|
Exhibit A: Master Compliance Record (MCR)
<br />PLEASE RECORD MARKING INFORMATION IDENTIFIED ON SIGN:Instructions: the manufacturer must complete this form for each sign or family of sign
<br />manufactured. As an alternate, the manufactured may use their own document or form provided the
<br />following content is available for review by the UL field representative curing UL factory
<br />Inspection visits. Electronics records are acceptable.
<br />Electrical Ratings
<br />120 Volts 1.5 Amps
<br />Frequency (HZ)
<br />Date Code Listing mark serial #
<br />07/22/13 N/A
<br />The products identified below were reviewed for compliance with applicable requirement
<br />current version of UL 48 Standard, UL Follow-up Inspedion Instructions, SAM, applicable,
<br />bulletins, and times note below:
<br />UL mark applied Applied
<br />I Yes , O Ne " 541' O 6..'el,ORivul
<br />Grounding Bonding StatementAccordance with
<br />Article 600 NEC inctuded I Yes / O\JO
<br />UL File #:Volume #:
<br />Product type Identlfication:
<br />(list model no,, pan no. customer name, etc )
<br />Unique Identification
<br />(list date code, senal #, lot #, or other unique identifier)
<br />Sign Construction type:
<br />O Outdoor O Cabinet Sign
<br />1 Indoor 0 Section (no. of sedions:_J
<br />Date of Manufacture
<br />BAG IN STYLE
<br />Illumination Sourse:
<br />Ofluorescent ONeon ILED
<br />HID Incandescent
<br />1. Please record information for critical components and material used in the sign construction
<br />2. As an alternate, the manufacturer may choose to attach a parts list (hard copy or electrical )in
<br />lieu of completing the following list. If parts list is attached, please check box here.
<br />3. Critical components include the fallowing components:
<br />ballasts, transtormers, power supplies
<br />heat producing components, plastics, fiexible signs face materials, gaskets, boots. sleeving
<br />lanip holders and electrodes, switches, AWM and wiring materials, etc.
<br />all components shall be 1. listed, 2. recognized in sign components manual: 3. classified for use with sign
<br />4. FUS procedure described,
<br />Construction Review (see notes):
<br />The sign(s) was evaluated using this
<br />criteria and found to comply with UL 48
<br />requirements:
<br />Performance Review (see notes):
<br />The sign (s) was evaluation using the following criteria
<br />and found to comply with requirements:
<br />LED CHANNEL LETTERS
<br />SIGN COMPONENTS / SPECS
<br />>< LED LIGHT COMPANY NAME SS LIGHT SERIES WHITE
<br />1. Frame and Enclosure
<br />2. Ventilating Openings
<br />3. Sign face / Panels
<br />4. Resistance to Moisture / Drain Holes
<br />5. Ground and Bonding
<br />6. Electrical & Thermal spacings
<br />7. Wire Routing & support
<br />8. General workmanship
<br />a. e.g. no metal shavings or sharp
<br />edges, etc.
<br />9. Correct Hardware
<br />a. e.g. wire nuts, fasteners,
<br />1. mechanical tests
<br />2. Exclusion of water test
<br />3. Strain relief test
<br />4. Grounding Continuity
<br />5. List other tests performed.
<br />LED TRANSFORMER
<br />X MODEL
<br />DC VOLTAGE
<br />RATED CURRENT
<br />RATED RANGE
<br />RATED POWER
<br />CLASS 2 POWER
<br />LED CABLES
<br />UL#: E346996
<br />2
<br />FAHUA E
<br />MODEL: HMA·100NU-RX 8
<br />12V
<br />8A
<br />I.SA
<br />100 W /
<br />12V/2 CIRCUIT
<br />.E
<br />SLOAN CABLE SLO- CABLE- M
<br />fittings, gaskets, etc.
<br />10. Electrical / Supply connections
<br />a. Electrical Schematics
<br />11. Installation instructions (provided with sign)
<br />12. Correct Components
<br />(complete Critical components list next page)
<br />PLASTICS 3/16'-r.
<br /> METALS .090 THICK Z
<br />LEXAN NAME GE PLASTICS,150 THICKNESS
<br />LEXAN MSG4101-4
<br />TRIMCAP 3/4'JEWEL TRIP CAP m2
<br />For construction Review and Performance Review:
<br />All of the above criteria was met satisfactorily in compliance with UL 48 : I YES
<br />if NO or N/A, describes specifies:
<br />C]NO [ZIN/A
<br />SCREWS SELF TAP /MACHINE
<br />For any box checked 'No' above, what
<br />containment action was taken ?
<br />O Sign reworked and repaired
<br />O Sign shipped but is not labeled w/ UL mark
<br />O Sign scrapped other disposition :
<br />If Sign was repaired, describe reqork actions below
<br />Was sign re-inspected or retested and found to comply
<br />with requiremetns?
<br />U Yes INo IN/A
<br />SWITCH
<br />WIRE NUTS
<br />POLYCARBONATE
<br />WHITE UV
<br />TUF GLASS
<br />TOGGLE
<br />UL LIST EC) ORANGE _ RED_ BLUE _
<br />SPARTECH PLASTICS
<br />.150 THICKNESS
<br />MSG45-4
<br />SPARTECH PLASTICS TUF GLASS
<br />-177 THICKNESS
<br />MTG17-42
<br />Notel · If results do not comply products must be re-worked and bought and back into compliance or not with UL Mad<.
<br />If re-worked, products must be re-ininspected or retested to verify compliance.
<br />Note 2: Record O4etails ot results if no-contormances are identified, Including disposition and rework details. Recorded
<br />Corrective actions taken to bring the product into conforniance.
<br />By Con,wo#ng 0)0 intomm#an bdow, ; contimi chal thi p,odusts #*zodabovo woriman,flac:un,d, in,poctod, fostod Ind doto,minid to be b oompling• with UL ioquwornonti,
<br />Completed by Manufacturer SIGNCOMM CHRIS LEE 07-22-13
<br />Technical representative Company Name Print Name -Date. ,
|