10180921_3725 S. GARNSEY - Plan - Laserfiche WebLink

Home Browse Search

2 STRINGS OF 11 MODULES SMX CAPITAL: SMX250P, 250W TOTAL OUTPUT: 5,500 WATTS - (4) #10 AWG USE-2 (1) #6 BARE CU EGC @e INVERTER 1 SMA AMERICA: SB-5000TL-US-22 240VAC WITH INTEGRATED DC DISCONNECT UL 1741 LISTED, GFP. (3) #10 THHN/THWN-2 (1) #8 THHN/THWN-2 GROUND 3/4" EMT CONDUIT MAX CURRENT: 27.5A NEW 200 AMP ELECTRICAL SERVICE ENTRANCE AND LOAD CENTER 81-DIRECTIONAL UTILITY METER 240V 200A L.ze-J 15A FUSED DC DC DISCONNECT 1 -(4) #10 THHN/THWN-2 (1) #8 THHN/THWN-2 EGC 3/4" EMT CONDUIT 4 Ulei n-RON-1 111PHOTOVOLTAIC SYSTEM \ KILOWATT-HOUR METER \ 1004240VAC (TYP) \ C FUSIBLE AC DISCONNECT ) 2P30A 240V 3- ® ioA .I- 1,-. ' .39 2P200A 2P2 UTILITY GRID 120/240V WIRE TYPE SHALL BE 90° C WET AND CONTINUOUS RATED L SPS OUTLET MAX 120V/12A 150OW (TYP EACH INVERTER) A NORMALLY INERACTIVE SOLAR PHOTOVOLTAIC SYSTEM SHALL BE PERMITTTED TO OPERATE AS A STAND-ALONE SYSTEM TO SUPPLY LOADS THAT HAVE BEEN DISCONNECTED FROM ELECTRICAL PRODUCTION AND DISTRIBUTON NETWORK SOURCES (CEC, NEC 690.61). SINGLE PHASE W BUILDING GROUNDING ELECTRODE NOTES:SYSTEM OUTPUT:BACKFED BREAKER SHALL BE POSITIONED AT - 1. ALL PV SYSTEM COMPONENTS SHALL BE USED BY A RECOGNIZED TESnNG AGENCY (i.e., UL 1741, ETC) 2. WIRING MATERIALS SHALL BE SUITABLE FOR lHE SUN EXPOSURE AND WET LOCATIONS. FIELD APPUED PROTECTIVE COATINGS ARE NOT ACCEPTABLE. 3. WHERE THE TERMINAL OF THE DISCONNECTING MEANS MAY BE ENERGIZED IN THE OPEN POSITION, A WARNING SIGN SHALL BE MOUNTED ON OR ADJACENT TO THE DISCONNECTING MEANS HAVING THE FOLLOWING WORDS: "WARNING-ELECTRIC SHOCK HAZARD, DO NOT TOUCH TERMINALS. TERMINALS ON BOTH UNE AND LOAD SIDES MAY BE ENERGIZED IN THE OPEN POSInON" 4. SIGNS SHALL BE POSTED ADJACENT TO EACH PV DISCONNECT AND INVERTER TO INDICATE "PHOTOVOLTAIC SYSTEM" 5. ALL PV MODULES AND ASSOCIATED EQUIPMENT AND WIRING MATERIAL SHALL BE PROTECTED FROM PHYSICAL DAMAGE. 6. ALL FIELD INSTALLED JUNCTION, PULL AND OUTLET BOXES LOCATED BEHIND MODULES OR PANELS SHALL BE ACCESSIBLE DIRECTLY OR BY DISPLACEMENT OF A MODULE(S) OR PANEL-(S) SECURED BY REMOVABLE FASTENERS. 7. EACH SIDE OF A POWER TRANSFORMER SHAU BE CONSIDERED AS PRIMARY AND PROTECTED IN ACCORDANCE WITH CEC 2013. 8. REMOVAL OF INVERTER OR OTHER EQUIPMENT SHALL NOT DISCONNECT THE BONDING CONNECTION BETWEEN THE GROUNDING ELECTRODE CONDUCTOR AND THE PHOTOVOLTAIC SOURCE AND/OR OUTPUT CIRCUIT GROUNDED CONDUCTOR. 9. THE CIRCUIT CONDUCTORS AND OVERCURRENT DEVICES SHALL BE SIZED TO CARRY NOT LESS THAN 125% OF THE MAXIMUN CURRENT AS CALCULATED IN CEC 2013. 10. THE OVERCURRENT PROTECTION OF OUTPUT CIRCUITS WITH INTERNAL CURRENT UMInNG DEVICES SHALL BE NOT LESS THAN 125% OF THE MAXIMUM UMITED CURRENT OF THE OUTPUT CIRCUIT. THE CONDUCTORS IN SUCH AN OUTPUT CIRCUIT SHALL BE SIZED IN ACCORDANCE WITH CEC 2013. 11. PHOTOVOLTAIC SOURCE ciRCUITS, OUTPUT CIRCUITS, INVERTER OUTPUT CIRCUITS AND EQUIPMENT SHALL BE PROTECTED IN ACCORDANCE WITH THE REQUIREMENTS OF THE CEC 2013. 