Laserfiche WebLink
F¥,04 <br />PART 1 - GENERAL <br />1.1 SUMMARY <br />A. WORK INCLUDES <br />1. GreenFasten solar attachment bracket that <br />attaches directly to the roof deck. <br />2. Provide appropriate bracket and fasteners <br />for the roof system. <br />B. RELATED SECTIONS <br />1. Section 07600: Flashing and Sheet Metal <br />2. Section 07500: Roof,ng <br />3. Division 1: Administrative and Procedural <br />Requirements <br />4. Division7: Thermal and Moisture Protection <br />1.2 SYSTEM DESCRIPTION <br />A. COMPONENTS: <br />1. GreenFasten GF1 system consists of alumi- <br />num flashing with integral EPDM bushing <br />and one bonded stainless steel and EPDM <br />washer. <br />2. Fasteners <br />A. To be of metal compatible with aluminum <br />GreenFasten components. <br />B. Fasteners should be selected for compat- <br />ibility with the roof deck. <br />C. Fastener strength should exceed or be <br />equal <br />to that of the allowable load of the system. <br />See test data at www.ecofastensolar.com <br />3. Sealant (if required by roof manufacturer): <br />to be roof manufacturer approved. <br />4. Aluminum compression bracket <br />B. DESIGN REQUIREMENTS: <br />1. Bracket spacing to be recommended by <br />project engineer. <br />2. Install a minimum ofone fastener per <br />assembly. <br />3. It is important to design new structures or <br />assess existing structures to make sure that <br />they can withstand retained loads. <br />1.3 SUBMITTAL <br />A. Submit manufacturer's written specifications. <br />B. Submit standard product cut sheets. <br />C. Submit installation instructions. <br />D. Submit product specific load test data, showing <br />ultimate and allowable load values. <br />1.4 QUALITY ASSURANCE <br />Installer to be experienced in the installation of <br />specified roofing material for no less than 5 years in <br />the area of the project. <br />1.5 DELIVERY / STORAGE / HANDLING <br />Inspect material upon delivery. Notify manufacturer <br />within 24 hours of any missing or defective items. <br />Keep material dry, covered, and offthe ground until <br />installed. <br />PART 2 - PRODUCTS <br />2.1 MANUFACTURER <br />EcoFasten Solar <br />289 Harrel Street, Morrisville, VT 05661 <br />(877) 859-3947 <br />www.ecofastensolar.com <br />2.2 MATERIALS <br />A. Attachment Bracket <br />6000 Series Aluminum <br />1. Comp Slide 4"Bracket <br />B. Fasteners (may be supplied by others) to be <br />compatible with chosen roof application and <br />meet specified pull out values as shown in load <br />test data. <br />Specifications <br />C. Base flashing is.032 gauge aluminum em- <br />bossed <br />to accept EPDM bushing. <br />D. Bushing is EPDM. <br />E. Stainless steel bonded washer is 30418.8 stain- <br />less and EPDM. <br />2.3 FINISH - Mill Finish <br />A. Bracket is mill finish aluminum <br />8. Base flashing (choose one) <br />1. Black- kynar painted <br />PART 3 - EXECUTION <br />3.1 EXAMINATION <br />A. Substrate: Inspect structure on which brackets <br />are to be installed and verify that it will <br />withstand any additional loading that may be <br />incurred. <br />B. Notify General Contractor of any deficiencies <br />before installing EcoFasten Solar brackets. <br />C. Verify that roofing material has been installed <br />correctly prior to installing solar attachment <br />brackets. <br />3.2 INSTALLATION <br />A. Comply with architectural drawings and proj- <br />ect engineer's recommendations for location <br />of system. Comply with Manufacturer's written <br />installation instructions for installation and <br />layout. <br />877-859-3947 Committed to the 5upport of Renewable Energy © Ecofasten Solar All content protected under copyright. All rights reserved. 04/8/14 4.1 <br />9 1\2/3/ <br />1 , <br />i i <br />\ 1 <br />1,1 <br />1 <br />1 1 ./ <br />t <br />11 3 1 <br />4 <br />j , <br />-Eco-Faitdn--Solar -76= <br />-- <br />2