10179804_1229 E. 17TH - Plan (2)

Metadata

Thumbnails

Annotations

41 SIGN COMPONENTS MANUAL (SAM)June 19, 2013 1. The Neon "Animotion" Controller shall be used within the ratings indicated above. Its input shall be powered by the Class 2 output of Model 800-0128 with the controller's output powering the input of Series "NuAUX" auxiliary transformers or the controller's input shall be powered by a Listed Class 11 high-frequency power supply. 2. The controller has been evaluated at maximum marked ratings with Neon Power Supply Cat. No. 1212 and Cat. No. 800-0065 auxiliary transformer. 3. The number of outputs on the controller may vary between one and eight. 4. No more than four outputs, with a maximum of two outputs per input, may be operated continuously. 5. All eight outputs shall not be on concurrently. 6. The controllers are intended for Indoor Use Electric Signs or shall be mounted in suitable enclosure when used with Outdoor Use Electric Signs. LED Modules, Sequencer Series Modules designated XXX-XXXX, XXX-YYYY or XXX-YYYYY (XXX-XXXX, XXX-YYYY or XXX- YYYYY may be any combination of alpha characters). 1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less. 2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be required. 3. Each module is rated and suitable for a maximum of 90 watts. 4. Sequencer modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less. 5. Sequencer modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less. 6. These modules should be secured by suitable means when installed in the end-use application. 7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require additional evaluation. 8. When the Sequencer modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these application are only suitable for use in the United States. LED Modules, Regulator Series Modules designated XXX-XXXX, XXX-YYYY or XXX-YYYYY (XXX-XXXX, XXX-YYYY or XXX- YYYYY may be any combination of alpha characters) 1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less. 2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be required. 3. Each module is rated and suitable for a maximum of 90 watts. 4. Regulator modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less. 5. Regulator modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less. 6. These modules should be secured by suitable means when installed in the end-use application. 7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require additional evaluation. 8. When the Regulator modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these application are only suitable for use in the United States. LCD Module, Model LCD v6.x with Power Supply. 1. These LCD modules are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These LCD modules have not been evaluated for use and connection to a power supply source with- parameters that exceed Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be required. 3. Each LCD module is rated and suitable for a Class 2 maximum 12 Vdc output of 43 watts. 4. The Exclusion of Water Test may be waived for this LCD module subassembly only when installed in outdoor location signs with Listed conduit and (QCRV) liquid light conduit fittings on primary circuits. 5. These modules should be secured by suitable means when installed in the end-use application. 6. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require additional evaluation. LED Modules, Cat. No. LCD v6.x with Power Supply. 1. These modules are only suitable for connection to a Class 2 power source rated 60 Volt DC or less. 2. These modules have not been evaluated for use and connection to a power supply source with parameters that exceed Class 2 circuit limitations. If and when connected to circuits with parameters exceeding these limits, additional evaluation will be required. 3. Each module is rated and suitable for a maximum of 90 watts. 4. Regulator modules are suitable for use only in dry locations with supply sources rated at 60 Volts DC or less. 5. Regulator modules are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volts DC or less. 6. These modules should be secured by suitable means when installed in the end-use application. 7. These modules are suitable for use in signs only. The use of these modules in any other end-use application will require additional evaluation. 8. When the Regulator modules are connected to a Class 2 source of supply with a potential of 42.4 V DC or more, these application are only suitable for use in the United States. EVERBRITE LLC E360604 SUITE 208 BLDG B 380 SEMORAN COMMERCE PL LED Modules, Models CST-20-B, CST-20-G, CST-20-R, CST-20-RGB, CST-2D-W, CST-30-A, CST-3D-B, CST-30-G, CST-3D- R, CST-3D-RGB, CST-30-W, CST-30-VWV, CST-40-B, CST-40-G, CST-40-R, CST-40-RGB, CST-4D-W 1.These products are only suitable for connection to a Class 2 power source rated 12 Volt DC or less. 2. These products are intended for use only when connected to a power source that complies with Class 2 voltage and energy limited circuit and is rated greater than 12V DC.