3110 & 3112 S Griset Pl - Plan - Laserfiche WebLink

Home Browse Search

All ideas, drawings,specifications shown herein are the property of West Coast Design Group and shall not be used, copied, reproduced, or disclosed to any person, firm or corporation, without the written consent of West Coast Design Group. Any infringement will be subject to legal action. The contractor shall verify and be responsible for all dimensions and conditions on the job and notify this office of any variations from dimensions and conditions shown herewith. Written dimensions take precedence over scaled dimensions. Mark Transmittal Set Date Description 01 02 03 12/19/2024 3/14/2025 3/27/2025 Building Corr. SHEET TITLE A-9 SHEET 20 PROJECT NO: STATUS: DRAWN BY: CHK'D BY: PROJECT: CLIENT: PLOT DATE: 3/27/2025 52-24 PLAN CHECK#:101122356 C : \ U s e r s \ j e r r y \ D o c u m e n t s \ D r a w i n g s \ R e s i d e n t i a l \ S a n t a An a Gr i s e t PI \ C D \ S a n t a A n a G r i s e t P I . p l n Submittal Door & Window Schedule ADU 3110 & 3112 S Griset Pl Santa Ana, CA 92704 Matthew Mallari & Natalie Nguyen PLANNING - DESIGN 41055 CHACO CANYON ROAD MURRIETA CA 92562 WEST COAST DESIGN GROUP DOOR ID D01 D02 D03 D04 D05 D06 D07 2D Plan Preview Door Elevation 5' 6' - 8 " 3' 6' - 8 " 9' 6' - 8 " 3' 6' - 8 " 3' 6' - 8 " 3' 6' - 8 " 7' 6' - 8 " TYPE Double Swing Swing Slider Swing Swing Swing Slider NOMINAL WIDTH 5'3'9'3'3'3'7' NOMINAL HEIGHT 6'-8"6'-8"6'-8"6'-8"6'-8"6'-8"6'-8" Door LEAF THICKNESS 1 3/4"1 3/8"1 3/4"1 3/8"1 3/8"1 3/8"1 3/4" LEAF MAT.Wood/Glass Hollow Core/Wood Hollow Core/Wood Solid Core/ Wood Hollow Core/Wood Hollow Core/Wood Hollow Core/Wood DOOR FRAME Wood Wood Wood Wood Wood Wood Wood Hardware Set 2 1 4 2 2 1 Accesories Fire Resistance Rating Unrated Unrated Unrated 20 Min Unrated Unrated Unrated Self Closing Self Latching Tempered SideLights N/A N/A N/A N/A N/A N/A N/A Decorative/Obscured Laminated Remarks DOOR SCHEDULE ID W01 W02 W03 W04 W05 W06 W07 2D Plan Preview Window Elevation Window Unit Size 5'×3'2'×2'5'×4'3'×3'3'×1'-6"5'×4'2'×2' Window Type Slider Fixed Slider Slider Slider Slider Fixed Panes Double Double Double Double Double Double Double Frame Material Wood Vinyl Wood Wood Wood Wood Vinyl Energy SHGC .23 .23 .23 .23 .23 .23 .23 U-Factor .30 .30 .30 .30 .30 .30 .30 Area 15.00 4.00 20.00 9.00 4.50 20.00 4.00 Tempered Decorative/Obscured Fire Rating Remarks WINDOW SCHEDULE DOOR NOTES: • DOORS SHALL BE JEN-WELD OR EQUAL • VERIFY DOOR TYPE, AND SWING WITH DRAWINGS • HEED MATERIAL MANUFACTURERS’ HANDLING AND APPLICATION INSTRUCTIONS. • PROTECT SURFACES FROM DIRT, MOISTURE, AND DIRECT SUNLIGHT • STORE IN A DRY LOCATION AND PROTECT FROM THE OUTSIDE ELEMENTS. • DOORS WITH GLAZING SHALL BE TEMPERED • VERIFY ROUGH OPENING REQUIREMENTS WITH DOOR