|
93 SIGN COMPONENTS MANUAL (SAM)October 1, 2013
<br />4. These products may be secured in place in the end product by any means available.
<br />Class 2 Low Voltage Connectors, Model LVC2, LVC4, SNAP-KONEK 111, and STICK-KONEK.
<br />1. These devices are not suitable for interrupting the flow of current by connecting or disconnecting.
<br />2. These products are only suitable for connection to a Class 2 power source, Class 2 supply rated max. 15 Volts AC or max. 30
<br />Volts DC or less.
<br />3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage
<br />and energy limits.
<br />4. These products are suitable for use in dry, damp and wet locations.
<br />5. These products are not required to be enclosed or protected from the weather in the end product.
<br />6. Modules can be installed to interconnect leads in the field or pre-installed.
<br />7. These products may be secured in place in the end product by mechanical securement or double sided adhesive tape.
<br />8. For Model LVC2 and LVC4, suitable for connecting stranded wires which are 18, 20 or 22 AWG with compatible wire guide
<br />inserts.
<br />9. For Model SNAP-KONEK Ill, suitable for connecting single conductor per channel either AWM wires 18-24 AWG, or Power-
<br />Limited Circuit Cables type CL3P, CL3R, CL3, CLBX, CL2P, CUR, CL2, CL2X and PLTC.
<br />10. The Model STICK-KONEK base and button are used to join LED strips, LED bars, or LED leads wires.
<br />MAGTECH INDUSTRIES CORP
<br />5625-A S ARVILLE ST
<br />E314969
<br />LAS VEGAS, NV 89118
<br />Class 2 LED Module, Cat. No. LP12060P-08, LP12060P-09, LP12060P-10, LP12060P-11,LP12060P-12, LP24060P-22,
<br />LP24060P-23,LP24060P-24.
<br />1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to
<br />Class 2 output requirements for dc circuits.
<br />2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations.
<br />3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls,
<br />and minimum 2 inches spacing to top of enclosure.
<br />4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both
<br />primary and secondary circuits.
<br />MATRIX FRAME
<br />FLEVOWEG 27
<br />E351057
<br />2318 BZ LEIDEN, THE NETHERLANDS
<br />Class 2 LED Module, "Lightbox CREE XP LEDstrip".
<br />1. These products are suitable for use in Dry and Damp Locations Only and may only be supplied with a Class 2 power source with
<br />Current limit rated max. 2.5 Amps or less.
<br />2. These products are only suitable for connection to a Class 2 or LPS power source, rated 24 Volt DC or less.
<br />3. These products shall be mounted in equipment, which provide ·a suitable overall enclosure.
<br />4. A maximum of 4 Led strips are allowed to be mounted in a row, as detailed in the mounting instructions.
<br />5. These products may only be installed in a metal based enclosure (frame) that is able to transfer the heat that comes from the
<br />LEDs over the metal-core Printing Wiring Board into the ambient.
<br />MATRIX FRAME
<br />FLEVOWEG 27
<br />E358648
<br />2318 BZ LEIDEN, THE NETHERLANDS
<br />Class 2 LED driver box, Model A120606.
<br />1. The power supply has been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.
<br />2. The Class 2 output of the power supply is suitable for use in dry and damp locations only.
<br />3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls,
<br />and minimum 2 inches spacing to top of enclosure.
<br />4. These products shall be enclosed in the end product.
<br />5. These products are suitable for factory wiring only.
<br />6. The load powered by the Class 2 output of the power supply rated at max 30 VDC or less are suitable for use in dry, damp and
<br />wet locations.
<br />7. The suitability of strain relief, current leakage, and grounding tests shall be determined in the end-use product.
<br />8. AC input and output connectors are not polarized. Suitability shall be determined in the end use.
<br />MAXBRITE LED LIGHTING TECHNOLOGY LLC
<br />1740-B JUNCTION AVE.
<br />E313209
<br />SAN JOSE, CA 95112
<br />Class 2 LED Illumination Module, Cat. No. OTH-308X 10x18-01 Series, x: indicate the COLOUR: R-Red, Y-Yellow, B-Blue, G-
<br />Green, W-White, YO-Yellow Orange.
<br />1. These products are only suitable for connection to a UL Listed or Recognized maximum Class 2,12 V DC power source.
<br />2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 circuit
<br />limits.
<br />3. Class 2 LED module, OTH-308X 10x18-01 Series When units are connected to a Class 2 circuit, they are not to draw a total
<br />wattage of greater than the secondary or output rating of the Class 2 supply. Each module is rated 0.2A.
<br />4. These products are suitable for use in dry, damp or wet locations.
<br />5. These products are not required to be enclosed or protected from the weather.
<br />Class 2 LED Module, PL5050 Polar series, x: indicate the COLOUR; CW-Cool White, PW-Pure White; WW-Ware White; GL-
<br />Golden Yellow, RGB-RGB; Y-Bright Yellow: R-Bright Red; B-Vivid Blue; G-Mega Green; A-Aquamarine. POLAR X Series:
|