10180596_521 W. 17TH - Plan - Laserfiche WebLink

Home Browse Search

135 SIGN COMPONENTS MANUAL (SAM)October 1,2013 2. Theload powered,by theiCIass 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and wet locations. 3. In the end product. power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewails, and minimum 2 inches spacing to top of enclosure. 4. These, prof!9Rtiareerovided-fve following electrical ratings: Input - _Output Model .Vac A Hz Vdc A 01 701680-MW 100-240 0.55 50/60 12 1.67 1 5. These products shall be enclosed in the end product. 6 These power supplies are suitable for use in dry and damp locations. Class 2 power supply, Model 701681. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3 Input leads are Style 1015, No. 18 AWG, rated VW-1,600 V, 105'C. Output leads are Style 1430, No. 18 AWG„rated VW-1, 300 V, 105'C. The suitability of the input and output connections shall be determined ih each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated on input lead construdtion. The suitability of the enclosure as ultimate enclosure shall be determined in the end-use application. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of the polymeric enclosure is V-0 and the necessity of additional fire barriers shall be determined in end product. 7. In the end product. power supply spacing to other heat producing components shall be minimum i2 inches spacing to,sidewalls, and minimum 2 inches spacing to top of enclosure. Class 2 power supplies. Model 701495. 1. These power supplies have been evaluated te Class 2 output requirements for dc circuits with a rriaximum of four Class 2 outputs. 2. These power supplies are only suitable for use in dry, damp and wet locations. 3. ln the end product, power supply spacing to other heat producing components shall be minimum 2 ihches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Class 2 power LED Lighting Strip, 701912-QQXXYYZZZ series, where QQ represents length, XX represents tbe LED color temperature, YY represents configuration and ZZZ represents the LED drive current. 1. These products are only suitable for connection to a Class 2 power source, rated 24VDC. 2. These products have not been evaluated for use when connected td a power source thatdoes not comply with Class 2 voltage and energy limits and which is rated greater than 24VDC. 3. VVhen units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated class 2. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or outlihe lighting, the need to conduct a temperature test shall be considered. Class 2 "Dimming Control Knob" potentiorneter, Model 701843. 1. These products are only suitable for connection to the output of a UL Listed or Recoghized Class 2 power supply rated max 12 VDC. 2. These products are suitable for use in dry and damp locations. 3. These products are suitable for factory wiring only. 4. These products are 1 Kohm potentiometers intended for connection to max 12 VDC Class 2 power supply that drops the voltage to a 0-10 V signal to feed into the PWM dimmer. Class 2 LED Modules, Cat. No. 701960-XXYYYZ Series, where XX, YYY, and Z may be replaced with any alphanumeric character or blank. 1. These products are suitable for use in dry, damp and wet locations and supplied only with a Class 2 power source irated 24 Volt DC or less. 2. When units are connected to a Class 2 circuit, they are not t0 draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. Class 2 power supplies, Models 701507-60W1 -JV and 701507-60W1-CT. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 2. These products are provided with the following electrical ratings: Output Output Frequency Voltage Current Model Number Input Voltage M Input Current (A)(Hz)¢Vdc)(mA) 701507-60W1 -JV,100-240 0.85 50/60 12 0-500 701507-60W1-CT 3. In the end product, power supply spacing to other'heat producing components shall be at least 25.4 mm (1 in) from end to end and 101.6 mm (4 in) from side to side. 4. These products shall be enclosed in the end product. 5. These products are suitable for factory wiring only. 6. These products are intended for use in a dry oridamp locations only. 7. The suitability of input/output leads and the wring shall be determined in end product use. SPARTECH PLASTICS E202184