10179965_117 S. HARBOR - Plan (2)

Home Browse Search

October 1, 2013 SIGN COMPONENTS MANUAL (SAM)24 3. This material is suitable for direct contact with and mounting to heat producing components such as transformers, power supplies and iballasts in the end product. 4. Marking required on end product<stating, "Replace only with (manufacturer's name of componat), type (type designation of sign face) sign face material". 5. Suitable for use in terminating conduit. 6. Watef exclusion must be determined in the end product. 7. Self-threading screws shall not be used to mount components to these materials. 8, The mounting means of components shall be determined in the end-product. BEYOND LED INC E341708 63 CASSANDRA CRES RICHMOND HILL, ON L4B 4A1 CANADA Enclosure for LED power supply, Model BY-PSE-X. 1. This product has been evaluated for Dry and Damp Locations only. The suitability for wet locations will need to be determined by the end product application. BITROGROUP INC 201 CHARLES ST E341583 HACKENSACK, NJ 07601 LED Module, Models OMX-L4, OMX-L3, OMX-M3, OMX-M2. OMX-S2, OMX-N 1. 1.These products have been evaluated for connection to a Class 2 power source only, rated 12 Vdc, 60 W max. 2. These products are suitable for use in dry. damp or wet locations. 3. The LED module is provided with leads for interconnection. The suitability of the leads shall be determined in the end product. LED Module, Class 2 powered LED modules, BT-XXX series designated as "Linear LED Bars"; "PCB Modules", "Sign Washer", "Channel Letter Modules", "LED Bars- or "Flexible Strips", where XXX may be any alphanumeric characters. 1. These products are only suitable for use in dry, damp and wet locations and supplied with a Class 2 power source rated 24 Volt DC or less. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. BITRO GROUP INC 201 CHARLES ST E351123 HACKENSACK, NJ 07601 Class 2 LED Power Supply, Model ASU-60-12U, ASU-100-24U. 1. The power supply shall be installed in compliance with the applicable requirements of the end-product standard for, mounting, spacing. casualty and segregation. 2. Themaximum available output parameters were within the maximum allowable limits for Class 2, inherently limited as specified in the UL 1310, Standard for Class 2 Power Units and also in accordance wiih the Canadian Safety Standard CSA C22.2 No 223. 3. The power supply was submitted and tested for a maximum manufacturer's recommended Tc location, should not exceed 69°C, in ambient of 40°C. I f adjacent LED power supplies are spaced closer than 1 in. end to end or 4 in. side to side a temperature test shall be conducted in the end use product. 4. Power Supply is intended for use in indoor Dry and Damp location only. 5. In the end product, power supply spacing to other heat producing components shall be'minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. Adjacent power supplies shall be spaced at least 1 in. end to end and 4 in. in any other direction. 6. The input and output leads were not subjected to the strain relief test. 7. The primary (Black-White) and the output (Red-Black) connection wires ef the power supply are R/C (AVLVWAVLVB), 18 AWG, 90°C. The suitability of the leads shall be determined in the end-use application. BLUEVIEW ELEC-OPTIC TECH CO LTD E318168 1000 SECTION 2, 2ND KONGGANG RD SOUTHWEST AVIATION INDUSTRIAL DEVELOPMENT ZONE SHUANGLIU CHENGDU, SICHUAN 610207 CHINA LED Lighting Modules, Cat. No. BV-ALUMINUM-PIRANHA Series. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited te draw a total wattage of no greater than the secondary current rating of each Class 2 power supply. 4. These products are suitable for use in dry, damp and wet locations without additional enclosures. Operating Voltage Current per Watts per LED quantity Part No.(VDC)module C mA) module (W) Emitting color (pc) BV-Aluminum-Piranha-R 12 40 0.48 Red 14 BV-Aluminum- Piranha-Y 12 30 0.36 Yellow 14 BV-Aluminum- Piranha-A 12 30 0.36 Amber 14 4