|
69 SIGN COMPONENTS MANUAL (SAM)October 1, 2013
<br />4. The suitability of the mounting means shall be determined in the end-use application.
<br />5. LED modules described in this section may be cut into segments per the manufacturer's installation instructions.
<br />6. Units may be provided with Recognized Component (UYMR2), 3M type VHB double-sided adhesive tape. The tape must be
<br />utilized per the "Conditions of Use" as defined in the Sign Components Manual.
<br />7. A heatsink or a means to draw heat away from the Printed Wiring Board shall be provided in the end-use application.
<br />Diffuser Panels, Cat. Nos. IEP1, IEP2, IEP3, and IEP4.
<br />1. Cat. nos. IEP1, IEP3, IEP4 are suitable for use in dry, damp and wet locations. Cat. no. IEP2 is suitable for use in dry locations
<br />only.
<br />2. The panels are suitable for use as a rigid non-enclosure rated sign body, awning, face or decorative application.
<br />3. Panels have not been investigated for use as an enclosure of live parts, insulating barrier accessibility barrier, connection of
<br />conduit or component mounting or support.
<br />4. Panels are flame class rated HB.
<br />5. Cat. no. IEP1 rated 50'C for clear only when min 1.0 mm thick and rated 90°C for all colors when min 1.5 mm thick.
<br />6. Cat. no. IEP2 rated 50°C for all colors when min 1.5 mm thick.
<br />7. Cat. no. IEP3 rated 90°C for clear only when min 1.5 mm thick.
<br />8. Cat. no. IEP4 rated 80°C for all colors when'min 0.75 mm thick and 1156C for all colors when min 1.5 mm thick.
<br />INTERNATIONAL LIGHT TECHNOLOGIES INC
<br />10 TECHNOLOGY DR
<br />E332029
<br />PEABODY, MA 01960
<br />LED Class 2 Module, Model No. designated 1*2, 2X2.
<br />1. These components are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory·Class 2
<br />power supply.
<br />2. These components have not been evaluated for else when connected to a power source that does not comply with Class 2
<br />requirements.
<br />3 Lead wires are not Listed Class 2 cable. Therefore leads must be enclosed in a sign housing, wireway, raceway, or electrical
<br />enclosure.
<br />4. Components are suitable for use in dry, damp and wet locations.
<br />LED Class 2 Module, Cat. Nos. ILT-PC-1 X2-[+1, ILT-PC-2)(2-[+1.
<br />[+] - May be any alphanumeric characters to represent color and number of LED per module.
<br />1. These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less.
<br />2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy
<br />limited circuit and is rated greater than 15 V DC.
<br />3. These products are each rated max. 1.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a
<br />total wattage of greater than the secondary or output rating of the Class 2 supply.
<br />4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 VoJts DC or less.
<br />5. These products are not required to be enclosed or protected from the weather in the end product.
<br />6. These products may bee secured in place in the end rproduct by any means available.
<br />INTERONE
<br />55-1 DEOKGYE-DONG
<br />YANGJU-SI, GYEONGGI-DO
<br />E349550
<br />482-050 REPUBLIC OF KOREA
<br />LED Class 2 Module, Model Z303, Z301.
<br />1. These products are only'suitable for connection to a Class 2 power source rated 12 Volt DC or less.
<br />2. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output
<br />rating of the Class 2 supply.
<br />3. These products are suitable for use in dry, damp and wetlocations with supply sources rated at 12 Volts DC or less.
<br />4. These products are not required to be enclosed or protected from the weather in the end product.
<br />5. These products may be secured in place in the end product by any means available.
<br />LED Class 2 Module, 2101 K, Z103 K, Z201 K, Z201 3, Z201 T, Z203 K, Z203 SPO, Z203 S, Z203 TPO, Z203 T, 2203 LPO,
<br />Z203 LZ203 F, Z301 MTPO, 2301 K, Z301 S, Z301 LS, Z301 L, Z301 BB, Z303 K, Z303 SPO, Z303 S, Z303 LSPO, Z303 LS,
<br />Z303 LPO, Z303 L, 2303 FP, 2303 P, Z303 FC, Z303 C, Z303 KF, Z303 F, 2303 BB, Z401 K, Z401 S, 2401 BB, 2403 K, Z403
<br />SPO, 2403 S, Z403 KF, Z403 F, Z403 FP, Z403 P, Z403 FC, Z403 C, Z403 BB, 2P PO, 3P PO, 3P K, STPC, STAL.
<br />1. These products are only suitable for connection to a Class 2 power source fated 12 Volt DC or less.
<br />2. When these units are connected to a Class 2 circuit, they are notto draw a total wattage of greater than the secondary or output
<br />rating of the Class 2 supply.
<br />3. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12' Volts DC or less.
<br />4. These products are not required to be enclosed or protected from the weather in the end product.
<br />5. These products may be secured in place in the end product by any means available.
<br />INTERTEK CORP E307120
<br />4TH FL, 81 HSIN TAI-WU RD, SEC 1
<br />HSIN-CHIH, TAIPEI HSIEN 221 TAIWAN
<br />Class 2 LED Power Supply, Models APP200AC-12, APP200AC-15, APP200AC-24, APP200AC-30.
<br />1. These power supplies have not been provided with a suitable enclosure. In the end product these units shall ibe enclosed
<br />2. When used in a cord-connected products, the need for conducting a leakage current test shall be consi ered in the end
<br />product.
<br />3. The product was tested for use at the maximum ambient temperature (Tma) of 60°C permitted by the manufacturer's
<br />specification. This product will need to be temperature tested in the end product'and ambient cannot exceed 60°C.
<br />These components are suitable for use in damp locations.
|