MANUFACTURER FOR ROUGH FRAMING. • PROTECT FROM EXPOSURE TO DIRECT SUNLIGHT DURING STORAGE. • VERIFY DOOR GLAZING WITH TITLE 24 REQUIREMENTS BEFORE INSTALLATION. SEE TITLE 24 SHEETS. WINDOW NOTES: • WINDOWS SHALL BE MILGARD OR EQUAL • MAKE SURE OPERABLE WINDOWS ARE LOCKED PRIOR TO INSTALLATION. • HEED MATERIAL MANUFACTURERS’ HANDLING AND APPLICATION INSTRUCTIONS. • PROTECT ADHESIVE SURFACES FROM DIRT, MOISTURE, DIRECT SUNLIGHT AND FOLDING OVER ONTO THEMSELVES. • HANDLE IN VERTICAL POSITION; DO NOT CARRY FLAT OR DRAG ON FLOOR. • DO NOT PUT STRESS ON JOINTS, CORNERS OR FRAMES. • STORE WINDOW IN DRY, WELL-VENTILATED AREA IN VERTICAL, LEANING POSITION TO ALLOW AIR CIRCULATION; DO NOT STACK HORIZONTALLY. • PROTECT FROM EXPOSURE TO DIRECT SUNLIGHT DURING STORAGE. • INSTALL ONLY INTO VERTICAL WALLS AND WHEN CONDITIONS AND SHEATHING ARE DRY. • VERIFY WINDOWS MEET TITLE 24 REQUIREMENTS BEFORE INSTALLATION. SEE TITLE 24 SHEETS. 1. EACH PANE SHALL BEAR THE MANUFACTURER’S MARK DESIGNATING THE TYPE AND THICKNESS OF THE GLASS OR GLAZING MATERIAL. THE IDENTIFICATION SHALL NOT BE OMITTED UNLESS APPROVED AND AN AFFIDAVIT IS FURNISHED BY THE GLAZING CONTRACTOR CERTIFYING THAT EACH LIGHT IS GLAZED IN ACCORDANCE WITH APPROVED CONSTRUCTION DOCUMENTS THAT COMPLY WITH THE PROVISIONS OF THIS CHAPTER. SAFETY GLAZING SHALL BE IDENTIFIED IN ACCORDANCE WITH SECTION 2406.3. EACH PANE OF TEMPERED GLASS, EXCEPT TEMPERED SPANDREL GLASS, SHALL BE PERMANENTLY IDENTIFIED BY THE MANUFACTURER. THE IDENTIFICATION MARK SHALL BE ACID ETCHED, SAND BLASTED, CERAMIC FIRED, LASER ETCHED, EMBOSSED OR OF A TYPE THAT, ONCE APPLIED, CANNOT BE REMOVED WITHOUT BEING DESTROYED. TEMPERED SPANDREL GLASS SHALL BE PROVIDED WITH A REMOVABLE PAPER MARKING BY THE MANUFACTURER. 2. TEMPERED GLASS IS REQUIRED FOR: • ANY WINDOW LESS THAN 18 INCHES IN HEIGHT FROM A WALKING SURFACE. • ANY WINDOW LESS THAN 24 INCHES OF ANY DOOR. • ANY WINDOW OVER A BATHTUB OR SHOWER LESS THAN 5 FEET FROM THE FLOOR OF THE SHOWER OR BATHTUB. • ANY WINDOW WITHIN 40” OF A LOCKING DEVICE. • GLAZING IN AN INDIVIDUAL FIXED OR OPERABLE PANEL ADJACENT TO A DOOR WHERE THE NEAREST VERTICAL EDGE IS WITHIN A 24” ARC OF THE DOOR IN A CLOSED POSITION AND THE BOTTOM EDGE IS LESS THAN 60” ABOVE THE WALKING SURFACE. DOOR HARDWARE SET: 1. NO HARDWARE REQUIRED (DUMMY) 2. PRIVACY HARDWARE - LOCKSET THAT CAN BE LOCKED BY A BUTTON OR TURN PIECE ON THE INSIDE WITH NO KEY FUNCTION. 3. ENTRANCE - SINGLE OR DOUBLE CYLINDER WITH A KEY LOCK. VERIFY THICKNESS REQUIREMENTS WITH DOOR PANELS. (OWNER TO CHOOSE FINISH AND STYLE). 4. DEADBOLT - KEYED ENTRY WITH A BUTTON OR TURN KEY ON THE INTERIOR. 5. MORTISE SET - POCKET DOORS NOTE: OWNER TO SELECT ALL HARDWARE FINISH AND STYLE. G.C. TO PROVIDE THE OWNER WITH HARDWARE SETS FOR THE OWNER TO CHOOSE BEFORE ANY INSTALLATION.