10180154_1915 W. FIRST C - Plan - Laserfiche WebLink

Home Browse Search

October 1, 2013 SIGN COMPONENTS MANUAL (SAM)134 1. These products are only suitable for connection to a Class 2 power source, rated 30 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 30 V DC. 3. These products are each rated max. 100 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations when rated maximum 30 VDC. 5. These products are not required to be enclosed or protected from the weather in the end product when rated 30 VDC or less. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered. LED Strips, Cat. No. 701174,701181 and 701195 with suffix -R, -Y, -A, -B, -W, or -G followed by -1" through -24". 1. These products are only suitable for connection to a UL Listed or Recognized Class 2,24 volt AC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products may be cut into segments through a black mark provided on the printed wiring board. No other cut across the board is permitted. 4. Cat. No. 701174 is rated for 4.2 watts per foot, Cat. No. 701181 is rated for 9.2 watts per foot and Cat. No. 701195 is rated at 1.5 Watts per foot. The total number of feet of each type and inches for the inch unit are not to produce a total wattage of greater than 60 watts per Class 2 circuit. 5, These products are suitable for use in dry, damp and wet locations. 6. These products are not required to be enclosed or protected from weather. Class 2 LED Module, Cat. No. 701946-XXYYYYUZZZ series, where XX, YYYYYY and ZZZ may be replaced with any alphanumeric characters or blank. 1. These products are suitable for use in dry, damp and wet locations and supplied only with a Class 2 power source rated 24 Volt DC or less. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. Class 2 power supply, Model 701285. 1. Power supply is intended to power LEDs in signs. 2. Power supply model is intended for permanent connection only. 3. These units are suitable for use in dry location without a need for an additional enclosure and in damp locations when installed inside a sign that complies with the Exclusion of Water Test in UL 48. 4. If the power supply output wiring is extended longer than the 5 foot leads provided, the spliced connections shall be made inside a Listed junction box suitable for the application included with proper grounding. Class 2 power supply, Cat. Nos. 701349, 701351. 1. Power supply models 701349 and 701351 are intended to power LEDs in signs. 2. Power supply model 701349 and 701351 are intended for permanent connection only. 3. These units are suitable for use in dry location without a need for an additional enclosure and in damp locations when installed inside a sign that complies with the Exclusion of Water Test in UL 48. 5. These power supplies have two outputs. The Class 2 output circuits are not to be conductively connected to each other in the sign by wiring or other type of component. 6. The maximum rated output power for Model 701349 is 42 watts at each Class 2 output. The maximum rated output power for Model 701351 is 60 watts at each Class 2 output. Class 2 power supplies, Models 701507-MOD, 701507-MOD277 (AD060S277/347-SLN). All may be followed by alphanumeric sumx. 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on primary circuit. 5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product. 6. When not marked for Dry and Damp Locations Only the power supply primary bracket shall be provided with min. 3.5 threads and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3.5 threads, the liquid tight shall be provided with watertight fitting Listed (QCRV) 1/2 inch, liquid tight conduit fittings. 7. The suitability of grounding connection shall be determined in the end-use product. Class 2 power supply, Model 701680. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief on input lead construction and Impact Tests have not been investigated. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of each unit is V-2, and the necessity of additional fire barriers shall be determined in end product. 7. Multiple power supplies shall be spaced at least 25mm (1 in.) end to end or 102mm (4 in.) in other directions. If lesser spacings are used, then the Temperature Test shall be conducted in the end use product. For reference the maximum enclosure (case) temperature on the power supply was 90°C when tested at 58.4° ambient. Class 2 power supply, Model 701680-MW. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output.