10180553_3814 S. BRISTOL B - Plan

Home Browse Search

October 1, 2013 SIGN COMPONENTS MANUAL (SAM) 78 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105(C. Output leads are Style 1430, No. 18 AWG, rated VW-1,300 V, 105°C. The suitability of the input and output connections shall be determined in each end use application. 5. Strain Relief and Impact Tests have not been. investigated. The suitability of the enclosure as ultimate enclosure shall be determined in the end-use application. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of unit is V-2 and the necessity of additional fire barriers shall be determined in end product. 7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 8. The output of the power supply exceeds the Class 2 output limits. This shall be considered in the end product. KBJ SIGN INC 1800 W ADAMS BLVD E350092 LOS ANGELES, CA 90018 Class 2 LED Modules, KPL, FPL, KR3. 1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy limited circuit and is rated greater than 12V DC. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. LED Class 2 Module, KBJ-301, KBJ-303, KBJ-301-S, KBJ-303-S, KBJ-3RGB, KBJ-401, KBJ-403-S, KBJ-4RGB, 1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volts DC or less. 4. These products are not required to be enclosed or protected from the weather in the end product. 5. These products may be secured in place in the end product by any means available. KEYSTONE TECHNOLOGIES LLC E356111 PO BOX 246 AMBLER, PA 19002 Class 2 LED Modules, Models KTLD-80-1-24V, KTLD-60-1-12V, KTLD-60-1-244 KTLD-60-1-24\/-SCI KTLD-60-UV-244 KTLD- 60-UV-24V-SC, KTLD-60-UV-24V-DIW, KTLD-60-UV-1214V, KTLD-60-UV-1214V-SC. 1. These LED drivers have been evaluated using resistive load resulting in the electrical input and output noted on page 1. 2. These LED drivers are provided with Class 2 output. 3. These LED drivers are intended to be operated in a maximum ambient (Ta) noted as below: Model Ta.(°C) KTLD-80-1-24V 40 KTLD-60-1-12V 40 KTLD-60-1-24V 40 KTLD-60-1-24\ASC 40 KTLD-60-UV-24V 40 KTLD-60-UV-24V-SC 40 KTLD-60-UV-24V-DIW 52 KTLD-60-UV-1214V 40 KTLD-60-UV-1214V-SC 40 4, These LED drivers are intended for use in dry and damp locations except that models KTLD-60-UV-1214V and KTLD-60-UV- 1214\ASC are suitable for dry location only. 5. These LED drivers are provided with 18 AWG AWM input and output leads. The suitability of the wiring and the need for a suitable enclosure shall be considered in the end product. 6. These LED drivers are intended to be operated on a maximum 20 A branch circuit. 7. The need of the grounding means shall be determined in the end product. 8. These LED drivers shall be enclosed within a suitable end product enclosure. 9. For model KTLD-60-UV-24\ADIW, the conduit knockout test was not conducted. The suitability is to be determined in end product. 10. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 11. In the end product, LED Drivers shall be located not less than 1 inch (25.4 mm) apart when arranged end-to-end, and not less than 4 inches (102 mm) apart when arranged otherwise. KOLEDO INTERNATIONAL BV EKKERSRIJT 7051 5692 HB SON EN BREUGEL, THE NETHERLANDS E346915 11