10179217_2800 N. MAIN 248 - Plan (2)

Home Browse Search

November 14, 2012 SIGN COMPONENTS MANUAL (SAM)122 5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product. 6. When not marked for Dry and Damp Locations Only the power supply primary bracket shall be provided with min. 3.5 threads and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3.5 threads, the liquid tight shall be provided with watertight fitting Listed (QCRV) 1/2 inch, liquid tight conduit fittings. 7. The suitability of grounding connection shall be determined in the end-use product. Class 2 power supply, Model 701680. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief on input lead construction and Impact Tests have not been investigated. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of each unit is V-2, and the necessity of additional fire barriers shall be determined in end product. 7. Multiple power supplies shall be spaced at least 25mm (1 in.) end to end or 102mm (4 in.) in other directions. If lesser spacings are used, then the Temperature Test shall be conducted in the end use product. For reference the maximum enclosure (case) temperature on the power supply was 90°C when tested at 58.4° ambient. Class 2 power supply, Model 701680-MW. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 2. The load powered by the Class 2 output of the power supplies rated at max 30 VDC or less are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of endosure. 4. These products are provided with the following electrical ratings: Input Output Model I Vac A Hz Vdc A 701680-MW | 100-240 0.55 50/60 12 1.67 5. These products shall be enclosed in the end product. 6. These power supplies are suitable for use in dry and damp locations. Class 2 power supply, Model 701681. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1, 300 V, 105°C. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated on input lead construction. The suitability of the endosure as ultimate enclosure shall be determined in the end-use application. 6. The polymeric enclosure of each unit has not been evaluated as ultimate endosure. The flame class of the polymeric enclosure is V-0 and the necessity of additional fire barriers shall be determined in end product. 7. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Class 2 power supplies, Model 701495. 1. These power supplies have been evaluated to Class 2 output requirements for dc circuits with a maximum of four Class 2 outputs. 2. These power supplies are only suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat produdng components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Class 2 power LED Lighting Strip, 701912-QQXXYYZZZ series, where QQ represents length, XX represents the LED color temperature, YY represents configuration and ZZZ represents the LED drive current. 1. These products are only suitable for connection to a Class 2 power source, rated 24VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 24VDC. 3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated class 2. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered. Class 2 "Dimming Control Knob" potentiometer, Model 701843. 1. These products are only suitable for connection to the output of a UL Listed or Recognized Class 2 power supply rated max 12 VDC. 2. These products are suitable for use in dry and damp locations. 3. These products are suitable for factory wiring only. 4. These products are 1 Kohm potentiometers intended for connection to max 12 VDC Class 2 power supply that drops the voltage to a 0-10 V signal to feed into the PWM dimmer. SPARTECH PLASTICS E202184 3454 N DETROIT ST WARSAW, IN 46580 Rigid sign enclosure systems, designated SunGard, Sungard Plus, PC-2000, DuraGard and PC-2000 Plus.