Laserfiche WebLink
ESR-4266 <br />ldcst widely Aaep!ed and 'r rs rrv.1 <br />TABLE 1—SETTING INFORMATION <br />CITY OF SANTA ANA <br />Planning and Building Agency <br />Page 7 of 18 <br />Approved <br />E R7a11 T I"�S ANC E <br />Setting <br />Unit <br />Nominal <br />anchor <br />diameter <br />in. <br />information <br />Sym' <br />S <br />1/4 <br />3/8 <br />1/2 <br />518 <br />3/4 <br />1 <br />Nominal bit <br />diameter <br />d, <br />In <br />1/4 <br />3/8 <br />112 <br />5/8 <br />3/4 <br />1 <br />Effective min. <br />In. <br />1-1/2 <br />1-1/2 <br />2 <br />2-1/2 <br />1-1/2* <br />2 <br />2-1/2 <br />3-1/4 <br />2-3/4 <br />3-1/4 <br />4 <br />3-1/ <br />/ <br />4- i4 <br />4 <br />5-3/4 <br />embedment <br />he <br />(mm) <br />38 <br />38 <br />(51 <br />64 <br />(38 <br />51 <br />(64) <br />83 <br />70 <br />83) <br />102) <br />(83 <br />121 <br />102 <br />146 <br />Nominal <br />in. <br />1-3/4 <br />1-7i8 <br />2-1/2 <br />3 <br />2' <br />2-1/2 <br />3 <br />3-3/4 <br />3-1/4 <br />3-3/4 <br />4-1/2 <br />4 <br />4-1/2 <br />5-1/2 <br />4-5/8 <br />6-3/8 <br />embedment <br />h_ <br />(mm) <br />(44) <br />(48) <br />(64) <br />76) <br />(51) <br />64) <br />(76) <br />(95) <br />(83) <br />(95) <br />114) <br />(102) (114) <br />(140) <br />(117) <br />(162) <br />Min. hole depth <br />h <br />In. <br />2 <br />2 <br />2-3/4 <br />3-1/4 <br />2-1/4' <br />2-3/4 <br />3-1/4 <br />4-1/4 <br />3-3/4 <br />4-1/4 <br />4-3/4 <br />4-1/4 4-3/4 <br />5-3/4 <br />5 <br />6-3/4 <br />(mm) <br />51) <br />51) <br />70 <br />(83 <br />57) <br />70 <br />(83 <br />(108) <br />(95) <br />108 <br />(121 <br />(108 <br />121 <br />(146) <br />(127) <br />(171) <br />Installation <br />ft-lb <br />4 <br />30 <br />50 <br />40 <br />110 <br />185 <br />torque <br />T.,:! <br />Carbon steel' <br />(Nm) <br />(5) <br />(41) <br />(68) <br />(54) <br />(149) <br />(251) <br />Installation <br />ft-lb <br />6 <br />30 <br />40 <br />60 <br />125 <br />185 <br />torque <br />T-,. <br />Stainless steel' <br />(Nm) <br />(8) <br />(41) <br />(54) <br />(81) <br />(169) <br />(251) <br />Fixture hole <br />dh <br />In. <br />5/16 <br />7116 <br />9/16 <br />11/16 <br />13/16 <br />1-1/8 <br />diameter <br />(mm) <br />(7.9) <br />(11.1) <br />(14.3) <br />(17.5) <br />(20.6) <br />(28.6) <br />Design information for h r= 1-1/2 is only applicable to carbon steel (CS) KB-TZ2 bolts. <br />collar UNC thread <br />mandrel `�? dog <br />expansion element J bolt I�—� <br />washer J hex nut <br />FIGURE 1—HILTI CARBON STEEL KWIK BOLT TZ (KB-TZ2) <br />FIGURE 2—HILTI KB-TZ2 INSTALLED <br />TABLE 2—LENGTH IDENTIFICATION SYSTEM (CARBON STEEL AND STAINLESS STEEL ANCHORS) <br />Length ID marking on bolt <br />A <br />B <br />C <br />D <br />E' <br />F <br />G <br />H <br />I <br />J <br />K <br />L <br />M <br />N <br />O <br />P <br />Q <br />R <br />S <br />T <br />U <br />V <br />W <br />head <br />Length of <br />From <br />1 %2 <br />2 <br />2% <br />3 <br />3Yz <br />4 <br />4%, <br />5 <br />5% <br />6 <br />6',% <br />7 <br />7Y: <br />8 <br />8'/2 <br />9 <br />9%: <br />10 <br />11 <br />12 <br />13 <br />14 <br />15 <br />anchor, (- , <br />Up to but not <br />(inches) <br />including <br />2 <br />2'/z <br />3 <br />3%: <br />4 <br />41/25 <br />5'/z <br />6 <br />654 <br />7 <br />7%2 <br />8 <br />8% <br />9 <br />9',-2 <br />10 <br />11 <br />12 <br />13 <br />14 <br />15 <br />16 <br />For SI: 1 inch = 25.4 mm. <br />"ly diameter anchors with length of 3'12 are identified with an ohm (la) ID marking on the bolt head, <br />'arbon Steel <br />iinole Notch <br />Length <br />Identification <br />Code <br />Stainless Steel 304 <br />Double Notch <br />Length <br />Identification <br />Code <br />Stainless Steel 316 <br />Triple Notch <br />Length <br />Identification <br />Code <br />FIGURE 3—BOLT HEAD WITH LENGTH IDENTIFICATION CODE AND KB-TZ2 HEAD NOTCH EMBOSSMENT <br />