Laserfiche WebLink
REV <br />SHEET NAME <br />SHEET SIZE <br />SHEET NUMBER <br />JE <br />F <br />F <br />R <br />E <br />Y <br /> <br />C <br />H <br />E <br />N <br />G <br />ANSI B <br />11" X 17" <br />DATEDESCRIPTION <br />REVISIONS <br />Signature with Seal <br />PROJECT NAME & ADDRESS <br />PV-8 <br />CONTRACTOR NAME <br />CONTRACTOR INFORMATION <br />PH <br />O <br />N <br />E <br />: <br />- <br /> <br />+1 <br />4 <br />1 <br />5 <br />3 <br />6 <br />1 <br />0 <br />8 <br />4 <br />5 <br />27 <br />0 <br />9 <br /> <br />D <br />A <br />Y <br />N <br />A <br /> <br />S <br />T <br />, <br />SA <br />N <br />T <br />A <br /> <br />A <br />N <br />A <br />, <br /> <br />C <br />A <br /> <br />9 <br />2 <br />7 <br />0 <br />5 <br />AH <br />J <br />: <br />- <br /> <br />SA <br />N <br />T <br />A <br /> <br />A <br />N <br />A <br /> <br />C <br />I <br />T <br />Y <br />CO <br />U <br />N <br />T <br />Y <br />: <br />- <br /> <br />(O <br />R <br />A <br />N <br />G <br />E <br /> <br />C <br />O <br />U <br />N <br />T <br />Y <br />) <br />SOLAR OPTIMUM <br />501 W. GLENOAKS BLVD #555 <br />GLENDALE, CA, 91202 <br />(818) 804-3122 <br />CALIFORNIA C-10 <br />LIC# 972228 <br />ARPIAR TARVERDI <br />WIRING <br />CALCULATIONS <br />ELECTRICAL NOTES <br />1.) ALL EQUIPMENT TO BE LISTED BY UL OR OTHER NRTL, AND LABELED FOR ITS APPLICATION. <br />2.) ALL CONDUCTORS SHALL BE COPPER, RATED FOR 600 V AND 90 DEGREE C WET ENVIRONMENT. <br />3.) WIRING, CONDUIT, AND RACEWAYS MOUNTED ON ROOFTOPS SHALL BE ROUTED DIRECTLY TO, AND <br />LOCATED AS CLOSE AS POSSIBLE TO THE NEAREST RIDGE, HIP, OR VALLEY. <br />4.) WORKING CLEARANCES AROUND ALL NEW AND EXISTING ELECTRICAL EQUIPMENT SHALL COMPLY <br />WITH NEC 110.26. <br />5.) DRAWINGS INDICATE THE GENERAL ARRANGEMENT OF SYSTEMS. CONTRACTOR SHALL FURNISH ALL <br />NECESSARY OUTLETS, SUPPORTS, FITTINGS AND ACCESSORIES TO FULFILL APPLICABLE CODES AND <br />STANDARDS. <br />6.) WHERE SIZES OF JUNCTION BOXES, RACEWAYS, AND CONDUITS ARE NOT SPECIFIED, THE <br />CONTRACTOR SHALL SIZE THEM ACCORDINGLY. <br />7.) ALL WIRE TERMINATIONS SHALL BE APPROPRIATELY LABELED AND READILY VISIBLE. <br />8.) MODULE GROUNDING CLIPS TO BE INSTALLED BETWEEN MODULE FRAME AND MODULE SUPPORT <br />RAIL, PER THE GROUNDING CLIP MANUFACTURER'S INSTRUCTION. <br />9.) MODULE SUPPORT RAIL TO BE BONDED TO CONTINUOUS COPPER G.E.C. VIA WEEB LUG OR ILSCO <br />GBL-4DBT LAY-IN LUG. <br />10.) THE POLARITY OF THE GROUNDED CONDUCTORS IS NEGATIVE <br />NUMBER OF CURRENT <br />CARRYING CONDUCTORS IN <br />EMT <br />4-6 <br />7-9 <br />10-20 <br />PERCENT OF <br />VALUES <br />.80 <br />.70 <br />.50 <br />AMBIENT TEMPERATURE SPECS <br />AMBIENT TEMP (HIGH TEMP 2%) <br />RECORD LOW TEMP 1° <br />33° <br />CONDUIT HEIGHT 7/8" <br />ROOF TOP TEMP 75° <br />CONDUCTOR TEMPERATURE RATE 