Laserfiche WebLink
·.STOREINE. Cox <br />C c C.0.. <br />Joint PreparationCEMLINK- M-1 Structural <br />Joint surfaces should be clean, dry and free from all Typical Physical Properties <br />contamination including: dirt, oils, grease, tar, wax, <br />nist and any other substance that may inhibit the <br />Gun Grade Zero Slump COMPONENT SPECSAdhesive/Sealant sealant's performance.POLYMER INNOVATION <br />Brookfield RVF TF Description Date Rev <br />1,200,000 cpJoint Design Viscosity +/-400,000 cp Spindle, 4 RPM,ORIGINAL 4/25/14 ATechnical Data Guide Polyether Technology CSI Section No. 07 92 13 Install all joint applications per ASTM and SWRI 73°F (23°C) <br />recommendations and guidelines. Joints shall be 11.8 +A 0.2 lbs <br />CHEM LINK Brands Last Revision: 04/14/14 designed with a depth to width ratio of 1:2 (joint depth Density ASTM D1475 <br />Telephone: 800-826-1681 Document No. L1270 one-half the width). Control the depth of the sealant <br />per gallon <br />Fax: 269-679-4448 by using a polyethylene backer rod that is 25% larger Tack Free 20 min +A 10 min 45 +/- 5 % R.H.353 E Lyon Street than the joint opening at standard temperature. To Time <br />Schoolcraft, MI 49087 prevent three-point adhesion use a backer rod or <br />bond breaker tape to ensure proper joint movementwww.chemlink.com Elongation atand a long lasting weatherproof seal. Where the joint 290%ASTM D412 <br />Break <br />configuration will not permit a backer rod, CHEMProduct Description <br />M-1® is a moisture curing, polyether adhesive Hardness <br />ASTM C661 <br />LINK recommends that an alternative bond breaker <br />45sealant designed for applications in damp, dry, or be used.Shore A <br />cold climates.Md® is solvent free and contains CONTRACTOR: <br />no isocyanates. M-1® will not shrink upon curing, Tensile Stearns Solarwill not discolor when exposed to UV light, and Joint Width Joint Depth 330 psi ASTM D412 <br />Strength 16381 Nosoni Rd.can not "out-gas", or bubble on damp surfaces as Inches (mm)Inches (mm) <br />urethane sealants often do. Md® is capable of joint Apple Valley, CA 92307Shearmovement in excess of 25% in both compression 1/4 - 1/2 (6-13)1/4 (6)380 psi ASTM D1002 760-514-1537Strength <br />LlC# 988327and extension. M-1® can be used effectively in many <br />difficult construction site conditions such as wet or dry 1/2 - 3/4 (13-19)1/4 - 3/8 (6-10 <br />Low temp.Pass -10°F (-23°C)climates and at temperatures as low as 32°F (0°C).ASTM D816 <br />nex 1/4 inch mandrel <br />J <br />Applicable Performance Standards <br />• ASTM C920, Type S, Grade NS, Class 25 <br />Uses NT, Ti, M, G, A&O <br />· Federal Specification TLS-00230-C Type It Class B <br />· Corps of Engineers CRD-C-541, Type Il, Class B <br />· Canadian Standards Board CAN 19, 13-M82 <br />Advantages <br />· Solvent free, 100% solids will not shrink <br />· Non-slump, applies vertically and overhead <br />· 20 minute skin over <br />· No outgassing on damp surfaces <br />· Good color stability, will not suntan <br />· Paintable within 24 hours (See limitations) <br />· Gun grade, no special tools or mixing required <br />· Application at temperatures as low as 32°F (0°C) <br />3/4 - 1 (19-25)3/8 - 1/2 (10-13) <br />CHEM LINK recommends an appropriate substrate <br />primer to be used on high moving joints or dissimilar <br />substrates which require increased adhesion <br />properties. <br />Compatible Substrates* <br />Shrinkage No visible shrinkage after 14 days <br />Service <br />-40°F to 200°F (-40°C to 93°C)Temperature <br />Basic Uses <br />HOME OWNER: <br />Paul Ziesmer <br />2202 Freeman St. <br />Santa Ana, CA 92706 <br />714-560-0600 <br />PROJECTADDRESS: <br />2202 Freeman St. <br />Regulatory Compliance <br />· Conforms to OTC Rule for Sealants and Caulks <br />· Meets requirements of California Regs: <br />CARB, BAAQMD and SCAQMD <br />· Conforms to California Proposition 65 <br />· Conforms to USDA Requirements for Non-food Contact <br />Green Standards: <br />· LEED 2.2 for New Construction and Major Renovations: <br />Low Emitting Materials (Section 4.1) 1 Point <br />· NAHB Model Green Home Building Guidelines: <br />5 Global Impact Points <br />· VOC Content less than 20 grams / literASTM D2369 <br />EPA Method 24 (tested at 240°F / 115°C) <br />Colors <br />White Gray tifE!20%22BlackEID <br />* Color matching is available in batbh quantity only <br />Packaging <br />• 5 oz Squeeze Tube (150 mi) <br />36 tubes/carton, 40 cartons/pallet <br />• 10.1 oz (300 mi) <br />24 cartridges/carton, 45 cartons/pallet <br />• 20 oz (600 mi) <br />12 sausages/carton, 40 cartons/pallet <br />· 28 oz (825 mi) <br />12 cartridges/carton, 40 cartons/pallet <br />White only - Other colors available by <br />special order <br />• 2 and 5 gallon pails or 50 gallon drums <br />available by special order <br />EPDM and SBS Mod Bit <br />Aluminum and Galvanized Metal <br />Stainless Steel <br />Engineered Plastics, PVC <br />Glass <br />Fiberglass FRP <br />Wood <br />Block and Brick <br />EPS Foam <br />Concrete and Stone <br />*Test and evaluate to ensure adequate adhesion.Page 2 <br />Expansion joints <br />Pre-cast concrete <br />Block and Masonry <br />Window and door frames <br />Siding <br />Parapets <br />Cove Joints <br />Transportation <br />Weather Sealing <br />Santa Ana, CA 92706 <br />PV-7.2 <br />©2012 pvlabels.com