12. MODULE FRAMES AND RACKING SYSTEMS SHALL BE GROUNDED AT UL-USED LOCAnON PROVIDED BY THE MANUFACTURER USING UL USED GROUNDING LUGS. THE REMOVAL OF ONE PANEL- SHALL NOT INTERRUPT THE CONTINUITY OF THE GROUNDING SYSTEM FOR THE REST OF THE PANELS OR RACKING SYSTEM. CEC 2013 13.ALL CEC REQUIRED PV SIGNAGE (690.17, 690.53, 690.56, 705.10) WILL BE POSTED. 14.ALL GROUNDING ELECTRODES SHALL COMPLY WITH REQUIREMENTS CEC 250.32 DC (STC) RATING: 5.5kW (22) SMX CAPITAL: SMX250P, 250 WATT MODULES (1) SMA AMERICA: SB-5000TL-US-22 INVERTER PV SYSTEM CALCULATIONS: DC SIDE MAXIMUM DC SYSTEM VOLTAGE: 37.91V x 11 x 1.12 = 467.1V MAXIMUM PER DC SOURCE CIRCUIT CURRENT: 8.84A x 125% x 125% = 13.8A AC SIDE MAXIMUM AC SYSTEM VOLTAGE: 240V MAXIMUM AC TOTAL SYSTEM CURRENT: 22 x 1.25= 2UA MODULE INFORMATION: SMX CAPITAL SMX250P, 250W PEAK POWER: 250 WATTS Voc: 37.91 Vdc Isc: 8.84A Vpm: 30.11 Vdc Imp: 8.30A MAX SERIES FUSE RAnNG: 20A INVERTER INFORMATION SMA AMERICA: SB-5000TL-US-22 Compliance: IEEE-1547, UL 1741. DQ DC MAXIMUM VOLTAGE - 600V MAXIMUM INPUT CURRENT -30A/15A PER MPPT PEAK POWER TRACKING VOLTAGE-175-480V OP(125V--500V) PV START VOLTAGE - 125V AC MAXIMUM OUPTUT POWER - 5000 wotts OPERATING RANGE, UnUTY VOLTAGE - 211 - 264V @ 240V MAXIMUM CONRNUOUS OUTPUT CURRENT - 22A @ 240V FREQUENCY OPERATING RANGE - 60 Hz / 59.3 - 60.5 Hz MAXIMUM EmCIENCY - 97.1% @ 240VAC THE OPPOSITE (LOAD) END FROM THE INPUT FEEDER LOCAnON OR MAIN CIRCUIT LOCAMON SIGNAGE NOTES: ALL LABELS WILL BE ON RESISTANT MATERIAL SUITABLE FOR THE ENVIRONMENT. ALL LABELS SHALL HAVE A RED BACKGROUND WITH WHITE LETTERING. 0 0 WARNING SOLAR PHOTOVOLTAIC CONNECTION DUAL VOLTAGE SYSTEM AC DISCONNECT PHOTOVOLTAIC CONNECTED DUAL VOLTAGE SYSTEM RATED AC OUTPUT CURRENT:RATED AC OUTPUT CURRENT, 22 AMPS 22 AMPS NOMINAL OPERATING AC VOLTAGE:NOMINAL OPERATING AC 240 VOLTS VOLTAGE: 240 VOLTS SOLAR BREAKER ® DO NOT RELOCATE PV Solar DC Disconnect WARNING ELECTRIC SHOCK HAZARD DO NOT TOUCH TERMINALS CAUTION: SOLAR ELECTRIC SYSTEM CONNECTED THE LOAD SIDES MAY BE ENERGIZED TERMINALS ON BOTH THE LINE AND IN THE OPEN POSITION @ OPERATING CURRENT•16.6A WARNING OPERATING VOLTAGE,33121V ELECTRICAL SHOCK HAZARD. THE DIRECT CURRENT aRCUIT CONDUCTORS OF THIS PHOTOVOLTAIC MAXIMUM SYSTEM VOLTAGE, 467.1V POWER SYSTEM ARE UNGROUNDED BUT MAY BE SHORT CIRCUIT CURRENT,22.lA ENERGIZED WATH RESPECT TO GROUND DUE TO LEAKAGE PATHS ANQZOR GROUND FAULTS. » r-LU C- LOAD CALCULATIONS <i< 120% OF 200A = 240A 5 <OPV INPUT BREAKER = 30A J 0<£MAIN BREAKER UTILITY = 200A TOTAL SUPPLY AMPS = 30A + 200A = 230A »c/i zCo<C LO TO BE PLACED ON ALL INTERIOR & EXTERIOR CE (\1<DC CONDUITS, RACEWAYS, ENCLOSURES, CABLE h 1- ASSEMBLES, EVERY 10 FEET, AT TURNS AND 11 Z ABOVE AND BELOW PENETRATONS AND ALL 15 4 DC COMBINER AND JUNCTION BOXES Z 0 CAUTION: SOLAR ELECTRIC < SYSTEM CONNECTED & QC 1.LENERGIZED ® IF A GROUND FAULT IS INDICATED, THE NORMALLY GROUNDED CONDUCTORS MAY BE ENERGIZED AND UNGROUNDED Issue Date 3-10-2014 Drawing 1-LINE Sheet No. PV-4