10180153_600 S. GRAND 600 - Plan

Home Browse Search

Ocfober 1, 2013 SIGN COMPONENTS MANUAL (SAM) 54 GEPS24-20, a temperature test is required when installed in an enclosure smaller than 13.5 by 6 by 4 inches, but the maximum temperature on the output transformer by thermocouple is 90°C 4. The output of these LED power supplies with Class 2 are acceptable for use in·a damp and wet locations. Power supplies with Class 2 outputs, Model GEXNPS30. 1. This component has outputs that qualify as being Class 2. 2. These components are intended for use in dry location ohly. 3. The itransformer employs a Class B (130) Insulation System. 4. These components shall be installed in compliance with the enclosure and mounting requirements of the ultimate application. 5. The maximum room ambient temperature permitted by the manufacture is 50(C. 6. A Temperature Test is required of the power supply installed in an enclosure that measures less than 13.5 by 6 by 4 inches. The maximum temperature on the output transformer by thermocouple is 110( C. Power supplies with Class 2 outputs, Models GEPS24-180U, GE 180/MVA/24T1 -C 1. The maximum measured output voltage, current and power at the output of these models was found in compliance with the limits for LPS output requirements and additionally evaluated to comply with Class 2 output criteria. 2. The transformer employ Class B insulation system. 3. Power Supply is intended for use in indoor Dry and Damp location only. 4. In the end product, power supply spacing to other heat producing components shall be minimum Pinches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure Adjacent power supplies shall be spaced at least 1 in.;end to end and 4 in. in any other direction 5. Input and Output leads are style 1316, rated 600 V, 105°C, VW-1. Minimum No. 18 AWG. The suitability of input and output connections shall be determined in each end use application. 6. The power supply was submitted and tested for a maximum ;manufacturer's recommended Tc point described in the table below. If adjacent LED power supplies are spaced closer than 1 in. end, to end or 4 in. side to side a temperature test shall be conducted in the end use product. Model Input Voltage. HZ Max. Case Ternp @ Tc, 'C Ambient 'C i GE180/MV/V24T1-C, GEPS24-100-277,60 80 60 180U LED Light Engine, Cat. Nos 1 110-WH-ZZ-TTK, 1110-RD-ZZ-TTK, catalog numbers where: "ZZ" representing assembly versibn: followed by: "TT" - Optional - represents the color temperaturei of the LEDs in degree "K" Kelvin. Cat. Nos. 1111 XX-ZZ-Y-TTK. catalog numbers may vary per nomenclature.: "XX" representing color: R[) RC, YG, GL, SB, BL, WH, YA, VVW, GR, PO; "ZZ" fepresenting assembly version: "Y" representing number of LE)s; followed by: "TT" - Optional - represents the color temperature of the LEDs in degree "K" Kelvin. 1. These products are only suitable for connection to a Class 2 power source. 2. When units are connected to a Class 2/"LPS" circuit, they are n0t to draw a total wattage of greater than the secondary or output rating of the Class 2/"EPS" supply. 3. These products are suitable for use in dry, damp and wetlocations. 4. The suitability of the LED Light Engine mounting means shall be determined inlthe end-ose application. 5. The suitability of the LED Light Engine to be used without an additional electrical enclosure shall be determined in the end-use application. 6. These products described in this section may be cut into segments per manufacture insulation instructions. 7. Units may be provided with UYMR2,3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of Use- as defined in the Sign Components Manual. LED Driver with Class 2 Output, Models GEPS1'20-60U, GEPS24D-80U. 1. These LED Drivers have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 2. These products are provided with thejollowing elear-ical ratings: Model No.Input Voltage (V Input Reg Input Curfent Output Voltage Output Curreht Output ac) (HZ)(A)(V dc) (A) Power (W) GEPS24D-80U 100-277 50/60 1.1 24 3.3 - 80 GEPS 12D-60U 100-277 50/60 0.85 12 - 5.0 3 --60 3. The load powered by the Class 2 output of the LED drivers are suitable for use in dry, damp and wet locationi 4. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 5. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less than 4 inches (102mm) apart when arranged otherwise. 6. These products shall be enclosed in the end product. 7. The unit is intended for being used in permanently wired signs. 8. The suitability of output leads, rated No. 24 AWG minimum, rated 80°C minimum, 600 V, shall be determined in end product use. 9. These units may provided with Dimming Input (Purple and Gray wires) to control output cur.rent range, the suitability shall be determined in each end-use application. 10. These products are intended for use in dry and damp locations LED Driver with Class 2 Output, Model 1110PS-60S. 1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted on page 1. 2. These LED drivers are provided with Class 2 output. 3. These LED drivers are intended to be operated in a maximum ambient (Ta) noted as below: -_ Model | Ta (°C) LD-60-UV-1214V 1 46 4. These LED drivers are intended fofuse in dry and damp locations except that models LD-60-UV-1214\/ and LD-60-UV-1214\/- SC are suitable for dry location only. 5. These LED drivers are provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a suitable enclosure shall be considered in the end product.