75° <br />OPTIMIZER SPECIFICATIONS <br />POWER OPTIMIZER TESLA PV RAPID SHUTDOWN <br />NOMNAL INPUT DC CURRENT 13A <br />MAX INPUT SHORT CIRCUIT <br />CURRENT 15A <br />DC INPUT POWER 1000VDC <br />DC CONDUCTOR AMPACITY CALCULATIONS: <br />ARRAY TO JUNCTION BOX: <br />DC CONDUCTOR AMPACITY CALCULATIONS: <br />FROM JUNCTION BOX TO INVERTER: <br />AC CONDUCTOR AMPACITY CALCULATIONS: <br />INVERTER TO EX MSP. <br />EXPECTED WIRE TEMP (In Celsius)33° <br />TEMP. CORRECTION PER TABLE (310.16)0.94 <br />NO. OF CURRENT CARRYING CONDUCTORS 6 <br />CONDUIT FILL CORRECTION PER NEC 310.15(B)(2)(a) <br />CIRCUIT CONDUCTOR SIZE 10 AWG <br />CIRCUIT CONDUCTOR AMPACITY 35A <br />REQUIRED CIRCUIT CONDUCTOR AMPACITY PER NEC 690.8(A&B) <br />18.75A <br />1.25 X MAX. DC OUTPUT CURRENT (RSD) <br />DERATED AMPACITY OF CIRCUIT CONDUCTOR PER NEC TABLE 310.16 <br />32.90ATEMP. CORRECTION PER TABLE (310.16) X <br />CONDUIT FILL CORRECTION PER NEC 310.15(B)(2)(a) X CIRCUIT <br />CONDUCTOR AMPACITY <br />Result should be greater than (18.75A) otherwise less the entry for circuit conductor size and <br />ampacity <br />EXPECTED WIRE TEMP (In Celsius)33° <br />TEMP. CORRECTION PER TABLE (310.16)0.94 <br />NO. OF CURRENT CARRYING CONDUCTORS 6 <br />CONDUIT FILL CORRECTION PER NEC 310.15(B)(2)(a)0.80 <br />CIRCUIT CONDUCTOR SIZE 10AWG <br />CIRCUIT CONDUCTOR AMPACITY 35A <br />REQUIRED CIRCUIT CONDUCTOR AMPACITY PER NEC 690.8(A&B) <br />18.75A <br />1.25 X MAX. DC OUTPUT CURRENT (RSD) <br />DERATED AMPACITY OF CIRCUIT CONDUCTOR PER NEC TABLE 310.16 <br />26.32ATEMP. CORRECTION PER TABLE (310.16) X <br />CONDUIT FILL CORRECTION PER NEC 310.15(B)(2)(a) X CIRCUIT <br />CONDUCTOR AMPACITY <br />Result should be greater than (18.75A) otherwise less the entry for circuit conductor size and <br />ampacity <br />No. OF INVERTER 1 <br />EXPECTED WIRE TEMP (In Celsius)33° <br />TEMP. CORRECTION PER TABLE (310.16)0.94 <br />NO. OF CURRENT CARRYING CONDUCTORS 3 <br />CONDUIT FILL CORRECTION PER NEC 310.15(B)(2)(a)1 <br />CIRCUIT CONDUCTOR SIZE 6AWG <br />CIRCUIT CONDUCTOR AMPACITY 65A <br />REQUIRED CIRCUIT CONDUCTOR AMPACITY PER NEC 690.8(B) <br />60.00A <br />1.25 X MAX INVERTER OUTPUT CURRENT <br />DERATED AMPACITY OF CIRCUIT CONDUCTOR PER NEC TABLE 310.16 <br />61.10ATEMP. CORRECTION PER TABLE (310.16) X <br />CONDUIT FILL CORRECTION PER NEC 310.15(B)(2)(a) X CIRCUIT <br />CONDUCTOR AMPACITY <br />Result should be greater than (60.00A) otherwise less the entry for circuit conductor size and <br />ampacity <br />SOLAR MODULE SPECIFICATIONS <br />MANUFACTURER / MODEL # <br />VMP <br />IMP <br />VOC <br />ISC <br />MISSION SOLAR MSX10-435HN0B <br />435W MODULES <br />MODULE DIMENSION <br />33.31V <br />13.07A <br />39.56V <br />13.79A <br />67.8"L x 44.73"W x 1.18"D (In Inch) <br />MODULE TEMPERATURE COEFFICIENT OF Voc -0.24%/°C