Base Plate
<br />This report shows results for our Quick Hook USA-
<br />Flat Tile Mount
<br />1084 712 1219 532
<br />Offset 6" Base Plate: 6" wide base plate with hook
<br />positioned at opposite end of base plate from lag
<br />screws (see Appendix A & B of referenced report for
<br />test setup)
<br />AME Report #112640C "Quick Hook USA-Curved Tile
<br />Mount with 6" Base Plate
<br />This report shows results for our Quick Hook USA-
<br />Curved Tile Mount
<br />1246 692 1341 584
<br />BI 7.2.3-15 Apr-2014, Rev 8
<br />You are now ready for the rack of your
<br />choice. Follow all the directions of
<br />the rack manufacturer as well as the
<br />module manufacturer.
<br />All roo ng manufacturersÂ’ written
<br />instructions must also be followed
<br />by anyone modifying a roof system.
<br />Please consult the roof manufactur-
<br />er's specs and instructions prior to
<br />touching the roof.
<br />Remove the tile at selected location of the mount.
<br />Locate and mark the center of the rafter.
<br />Quick Hook
<br />Flat Tile Mounting Instructions - Rafter Installation
<br />Rest the base plate over center of rafter and mark
<br />center of holes. Drill two 7/32" pilot holes and ll
<br />with sealant compatible with roo ng material.
<br />Drive lag screws into rafter through the two holes
<br />to a solid, snug t. DO NOT over tighten lag screws,
<br />this may compromise their holding strength.
<br />Bolt the side-mounted rail of your choice to the
<br />hook, using the rail manufacturer's hardware.
<br />WARNING: Quick Mount PV products are NOT designed and should NOT be used for anchoring fall protection equipment.
<br />Slide hook into position on base plate. The hook
<br />must not overhang the side edges of the base
<br />plate. Tighten set screw with hex key.
<br />Proceed with weatherproo ng using three-course
<br />method or lapped paper method.* When using pa-
<br />per method, cut a piece of underlayment 18" wide
<br />to slide under the course above and over the sub-
<br /> ashing. If course above is too high, you must use ad-
<br />ditional underlayment to ensure proper overlapping.
<br />* For more details on underlayment waterproo ng please
<br />visit: http://www.quickmountpv.com/tile-waterproo ng
<br />Replace the tile above the hook. If necessary, notch
<br />the bottom of the tile to make space for the raised
<br />hook.
<br />Carefully clean the underlayment, then apply bead of
<br />compatible sealant in the shape of an upside down U
<br />on the backside of the sub- ashing and install ashing
<br />over mount. Fasten sub- ashing to deck with one roof-
<br />ing nail in each top corner. Do not nail bottom corners.
<br />®
<br />Installation Tools Required: stud nder, tape measure, utility knife, 3/32" hex key, drill with 7/32" bit, impact dril with 1/2" socket, caulking gun, one
<br />tube of sealant compatible with roo ng materials, roo ng bar, hand broom, stapler, 18" wide piece of underlayment or materials for 3-course method
<br />during deck ashing installation.
<br />notch
<br />The Quick Hook is designed for at and S-shaped curved tiles. Requires roo ng battens.
<br />1925 W Pendleton
<br />Ave - 10111215712/16/22
|