10181386_1308 W. EDINGER - Plan - Laserfiche WebLink

Home Browse Search

January 4, 2010 SIGN COMPONENTS MANUAL (SAM) 20 4. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provid*€11;Gth a means to prevent. billowing 5. The mounted assembly of sign face material in these tensioning systems shall comply with the electrical and thermal spacing requirements of UL 48. 6. These clips have been determined to be suitable with any R/C Flexible Sign Faceaterial of min. 0.020 inches (0.51 mrn) thick, suitability for use with a material of lesser thickness shall be determined in te end product. ABLE APPLIED TECHNOLOGIES LTD E329973 BOUNDARY HOUSE BUSINESS CENTER BOSTON MANOR RD LONDON, W7 2QE UNITED KINGDOM Class 2 LED Modules, Models MS-P40XXX-XX Series, whecd XXX-XX may be any alphanumeric characters. 1. These LED panel of these products are powered by Class/power source rated at max. 15 VDC, 5 amps. 2. These products are suitable for use in dry and damp locafions. 3. In the end product, power supply spacing to other he*broducing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top ofpnclosure. 4. In the end product the LED face shall be protected' from rain. ACTOWN-ELECTROCOIL INC 5;46102 2414 HIGHVIEW ST. PO BOX 248 SPRING GROVE, IL 60081/ LED Power Supply with Class 2 Odiputs, Cat. Nos. LPS12-04. 1. These power supplies have mpple outputs. The power supply has a maximum of four Class 2 outputs. The power supplyhas been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class Woutputs are suitable for use in dry, damp and wet locations. 3. -Power supply spacing to other heat producing components'shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is Jpt at minimum 2 inches. 4. When not marked fptioor use only, all units shall be provided with liquid tight fittings on the primary and secondarycircuits. ADDICKS ENGINEERING & PRODUCT DEVELOPMENT CO. LTD.E250540 6006 SHULL *T. BELL GARDENS, CA 90201 Class 2 LEDs/tat. Nos. LED Module Pricer. 1. These pdducts are only suitable for connection to a UL Listed or Recognized Class 2, 12 Volt or less DC power source. 2. Thes*;oducts have not been evaluated for use when connected to a power source that does not comply with Class 2 voltaggand energy limited supplies. 3. Thdke Class 2, "LED Module Pricer" Series when connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. AGILIGHT INC.E255447 1702 W AVE N SAN ANGELO, TX 76904 Class 2 LEDs, Cat. No. "Tuffrayz-X" (Where X = denotes LED color: R=Red; W=White, G=Green, B=Blue, O=Orange, A=Amber). 1. LED's may be supplied by a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2,12 VDC maximum output power source. 2. LED's were evaluated for connection to a UL Recognized Component Sign Accessory - UYMR2, Class 2 power supply. 3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limiting requirements. 4. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. Class 2 LEDs Models AGI-BSX-12-XX series, where XX may be WW, SW, NW, TW, DW, AW, RD, BL, AM or GN. 1. These products are only suitable for connection to a Class 2 power source rated 27 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated greater than 27 V DC. 3. These products are each rated max. 9.5 watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 27 Volts DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered.