10179929_5210 W. 1ST A - Plan (2)

Home Browse Search

55 SIGN COMPONENTS MANUAL (SAM)October 1, 2013 6. These LED drivers are intended to be operated on a maximum 20 A branch circuit. 7. The need of the grounding means shall be determined in the end product. 8. These LED drivers shall be enclosed within a suitable end product enclosure. 9. For model LD-60-UV-24\ADIW, the conduit knockout test was not conducted. The suitability is to be determined in end product. 10. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 11. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less than 4 inches (102mm) apart when arranged otherwise. LED Driver with Class 2 Output, Model GEPS12-180U. 1. The output (Red/Black) of each unit complies with Class 2 criteria of UL 1310. 2. The device is provided with 18 AWG input and output leads. The suitability of input and output connections shall be determined in end-use application. 3. The suitability of grounding means shall be determined by end product. 4. The device is not intended for field wiring used. 5. The device is intended to be connected to a maximum 20 A branch circuit. 6. The devices are of the constant current type that requires the proper number of LED modules and controllers that does not exceed the maximum output voltage/current. 7. The measured maximum external enclosure temperature Ec) is 77.2 degree C when the room ambient temperature are 60 degree C. The suitability shall be determined in end application. 8. The devices employ input surge suppression protection, Cat. No. S14K385E2K1 under UL File E321126, which is intended end- use SPD type 2. The suppressed voltage rating is 385 Vac. The suitability of use of this component shall be determined in the end-product application. 9. No mechanical test has been conducted for the models and the metal chassis is considered as dead metal. The devices shall be mounted in the intended manner in an enclosure, having adequate strength and thickness with acceptable spacing being provided. 10. The device has been evaluated for dry and damp locations use only. 11. In the end product, LED driver spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 12. In the end product, LED Drivers shall be located not less than 1 inch (25.4mm) apart when arranged end-to-end, and not less than 4 inches (102mm) apart when arranged otherwise. LED Driver Extended Enclosure, Model No. GEPSJB60. 1. The J-Box extended enclosure has been evaluated only for use and connection to LED Class 2 Drivers Models GEPS12-60, GEPS12D-60U, GEPS24-80, GEPS24D-80U, GEPS12-60U-NA, GEPS12-60U-GL, GEPS24-100U-NA, and GEPS24-100U- GL.2. These products complete the electrical enclosure when installed over the primary wiring of the LED driver. 3. The suitability of the mounting shall be determined in end use application. 4. The enclosure has been evaluated only for use in Dry and damp locations only 5. Supply connection shall be determined in the end used application. 6. Ground Screw size is No. 6 thread forming screw with cupped washer is provided for grounding. The maximum size ground wire that can be used is 14AWG. The maximum size branch circuit that the units can be connected to is 15A unless a 16- 14AWG.six inch pigtail lead supplied by sign company is connected to ground terminal and then spliced to 12AWG ground wire of a 20 A branch circuit. 7. Cover Screw shall not be of a thread forming or self-tapping type. 8. To keep the enclosure from rotating, the Enclosure shall be secured by at least one mechanical fastener. 9. The J-box has been evaluated for an ambient of 40°C. 10. The J-box label shall be marked for a 75°C supply wire connection. LED Driver with Class 2 Output, Cat Nos. GEPS 12-60U-NA, GEPS 12-60U-GL, GEPS24-100U-NA and GEPS24-100U-GL. 1. These power supplies are provided with Class 2 outputs 2. These products with Class 2 outputs are suitable for use in dry and damp locations. 3. Model Nos. GEPS12-60U-NA, GEPS12-60U-GL have been tested in an oven at max. 40°C ambient and Model Nos. GEPS24- 100U-NA, GEPS24-100U-GL in an over at max. 55 °C. Maximum case temperature at (Tc) for all models should not exceed 85°C. 4. The suitability of grounding connection shall be determined in the end-use product. 5. These products shall be enclosed in the end product. 6. These products are provided with the following electrical ratings: Model Input, 50/60 Hz Rated Output V A V DC A DC W GEPS12-60U-NA,120-277 Max. 0.65 12 5.0 60 GEPS12-60U-GL, GEPS12-60U-NA,120-277 Max. 1.10 24 4.0 96GEPS12-60U-GL 7. These products are suitable for factory wiring only. 8. In the end product, power supply spacing to other heat producing components shall be at least 25.4 mm (1 in.) from end to end, and 101.6 mm (4 in.) from side to side. 9. The suitability of input/output leads and the wring shall be determined in end product use. 10. These LED drivers are intended to be operated on a maximum 20 A branch circuit. 11. These products shall be enclosed in the end product. LED Driver with Class 2 Output, Model GEPS24-180U-GL. 1. The device shall be used within Recognized ratings as specified above. 2. Each output of the unit complies with Class 2 criteria of UL 1310. Multiple output units may exceed Class 2 when the output terminations are interconnected. Do not interconnect output terminations. 3. The device is provided with 18 AWG input and output leads. The strain relief test was not conducted on this device. The suitability of input and output connections shall be determined in end-use application.