10179561_2022 E. 17TH - Plan (2)

Home Browse Search

87 SIGN COMPONENTS MANUAL (SAM)June 19, 2013 SANTA CLARA, CA 95054 Class 2 LED Panel, GLB Series. 1. These products are only suitable for connection tothe output of a Class 2 Power Supply rated 24VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater thanthe secondary current rating of each Class 2 power supply. 4. These products are suitable f6r use in dry and damp locations without additional enclosures. LVC CONNECTORS INC E339231 6068 METROPOLITAIN E MONTREAL, QC Hl S 1A9 CANADA PVC Tube, Models LVC-3 and TK-24-XXX. 1. These products are only suitable for protecting leted Class 2 wiring that ate supplied by power supplies that are marked as having a Class 2 output or LPS. 2. For outside wall use only. 3. Not suitable for inside walls. 4. These products may be secured in place in the end product by any means available Class 2 Low Voltage Connectors. Model LVC2, LVC4. SNAP-KONEK Ill, and STICK-KONEK. 1. These devices are not suitable for interrupting the flow of current by connecting or disconnecting. 2. These products are only suitable for connection to a Class 2 power source, Class 2 supply rated max. 15 Volts AC or max. 30 Volts DC or less. 3. These products have not been;evaluated for use when connected to a power source that does not complywith Class 2 voltage and energy limits. 4. These products are suitable for use in dry, damp and wet locatiohs. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. Modules can be installed to interconnect leads in the field or pre-installed. 7. These products may be secured in place in the end product by mechanical securement or double sided adhesive tape. 8. For Model LVC2 and LVC4, suitable for connecting stranded wires which are 18, 20 or 22 AWG with compatible wire guide inserts. 9. For.Model SNAP-KONEK 111, suitable for connecting single conductor per channel either AWM wires 18-24 AWG, or Power- Limited Circuit Cables type CL3P, CL3R, CL3, CL3X, CL2P, CL2R, CLZ, CL2X and PLTC. 10. The Model STICK-KONEK base and button are used to join LED strips, LED bars, or LED leads wires. MAGTECH INDUSTRIES CORP E314969 5625-A S ARVILLE ST LAS VEGAS, NV 89118 Class 2.LED Module, Cat. No. LP12060P-08, LP12060.P-09, LP1206.OP-10, LP12060P-11,LP12060P-12, LP24060P-22, EP24060P-23,LP24060P-24. 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shaU be rhinimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit filtings on both primar'y and secondary circuits. MATRIX FRAME E351057 FLEVOWEG 27 2318 BZ LEIDEN, THE NETHERLANDS Class 2 LED Module, "Lightbox CREE XP LEDstrip". 1. These products are suitable for use in Dry and Damp Locations Only and may only be supplied with a Class· 2 power source with Cufrent [imit rated max. 2.5 Amps or less. 2. These products are only suitable for connection to a Class 2 or LPS power source, rated 24 Volt DC or less. 3. These products shall be mounted in equipment, which provide a suitable overall enclosure. 4. A maximum of 4 Led strips are allowed to be mounted in a row, as detailed in the moOnting instructions. 5. These products may only be installed in a metal based enclosure (frame) that is able to transfer the heat that comes from the LEDs over the metal-core Printing Wiring Board into the ambient. MATRIX FRAME E358648 FLEVOWEG 27 2318 BZ LEIDEN, THE NETHERLANDS Class 2 LED driver box, Model A120606. 1. The power supply has been evaluated to Class 2 output requirements for dc circuits with a maximum of one Class 2 output. 2. The Class 2 output of the power supply is suitable for use in dry and damp locations only. 3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. These products shall be enclosed in the end product. 5. These products are suitable for factory wiring only.